1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
|
/*
* All Rights Reserved, Copyright (C) Fujitsu Limited 1995
*
* This software may be used, modified, copied, distributed, and sold, in
* both source and binary form provided that the above copyright, these
* terms and the following disclaimer are retained. The name of the author
* and/or the contributor may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*/
#define FE_MB86960_H_VERSION "mb86960.h ver. 0.8"
/*
* Registers of Fujitsu MB86960A/MB86965A Ethernet controller.
* Written and contributed by M.S. <seki@sysrap.cs.fujitsu.co.jp>
*/
/*
* Notes on register naming:
*
* Fujitsu documents for MB86960A/MB86965A uses no mnemorable names
* for their registers. They defined only three names for 32
* registers and appended numbers to distinguish registers of
* same name. Surprisingly, the numbers represent I/O address
* offsets of the registers from the base addresses, and their
* names correspond to the "bank" the registers are allocated.
* All this means that, for example, to say "read DLCR8" has no more
* than to say "read a register at offset 8 on bank DLCR."
*
* The following definitions may look silly, but that's what Fujitsu
* did, and it is necessary to know these names to read Fujitsu
* documents..
*/
/* Data Link Control Registrs, on invaliant port addresses. */
#define FE_DLCR0 0
#define FE_DLCR1 1
#define FE_DLCR2 2
#define FE_DLCR3 3
#define FE_DLCR4 4
#define FE_DLCR5 5
#define FE_DLCR6 6
#define FE_DLCR7 7
/* More DLCRs, on register bank #0. */
#define FE_DLCR8 8
#define FE_DLCR9 9
#define FE_DLCR10 10
#define FE_DLCR11 11
#define FE_DLCR12 12
#define FE_DLCR13 13
#define FE_DLCR14 14
#define FE_DLCR15 15
/* Malticast Address Registers. On register bank #1. */
#define FE_MAR8 8
#define FE_MAR9 9
#define FE_MAR10 10
#define FE_MAR11 11
#define FE_MAR12 12
#define FE_MAR13 13
#define FE_MAR14 14
#define FE_MAR15 15
/* Buffer Memory Port Registers. On register back #2. */
#define FE_BMPR8 8
#define FE_BMPR9 9
#define FE_BMPR10 10
#define FE_BMPR11 11
#define FE_BMPR12 12
#define FE_BMPR13 13
#define FE_BMPR14 14
#define FE_BMPR15 15
/* More BMPRs, only on MB86965A, accessible only when JLI mode. */
#define FE_BMPR16 16
#define FE_BMPR17 17
#define FE_BMPR18 18
#define FE_BMPR19 19
/*
* Definitions of registers.
* I don't have Fujitsu documents of MB86960A/MB86965A, so I don't
* know the official names for each flags and fields. The following
* names are assigned by me (the author of this file,) since I cannot
* mnemorize hexadecimal constants for all of these functions.
* Comments? FIXME.
*/
/* DLCR0 -- transmitter status */
#define FE_D0_BUSERR 0x01 /* Bus write error */
#define FE_D0_COLL16 0x02 /* Collision limit (16) encountered */
#define FE_D0_COLLID 0x04 /* Collision on last transmission */
#define FE_D0_JABBER 0x08 /* Jabber */
#define FE_D0_CRLOST 0x10 /* Carrier lost on last transmission */
#define FE_D0_PKTRCD 0x20 /* No corrision on last transmission */
#define FE_D0_NETBSY 0x40 /* Network Busy (Carrier Detected) */
#define FE_D0_TXDONE 0x80 /* Transmission complete */
/* DLCR1 -- receiver status */
#define FE_D1_OVRFLO 0x01 /* Receiver buffer overflow */
#define FE_D1_CRCERR 0x02 /* CRC error on last packet */
#define FE_D1_ALGERR 0x04 /* Alignment error on last packet */
#define FE_D1_SRTPKT 0x08 /* Short (RUNT) packet is received */
#define FE_D1_RMTRST 0x10 /* Remote reset packet (type = 0x0900) */
#define FE_D1_DMAEOP 0x20 /* Host asserted End of DMA OPeration */
#define FE_D1_BUSERR 0x40 /* Bus read error */
#define FE_D1_PKTRDY 0x80 /* Packet(s) ready on receive buffer */
