diff options
| -rw-r--r-- | Documentation/serprog-protocol.txt | 7 | ||||
| -rw-r--r-- | serprog.c | 17 | ||||
| -rw-r--r-- | serprog.h | 1 |
3 files changed, 24 insertions, 1 deletions
diff --git a/Documentation/serprog-protocol.txt b/Documentation/serprog-protocol.txt index 821cf28..58f4417 100644 --- a/Documentation/serprog-protocol.txt +++ b/Documentation/serprog-protocol.txt @@ -34,6 +34,7 @@ COMMAND Description Parameters Return Value 0x13 Perform SPI operation 24-bit slen + 24-bit rlen ACK + rlen bytes of data / NAK + slen bytes of data 0x14 Set SPI clock frequency in Hz 32-bit requested frequency ACK + 32-bit set frequency / NAK +0x15 Toggle flash chip pin drivers 8-bit (0 disable, else enable) ACK / NAK 0x?? unimplemented command - invalid. @@ -82,6 +83,12 @@ Additional information of the above commands: lower than the one requested. If there is no lower frequency available the lowest possible should be used. The value chosen is sent back in the reply with an ACK. + 0x15 (S_CMD_S_PIN_STATE): + Sets the state of the pin drivers connected to the flash chip. Disabling them allows other + devices (e.g. a mainboard's chipset) to access the chip. This way the serprog controller can + remain attached to the flash chip even when the board is running. The user is responsible to + NOT connect VCC and other permanently externally driven signals to the programmer as needed. + If the value is 0, then the drivers should be disabled, otherwise they should be enabled. About mandatory commands: The only truly mandatory commands for any device are 0x00, 0x01, 0x02 and 0x10, but one can't really do anything with these commands. @@ -664,6 +664,15 @@ int serprog_init(void) sp_device_opbuf_size); } + if (sp_check_commandavail(S_CMD_S_PIN_STATE)) { + uint8_t en = 1; + if (sp_docommand(S_CMD_S_PIN_STATE, 1, &en, 0, NULL) != 0) { + msg_perr("Error: could not enable output buffers\n"); + return 1; + } else + msg_pdbg(MSGHEADER "Output drivers enabled\n"); + } else + msg_pdbg(MSGHEADER "Warning: Programmer does not support toggling its output drivers\n"); sp_prev_was_write = 0; sp_streamed_transmit_ops = 0; sp_streamed_transmit_bytes = 0; @@ -736,9 +745,15 @@ static void sp_execute_opbuf(void) static int serprog_shutdown(void *data) { - msg_pspew("%s\n", __func__); if ((sp_opbuf_usage) || (sp_max_write_n && sp_write_n_bytes)) sp_execute_opbuf(); + if (sp_check_commandavail(S_CMD_S_PIN_STATE)) { + uint8_t dis = 0; + if (sp_docommand(S_CMD_S_PIN_STATE, 1, &dis, 0, NULL) == 0) + msg_pdbg(MSGHEADER "Output drivers disabled\n"); + else + msg_perr(MSGHEADER "%s: Warning: could not disable output buffers\n", __func__); + } /* FIXME: fix sockets on windows(?), especially closing */ serialport_shutdown(&sp_fd); if (sp_max_write_n) @@ -22,3 +22,4 @@ #define S_CMD_S_BUSTYPE 0x12 /* Set used bustype(s). */ #define S_CMD_O_SPIOP 0x13 /* Perform SPI operation. */ #define S_CMD_S_SPI_FREQ 0x14 /* Set SPI clock frequency */ +#define S_CMD_S_PIN_STATE 0x15 /* Enable/disable output drivers */ |
