summaryrefslogtreecommitdiffstats
path: root/flashrom.8.tmpl
diff options
context:
space:
mode:
authorStefan Tauner <stefan.tauner@alumni.tuwien.ac.at>2016-03-13 15:16:30 +0000
committerStefan Tauner <stefan.tauner@alumni.tuwien.ac.at>2016-03-13 15:16:30 +0000
commit0be072cbe4d05b1e69d1c02291f3a2a544beb2af (patch)
tree3c4270b0bdf66cd15fcc6b2525c0ff9aa4a803ab /flashrom.8.tmpl
parentfc3ecc2a812235fce1a4cdc7dc3338507150e8c7 (diff)
downloadast2050-flashrom-0be072cbe4d05b1e69d1c02291f3a2a544beb2af.zip
ast2050-flashrom-0be072cbe4d05b1e69d1c02291f3a2a544beb2af.tar.gz
Add a bunch of new/tested stuff and various small changes 25
Tested mainboards: OK: - ASRock Fatal1ty 970 Performance and P4i65G Reported by anonymous email message ID: 932677687262b1300eaf14260999d9262c31@guerrillamail.com The latter actually had a tested board enable already. Flash chips: - Eon EN25Q128 to PREW (+PREW) Reported by Adrian Graham - GigaDevice GD25VQ41B to PREW (+PREW) Reported by David Hendricks - Winbond W39V040FB to PREW (+EW) Reported by fjed on IRC Miscellaneous: - Change PCI IDs of "MS-6577 (Xenon)" board enable. The previous IDs contained the on-board display adapter which is disabled when a dedicated graphics card is installed. - Add a note to the README how to overcome the clang warning if only a single programmer is enabled. - Fix some typo and manpage problems found by lintian - r1920 introduced some explicit calls to pkg-config instead of $(PKG_CONFIG). This patch corrects that. - Make MS-7094 (K8T Neo2-F V2.0) board enable less contestable. Previous PCI IDs were board-specific but ot the other of devices that could be disabled by the firmware or that vary among hardware revions. There are no good alternatives available. However, since we always have a DMI decoder available now, we can use non-board-specific devices without taking risks. Thanks to Uwe Hermann for reporting and testing. - Some other small changes to clean up whitespace and fix some warnings from Debian's lintian. Corresponding to flashrom svn r1951. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
Diffstat (limited to 'flashrom.8.tmpl')
-rw-r--r--flashrom.8.tmpl38
1 files changed, 21 insertions, 17 deletions
diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl
index cb77e46..34e1fe7 100644
--- a/flashrom.8.tmpl
+++ b/flashrom.8.tmpl
@@ -1,9 +1,11 @@
.\" Load the www device when using groff; provide a fallback for groff's MTO macro that formats email addresses.
.ie \n[.g] \
. mso www.tmac
-.el \
-. de MTO \\$2 \(la\\$1 \(ra\\$3
+.el \{
+. de MTO
+ \\$2 \(la\\$1 \(ra\\$3 \
. .
+.\}
.\" Create wrappers for .MTO and .URL that print only text on systems w/o groff or if not outputting to a HTML
.\" device. To that end we need to distinguish HTML output on groff from other configurations first.
.nr groffhtml 0
@@ -208,7 +210,7 @@ Please note that MediaWiki output is not compiled in by default.
Specify the programmer device. This is mandatory for all operations
involving any chip access (probe/read/write/...). Currently supported are:
.sp
-.BR "* internal" " (default, for in-system flashing in the mainboard)"
+.BR "* internal" " (for in-system flashing in the mainboard)"
.sp
.BR "* dummy" " (virtual programmer for testing flashrom)"
.sp
@@ -237,16 +239,10 @@ cards)"
.sp
.BR "* it8212" " (for flash ROMs on ITE IT8212F ATA/RAID controller)"
.sp
-.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family \
-based USB SPI programmer), including the DLP Design DLP-USB1232H, \
-FTDI FT2232H Mini-Module, FTDI FT4232H Mini-Module, openbiosprog-spi, Amontec \
-JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster, \
-Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, TIAO/DIYGADGET USB
-Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2.