/* DLCR2 -- transmitter interrupt control; same layout as DLCR0 */
#define FE_D2_BUSERR FE_D0_BUSERR
#define FE_D2_COLL16 FE_D0_COLL16
#define FE_D2_COLLID FE_D0_COLLID
#define FE_D2_JABBER FE_D0_JABBER
#define FE_D2_TXDONE FE_D0_TXDONE
#define FE_D2_RESERVED 0x70
/* DLCR3 -- receiver interrupt control; same layout as DLCR1 */
#define FE_D3_OVRFLO FE_D1_OVRFLO
#define FE_D3_CRCERR FE_D1_CRCERR
#define FE_D3_ALGERR FE_D1_ALGERR
#define FE_D3_SRTPKT FE_D1_SRTPKT
#define FE_D3_RMTRST FE_D1_RMTRST
#define FE_D3_DMAEOP FE_D1_DMAEOP
#define FE_D3_BUSERR FE_D1_BUSERR
#define FE_D3_PKTRDY FE_D1_PKTRDY
/* DLCR4 -- transmitter operation mode */
#define FE_D4_DSC 0x01 /* Disable carrier sense on trans. */
#define FE_D4_LBC 0x02 /* Loop back test control */
#define FE_D4_CNTRL 0x04 /* - ??? */
#define FE_D4_TEST1 0x08 /* Test output #1 */
#define FE_D4_COL 0xF0 /* Collision counter */
#define FE_D4_LBC_ENABLE 0x00 /* Perform loop back test */
#define FE_D4_LBC_DISABLE 0x02 /* Normal operation */
#define FE_D4_COL_SHIFT 4
/* DLCR5 -- receiver operation mode */
#define FE_D5_AFM0 0x01 /* Receive packets for other stations */
#define FE_D5_AFM1 0x02 /* Receive packets for this station */
#define FE_D5_RMTRST 0x04 /* Enable remote reset operation */
#define FE_D5_SRTPKT 0x08 /* Accept short (RUNT) packets */
#define FE_D5_SRTADR 0x10 /* Short (16 bits?) MAC address */
#define FE_D5_BADPKT 0x20 /* Accept packets with error */
#define FE_D5_BUFEMP 0x40 /* Receive buffer is empty */
#define FE_D5_TEST2 0x80 /* Test output #2 */
/* DLCR6 -- hardware configuration #0 */
#define FE_D6_BUFSIZ 0x03 /* Size of NIC buffer SRAM */
#define FE_D6_TXBSIZ 0x0C /* Size (and config)of trans. buffer */
#define FE_D6_BBW 0x10 /* Buffer SRAM bus width */
#define FE_D6_SBW 0x20 /* System bus width */
#define FE_D6_SRAM 0x40 /* Buffer SRAM access time */
#define FE_D6_DLC 0x80 /* Disable DLC (recever/transmitter) */
#define FE_D6_BUFSIZ_8KB 0x00 /* The board has 8KB SRAM */
#define FE_D6_BUFSIZ_16KB 0x01 /* The board has 16KB SRAM */
#define FE_D6_BUFSIZ_32KB 0x02 /* The board has 32KB SRAM */
#define FE_D6_BUFSIZ_64KB 0x03 /* The board has 64KB SRAM */
#define FE_D6_TXBSIZ_1x2KB 0x00 /* Single 2KB buffer for trans. */
#define FE_D6_TXBSIZ_2x2KB 0x04 /* Double 2KB buffers */
#define FE_D6_TXBSIZ_2x4KB 0x08 /* Double 4KB buffers */
#define FE_D6_TXBSIZ_2x8KB 0x0C /* Double 8KB buffers */
#define FE_D6_BBW_WORD 0x00 /* SRAM has 16 bit data line */
#define FE_D6_BBW_BYTE 0x10 /* SRAM has 8 bit data line */
#define FE_D6_SBW_WORD 0x00 /* Access with 16 bit (AT) bus */
#define FE_D6_SBW_BYTE 0x20 /* Access with 8 bit (XT) bus */
#define FE_D6_SRAM_150ns 0x00 /* The board has slow SRAM */
#define FE_D6_SRAM_100ns 0x40 /* The board has fast SRAM */
#define FE_D6_DLC_ENABLE 0x00 /* Normal operation */
#define FE_D6_DLC_DISABLE 0x80 /* Stop sending/receiving */
/* DLC7 -- hardware configuration #1 */
#define FE_D7_BYTSWP 0x01 /* Host byte order control */
#define FE_D7_EOPPOL 0x02 /* Polarity of DMA EOP signal */
#define FE_D7_RBS 0x0C /* Register bank select */
#define FE_D7_RDYPNS 0x10 /* Senses RDYPNSEL input signal */
#define FE_D7_POWER 0x20 /* Stand-by (power down) mode control */
#define FE_D7_IDENT 0xC0 /* Chip identification */
#define FE_D7_BYTSWP_LH 0x00 /* DEC/Intel byte order */
#define FE_D7_BYTSWP_HL 0x01 /* IBM/Motorolla byte order */
#define FE_D7_RBS_DLCR 0x00 /* Select DLCR8-15 */
#define FE_D7_RBS_MAR 0x04 /* Select MAR8-15 */
#define FE_D7_RBS_BMPR 0x08 /* Select BMPR8-15 */
#define FE_D7_POWER_DOWN 0x00 /* Power down (stand-by) mode */
#define FE_D7_POWER_UP 0x20 /* Normal operation */
#define FE_D7_IDENT_NICE 0x80
