summaryrefslogtreecommitdiffstats
path: root/chipset_enable.c
diff options
context:
space:
mode:
Diffstat (limited to 'chipset_enable.c')
-rw-r--r--chipset_enable.c82
1 files changed, 5 insertions, 77 deletions
diff --git a/chipset_enable.c b/chipset_enable.c
index bb18b4d..8d64e0c 100644
--- a/chipset_enable.c
+++ b/chipset_enable.c
@@ -693,10 +693,9 @@ static int enable_flash_amd8111(struct pci_dev *dev, const char *name)
static int enable_flash_sb600(struct pci_dev *dev, const char *name)
{
- uint32_t tmp, prot;
+ uint32_t prot;
uint8_t reg;
- struct pci_dev *smbus_dev;
- int has_spi = 1;
+ int ret;
/* Clear ROM protect 0-3. */
for (reg = 0x50; reg < 0x60; reg += 4) {
@@ -720,80 +719,9 @@ static int enable_flash_sb600(struct pci_dev *dev, const char *name)
(prot & 0xfffffc00) + ((prot & 0x3ff) << 8));
}
- /* Read SPI_BaseAddr */
- tmp = pci_read_long(dev, 0xa0);
- tmp &= 0xffffffe0; /* remove bits 4-0 (reserved) */
- msg_pdbg("SPI base address is at 0x%x\n", tmp);
-
- /* If the BAR has address 0, it is unlikely SPI is used. */
- if (!tmp)
- has_spi = 0;
-
- if (has_spi) {
- /* Physical memory has to be mapped at page (4k) boundaries. */
- sb600_spibar = physmap("SB600 SPI registers", tmp & 0xfffff000,
- 0x1000);
- /* The low bits of the SPI base address are used as offset into
- * the mapped page.
- */
- sb600_spibar += tmp & 0xfff;
-
- tmp = pci_read_long(dev, 0xa0);
- msg_pdbg("AltSpiCSEnable=%i, SpiRomEnable=%i, "
- "AbortEnable=%i\n", tmp & 0x1, (tmp & 0x2) >> 1,
- (tmp & 0x4) >> 2);
- tmp = (pci_read_byte(dev, 0xba) & 0x4) >> 2;
- msg_pdbg("PrefetchEnSPIFromIMC=%i, ", tmp);
-
- tmp = pci_read_byte(dev, 0xbb);
- msg_pdbg("PrefetchEnSPIFromHost=%i, SpiOpEnInLpcMode=%i\n",
- tmp & 0x1, (tmp & 0x20) >> 5);
- tmp = mmio_readl(sb600_spibar);
- msg_pdbg("SpiArbEnable=%i, SpiAccessMacRomEn=%i, "
- "SpiHostAccessRomEn=%i, ArbWaitCount=%i, "
- "SpiBridgeDisable=%i, DropOneClkOnRd=%i\n",
- (tmp >> 19) & 0x1, (tmp >> 22) & 0x1,
- (tmp >> 23) & 0x1, (tmp >> 24) & 0x7,
- (tmp >> 27) & 0x1, (tmp >> 28) & 0x1);
- }
-
- /* Look for the SMBus device. */
- smbus_dev = pci_dev_find(0x1002, 0x4385);
-
- if (has_spi && !smbus_dev) {
- msg_perr("ERROR: SMBus device not found. Not enabling SPI.\n");
- has_spi = 0;
- }
- if (has_spi) {
- /* Note about the bit tests below: If a bit is zero, the GPIO is SPI. */
- /* GPIO11/SPI_DO and GPIO12/SPI_DI status */
- reg = pci_read_byte(smbus_dev, 0xAB);
- reg &= 0xC0;
- msg_pdbg("GPIO11 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_DO");
- msg_pdbg("GPIO12 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_DI");
- if (reg != 0x00)
- has_spi = 0;
- /* GPIO31/SPI_HOLD and GPIO32/SPI_CS status */
- reg = pci_read_byte(smbus_dev, 0x83);
- reg &= 0xC0;
- msg_pdbg("GPIO31 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_HOLD");
- msg_pdbg("GPIO32 used for %s\n", (reg & (1 << 7)) ? "GPIO" : "SPI_CS");
- /* SPI_HOLD is not used on all boards, filter it out. */
- if ((reg & 0x80) != 0x00)
- has_spi = 0;
- /* GPIO47/SPI_CLK status */
- reg = pci_read_byte(smbus_dev, 0xA7);
- reg &= 0x40;
- msg_pdbg("GPIO47 used for %s\n", (reg & (1 << 6)) ? "GPIO" : "SPI_CLK");
- if (reg != 0x00)
- has_spi = 0;
- }
-
buses_supported = CHIP_BUSTYPE_LPC | CHIP_BUSTYPE_FWH;
- if (has_spi) {
- buses_supported |= CHIP_BUSTYPE_SPI;
- spi_controller = SPI_CONTROLLER_SB600;
- }
+
+ ret = sb600_probe_spi(dev);
/* Read ROM strap override register. */
OUTB(0x8f, 0xcd6);
@@ -830,7 +758,7 @@ static int enable_flash_sb600(struct pci_dev *dev, const char *name)
OUTB(0x0e, 0xcd7);
*/
- return 0;
+ return ret;
}
static int enable_flash_nvidia_nforce2(struct pci_dev *dev, const char *name)
OpenPOWER on IntegriCloud