1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
|
/*
* All Rights Reserved, Copyright (C) Fujitsu Limited 1995
*
* This software may be used, modified, copied, distributed, and sold, in
* both source and binary form provided that the above copyright, these
* terms and the following disclaimer are retained. The name of the author
* and/or the contributor may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND THE CONTRIBUTOR ``AS IS'' AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
* ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR THE CONTRIBUTOR BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION.
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
#include "opt_fe.h"
#include "opt_inet.h"
#include "opt_ipx.h"
#include <sys/param.h>
#include <sys/kernel.h>
#include <sys/socket.h>
#include <sys/systm.h>
#include <sys/module.h>
#include <sys/bus.h>
#include <machine/bus.h>
#include <machine/resource.h>
#include <net/ethernet.h>
#include <net/if.h>
#include <net/if_mib.h>
#include <net/if_media.h>
#include <netinet/in.h>
#include <netinet/if_ether.h>
#include <i386/isa/ic/mb86960.h>
#include <dev/fe/if_fereg.h>
#include <dev/fe/if_fevar.h>
#include <dev/pccard/pccardvar.h>
#include <pccard/cardinfo.h>
/*
* PC-Card (PCMCIA) specific code.
*/
static int fe_pccard_probe(device_t);
static int fe_pccard_attach(device_t);
static int fe_pccard_detach(device_t);
static device_method_t fe_pccard_methods[] = {
/* Device interface */
DEVMETHOD(device_probe, fe_pccard_probe),
DEVMETHOD(device_attach, fe_pccard_attach),
DEVMETHOD(device_detach, fe_pccard_detach),
{ 0, 0 }
};
static driver_t fe_pccard_driver = {
"fe",
fe_pccard_methods,
sizeof (struct fe_softc)
};
DRIVER_MODULE(fe, pccard, fe_pccard_driver, fe_devclass, 0, 0);
static int fe_probe_mbh(device_t);
static int fe_probe_tdk(device_t);
/*
* Initialize the device - called from Slot manager.
*/
static int
fe_pccard_probe(device_t dev)
{
struct fe_softc *sc;
int error;
/* Prepare for the device probe process. */
sc = device_get_softc(dev);
sc->sc_unit = device_get_unit(dev);
pccard_get_ether(dev, sc->sc_enaddr);
/* Probe for supported cards. */
if ((error = fe_probe_mbh(dev)) == 0)
goto end;
fe_release_resource(dev);
if ((error = fe_probe_tdk(dev)) == 0)
goto end;
fe_release_resource(dev);
end:
if (error == 0)
error = fe_alloc_irq(dev, 0);
fe_release_resource(dev);
return (error);
}
static int
fe_pccard_attach(device_t dev)
{
struct fe_softc *sc = device_get_softc(dev);
if (sc->port_used)
fe_alloc_port(dev, sc->port_used);
fe_alloc_irq(dev, 0);
return fe_attach(dev);
}
/*
* feunload - unload the driver and clear the table.
* XXX TODO:
* This is usually called when the card is ejected, but
* can be caused by a modunload of a controller driver.
* The idea is to reset the driver's view of the device
* and ensure that any driver entry points such as
* read and write do not hang.
*/
static int
fe_pccard_detach(device_t dev)
{
struct fe_softc *sc = device_get_softc(dev);
struct ifnet *ifp = &sc->arpcom.ac_if;
fe_stop(sc);
ether_ifdetach(ifp, ETHER_BPF_SUPPORTED);
bus_teardown_intr(dev, sc->irq_res, sc->irq_handle);
fe_release_resource(dev);
return 0;
}
/*
* Probe and initialization for Fujitsu MBH10302 PCMCIA Ethernet interface.
* Note that this is for 10302 only; MBH10304 is handled by fe_probe_tdk().
*/
static void
fe_init_mbh(struct fe_softc *sc)
{
/* Minimal initialization of 86960. */
DELAY(200);
fe_outb(sc, FE_DLCR6, sc->proto_dlcr6 | FE_D6_DLC_DISABLE);
DELAY(200);
/* Disable all interrupts. */
fe_outb(sc, FE_DLCR2, 0);
fe_outb(sc, FE_DLCR3, 0);
/* Enable master interrupt flag. */
fe_outb(sc, FE_MBH0, FE_MBH0_MAGIC | FE_MBH0_INTR_ENABLE);
}
static int
fe_probe_mbh(device_t dev)
{
struct fe_softc *sc = device_get_softc(dev);
static struct fe_simple_probe_struct probe_table [] = {
{ FE_DLCR2, 0x58, 0x00 },
{ FE_DLCR4, 0x08, 0x00 },
{ FE_DLCR6, 0xFF, 0xB6 },
{ 0 }
};
/* MBH10302 occupies 32 I/O addresses. */
if (fe_alloc_port(dev, 32))
return ENXIO;
/* Ethernet MAC address should *NOT* have been given by pccardd,
if this is a true MBH10302; i.e., Ethernet address must be
"all-zero" upon entry. */
if (sc->sc_enaddr[0] || sc->sc_enaddr[1] || sc->sc_enaddr[2] ||
sc->sc_enaddr[3] || sc->sc_enaddr[4] || sc->sc_enaddr[5])
return ENXIO;
/* Fill the softc struct with default values. */
fe_softc_defaults(sc);
/*
* See if MBH10302 is on its address.
* I'm not sure the following probe code works. FIXME.
*/
if (!fe_simple_probe(sc, probe_table))
return ENXIO;
/* Get our station address from EEPROM. */
fe_inblk(sc, FE_MBH10, sc->sc_enaddr, ETHER_ADDR_LEN);
/* Make sure we got a valid station address. */
if (!valid_Ether_p(sc->sc_enaddr, 0))
return ENXIO;
/* Determine the card type. */
sc->type = FE_TYPE_MBH;
sc->typestr = "MBH10302 (PCMCIA)";
/* We seems to need our own IDENT bits... FIXME. */
sc->proto_dlcr7 = FE_D7_BYTSWP_LH | FE_D7_IDENT_NICE;
/* Setup hooks. We need a special initialization procedure. */
sc->init = fe_init_mbh;
return 0;
}
/*
* Probe and initialization for TDK/CONTEC PCMCIA Ethernet interface.
* by MASUI Kenji <masui@cs.titech.ac.jp>
*
* (Contec uses TDK Ethenet chip -- hosokawa)
*
* This version of fe_probe_tdk has been rewrote to handle
* *generic* PC card implementation of Fujitsu MB8696x family. The
* name _tdk is just for a historical reason. :-)
*/
static int
fe_probe_tdk (device_t dev)
{
struct fe_softc *sc = device_get_softc(dev);
static struct fe_simple_probe_struct probe_table [] = {
{ FE_DLCR2, 0x50, 0x00 },
{ FE_DLCR4, 0x08, 0x00 },
/* { FE_DLCR5, 0x80, 0x00 }, Does not work well. */
{ 0 }
};
/* C-NET(PC)C occupies 16 I/O addresses. */
if (fe_alloc_port(dev, 16))
return ENXIO;
/* Fill the softc struct with default values. */
fe_softc_defaults(sc);
/*
* See if C-NET(PC)C is on its address.
*/
if (!fe_simple_probe(sc, probe_table))
return ENXIO;
/* Determine the card type. */
sc->type = FE_TYPE_TDK;
sc->typestr = "Generic MB8696x/78Q837x Ethernet (PCMCIA)";
/* Make sure we got a valid station address. */
if (!valid_Ether_p(sc->sc_enaddr, 0))
return ENXIO;
return 0;
}
|