#define FE_D7_IDENT_EC 0xC0
/* DLCR8 thru DLCR13 are for Ethernet station address. */
/* DLCR14 and DLCR15 are for TDR. (BTW, what is TDR? FIXME.) */
/* MAR8 thru MAR15 are for Multicast address filter. */
/* BMPR8 and BMPR9 are for packet data. */
/* BMPR10 -- transmitter start trigger */
#define FE_B10_START 0x80 /* Start transmitter */
#define FE_B10_COUNT 0x7F /* Packet count */
/* BMPR11 -- 16 collisions control */
#define FE_B11_CTRL 0x01 /* Skip or resend errored packets */
#define FE_B11_MODE1 0x02 /* Restart transmitter after COLL16 */
#define FE_B11_MODE2 0x04 /* Automatic restart enable */
#define FE_B11_CTRL_RESEND 0x00 /* Re-send the collided packet */
#define FE_B11_CTRL_SKIP 0x01 /* Skip the collided packet */
/* BMPR12 -- DMA enable */
#define FE_B12_TXDMA 0x01 /* Enable transmitter DMA */
#define FE_B12_RXDMA 0x02 /* Enable receiver DMA */
/* BMPR13 -- DMA control */
#define FE_B13_BSTCTL 0x03 /* DMA burst mode control */
#define FE_B13_TPTYPE 0x04 /* Twisted pair cable impedance */
#define FE_B13_PORT 0x18 /* Port (TP/AUI) selection */
#define FE_B13_LNKTST 0x20 /* Link test enable */
#define FE_B13_SQTHLD 0x40 /* Lower squelch threshold */
#define FE_B13_IOUNLK 0x80 /* Change I/O base address */
#define FE_B13_BSTCTL_1 0x00
#define FE_B13_BSTCTL_4 0x01
#define FE_B13_BSTCTL_8 0x02
#define FE_B13_BSTCLT_12 0x03
#define FE_B13_TPTYPE_UTP 0x00 /* Unshielded (standard) cable */
#define FE_B13_TPTYPE_STP 0x04 /* Shielded (IBM) cable */
#define FE_B13_PORT_AUTO 0x00 /* Auto detected */
#define FE_B13_PORT_TP 0x08 /* Force TP */
#define FE_B13_PORT_AUI 0x18 /* Force AUI */
/* BMPR14 -- More receiver control and more transmission interrupts */
#define FE_B14_FILTER 0x01 /* Filter out self-originated packets */
#define FE_B14_SQE 0x02 /* SQE interrupt enable */
#define FE_B14_SKIP 0x04 /* Skip a received packet */
#define FE_B14_RJAB 0x20 /* RJAB interrupt enable */
#define FE_B14_LLD 0x40 /* Local-link-down interrupt enable */
#define FE_B14_RLD 0x80 /* Remote-link-down interrupt enable */
/* BMPR15 -- More transmitter status; basically same layout as BMPR14 */
#define FE_B15_SQE FE_B14_SQE
#define FE_B15_RCVPOL 0x08 /* Reversed receive line polarity */
#define FE_B15_RMTPRT 0x10 /* ??? */
#define FE_B15_RAJB FE_B14_RJAB
#define FE_B15_LLD FE_B14_LLD
#define FE_B15_RLD FE_B14_RLD
/* BMPR16 -- EEPROM control */
#define FE_B16_DOUT 0x04 /* EEPROM Data in (CPU to EEPROM) */
#define FE_B16_SELECT 0x20 /* EEPROM chip select */
#define FE_B16_CLOCK 0x40 /* EEPROM shift clock */
#define FE_B16_DIN 0x80 /* EEPROM data out (EEPROM to CPU) */
/* BMPR17 -- EEPROM data */
#define FE_B17_DATA 0x80 /* EEPROM data bit */
/* BMPR18 ??? */
/* BMPR19 -- ISA interface configuration */
#define FE_B19_IRQ 0xC0
#define FE_B19_IRQ_SHIFT 6
#define FE_B19_ROM 0x38
#define FE_B19_ROM_SHIFT 3
#define FE_B19_ADDR 0x07
#define FE_B19_ADDR_SHIFT 0
/*
* EEPROM specification (of JLI mode).
*/
/* Number of bytes in an EEPROM accessible through 86965. */
#define FE_EEPROM_SIZE 32
/* Offset for JLI config; automatically copied into BMPR19 at startup. */
#define FE_EEPROM_CONF 0
/*
* Some 86960 specific constants.
*/
/* Length (in bytes) of a Multicast Address Filter. */
#define FE_FILTER_LEN 8
/* How many packets we can put in the transmission buffer on NIC memory. */
#define FE_QUEUEING_MAX 127
/* Length (in bytes) of a "packet length" word in transmission buffer. */
#define FE_DATA_LEN_LEN 2
/* Special Multicast Address Filter value. */
#define FE_FILTER_NOTHING { 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00 }
#define FE_FILTER_ALL { 0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF,0xFF }
|