+.BR "* ft2232_spi" " (for SPI flash ROMs attached to an FT2232/FT4232H/FT232H family based USB SPI programmer).
.sp
.BR "* serprog" " (for flash ROMs attached to a programmer speaking serprog, \
-including Arduino-based devices as well as various programmers by Urja Rannikko, \
-Juhana Helovuo, Stefan Tauner and others)."
+including some Arduino-based devices)."
.sp
.BR "* buspirate_spi" " (for SPI flash ROMs attached to a Bus Pirate)"
.sp
@@ -684,13 +680,18 @@ size (padding to 32 kB is required).
.IP
This is the first programmer module in flashrom that does not provide access to NOR flash chips but EEPROMs
mounted on gigabit Ethernet cards based on Intel's 82580 NIC. Because EEPROMs normally do not announce their
-size nor allow to be identified, the controller relies on correct size values written to predefined addresses
-within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an unprogrammed
-EEPROM/card is detected. Intel specifies following EEPROMs to be compatible: Atmel AT25128, AT25256, Micron (ST)
-M95128, M95256 and OnSemi (Catalyst) CAT25CS128.
+size nor allow themselves to be identified, the controller relies on correct size values written to predefined
+addresses within the chip. Flashrom follows this scheme but assumes the minimum size of 16 kB (128 kb) if an
+unprogrammed EEPROM/card is detected. Intel specifies following EEPROMs to be compatible:
+Atmel AT25128, AT25256, Micron (ST) M95128, M95256 and OnSemi (Catalyst) CAT25CS128.
.SS
.BR "ft2232_spi " programmer
.IP
+This module supports various programmers based on FTDI FT2232/FT4232H/FT232H chips including the DLP Design
+DLP-USB1232H, openbiosprog-spi, Amontec JTAGkey/JTAGkey-tiny/JTAGkey-2, Dangerous Prototypes Bus Blaster,
+Olimex ARM-USB-TINY/-H, Olimex ARM-USB-OCD/-H, OpenMoko Neo1973 Debug board (V2+), TIAO/DIYGADGET USB
+Multi-Protocol Adapter (TUMPA), TUMPA Lite, GOEPEL PicoTAP and Google Servo v1/v2.
+.sp
An optional parameter specifies the controller
type and channel/interface/port it should support. For that you have to use the
.sp
@@ -736,6 +737,9 @@ syntax.
.SS
.BR "serprog " programmer
.IP
+This module supports all programmers speaking the serprog protocol. This includes some Arduino-based devices
+as well as various programmers by Urja Rannikko, Juhana Helovuo, Stefan Tauner, Chi Zhang and many others.
+.sp
A mandatory parameter specifies either a serial device (and baud rate) or an IP/port combination for
communicating with the programmer.
The device/baud combination has to start with
@@ -981,7 +985,7 @@ Please note that the linux_spi driver only works on Linux.
.BR "mstarddc_spi " programmer
.IP
The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging
-informations between a computer and attached displays. Its most common uses are getting display capabilities
+information between a computer and attached displays. Its most common uses are getting display capabilities
through EDID (at I2C address 0x50) and sending commands to the display using the DDC/CI protocol (at address
0x37). On displays driven by MSTAR SoCs, it is also possible to access the SoC firmware flash (connected to
the Soc through another SPI bus) using an In-System Programming (ISP) port, usually at address 0x49.
@@ -1016,7 +1020,7 @@ Example that does not reset the display at the end of the operation:
.sp
.B " flashrom \-p mstarddc_spi:dev=/dev/i2c-1:49,noreset=1
.sp
-Please note that sending the reset command is also inhibited in the event an error occured during the operation.
+Please note that sending the reset command is also inhibited if an error occurred during the operation.
To send the reset command afterwards, you can simply run flashrom once more, in chip probe mode (not specifying
an operation), without the
.B noreset
OpenPOWER on IntegriCloud