1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
|
/* $NetBSD: s3c2xx0reg.h,v 1.4 2004/02/12 03:47:29 bsh Exp $ */
/*-
* Copyright (c) 2002, 2003 Fujitsu Component Limited
* Copyright (c) 2002, 2003 Genetec Corporation
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright
* notice, this list of conditions and the following disclaimer in the
* documentation and/or other materials provided with the distribution.
* 3. Neither the name of The Fujitsu Component Limited nor the name of
* Genetec corporation may not be used to endorse or promote products
* derived from this software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY FUJITSU COMPONENT LIMITED AND GENETEC
* CORPORATION ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES,
* INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
* MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL FUJITSU COMPONENT LIMITED OR GENETEC
* CORPORATION BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
* SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
* LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
* USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT
* OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
* SUCH DAMAGE.
*
* $FreeBSD$
*/
/*
* Register definitions common to S3C2800 and S3C24[01]0
*/
#ifndef _ARM_S3C2XX0_S3C2XX0REG_H_
#define _ARM_S3C2XX0_S3C2XX0REG_H_
/* UART */
/*
* S3C2800, 2410 and 2400 have a common built-in UART block. However,
* there are small diffs in bit position of some registers.
* Following definitions can be foune in s3c{2800,24x0}reg.h for
* that reason.
*
* ULCON_IR (Infra-red mode)
* ULCON_PARITY_SHIFT (Parity mode bit position)
* UMCON_AFC (Auto flow control)
* UMSTAT_DCTS (CTS change)
*/
#define SSCOM_ULCON 0x00 /* UART line control */
/* ULCON_PARITY_SHIFT and ULCON_IR is defined in s3c{2800,24x0}reg.h */
#define ULCON_PARITY_NONE (0<<ULCON_PARITY_SHIFT)
#define ULCON_PARITY_ODD (4<<ULCON_PARITY_SHIFT)
#define ULCON_PARITY_EVEN (5<<ULCON_PARITY_SHIFT)
#define ULCON_PARITY_ONE (6<<ULCON_PARITY_SHIFT)
#define ULCON_PARITY_ZERO (7<<ULCON_PARITY_SHIFT)
#define ULCON_STOP (1<<2)
#define ULCON_LENGTH_5 0
#define ULCON_LENGTH_6 1
#define ULCON_LENGTH_7 2
#define ULCON_LENGTH_8 3
#define SSCOM_UCON 0x04 /* UART control */
#define UCON_TXINT_TYPE (1<<9) /* Tx interrupt. 0=pulse,1=level */
#define UCON_TXINT_TYPE_LEVEL UCON_TXINT_TYPE
#define UCON_TXINT_TYPE_PULSE 0
#define UCON_RXINT_TYPE (1<<8) /* Rx interrupt */
#define UCON_RXINT_TYPE_LEVEL UCON_RXINT_TYPE
#define UCON_RXINT_TYPE_PULSE 0
#define UCON_TOINT (1<<7) /* Rx timeout interrupt */
#define UCON_ERRINT (1<<6) /* receive error interrupt */
#define UCON_LOOP (1<<5) /* loopback */
#define UCON_SBREAK (1<<4) /* send break */
#define UCON_TXMODE_DISABLE (0<<2)
#define UCON_TXMODE_INT (1<<2)
#define UCON_TXMODE_DMA (2<<2)
#define UCON_TXMODE_MASK (3<<2)
#define UCON_RXMODE_DISABLE (0<<0)
#define UCON_RXMODE_INT (1<<0)
#define UCON_RXMODE_DMA (2<<0)
#define UCON_RXMODE_MASK (3<<0)
#define SSCOM_UFCON 0x08 /* FIFO control */
#define UFCON_TXTRIGGER_0 (0<<6)
#define UFCON_TXTRIGGER_4 (1<<6)
#define UFCON_TXTRIGGER_8 (2<<6)
#define UFCON_TXTRIGGER_16 (3<<6)
#define UFCON_RXTRIGGER_4 (0<<4)
#define UFCON_RXTRIGGER_8 (1<<4)
#define UFCON_RXTRIGGER_12 (2<<4)
#define UFCON_RXTRIGGER_16 (3<<4)
#define UFCON_TXFIFO_RESET (1<<2)
#define UFCON_RXFIFO_RESET (1<<1)
#define UFCON_FIFO_ENABLE (1<<0)
#define SSCOM_UMCON 0x0c /* MODEM control */
/* UMCON_AFC is defined in s3c{2800,24x0}reg.h */
#define UMCON_RTS (1<<0) /* Request to send */
#define SSCOM_UTRSTAT 0x10 /* Status register */
#define UTRSTAT_TXSHIFTER_EMPTY (1<<2)
#define UTRSTAT_TXEMPTY (1<<1) /* TX fifo or buffer empty */
#define UTRSTAT_RXREADY (1<<0) /* RX fifo or buffer is not empty */
#define SSCOM_UERSTAT 0x14 /* Error status register */
#define UERSTAT_BREAK (1<<3) /* Break signal, not 2410 */
#define UERSTAT_FRAME (1<<2) /* Frame error */
#define UERSTAT_PARITY (1<<1) /* Parity error, not 2410 */
#define UERSTAT_OVERRUN (1<<0) /* Overrun */
#define UERSTAT_ALL_ERRORS \
(UERSTAT_OVERRUN|UERSTAT_BREAK|UERSTAT_FRAME|UERSTAT_PARITY)
#define SSCOM_UFSTAT 0x18 /* Fifo status register */
#define UFSTAT_TXFULL (1<<9) /* Tx fifo full */
#define UFSTAT_RXFULL (1<<8) /* Rx fifo full */
#define UFSTAT_TXCOUNT_SHIFT 4 /* TX FIFO count */
#define UFSTAT_TXCOUNT (0x0f<<UFSTAT_TXCOUNT_SHIFT)
#define UFSTAT_RXCOUNT_SHIFT 0 /* RX FIFO count */
#define UFSTAT_RXCOUNT (0x0f<<UFSTAT_RXCOUNT_SHIFT)
#define SSCOM_UMSTAT 0x1c /* Modem status register */
/* UMSTAT_DCTS is defined in s3c{2800,24x0}reg.h */
#define UMSTAT_CTS (1<<0) /* Clear to send */
#if _BYTE_ORDER == _LITTLE_ENDIAN
#define SSCOM_UTXH 0x20 /* Transmit data register */
#define SSCOM_URXH 0x24 /* Receive data register */
#else
#define SSCOM_UTXH 0x23 /* Transmit data register */
#define SSCOM_URXH 0x27 /* Receive data register */
#endif
#define SSCOM_UBRDIV 0x28 /* baud-reate divisor */
#define SSCOM_SIZE 0x2c
/* Interrupt controller (Common to S3c2800/2400X/2410X) */
#define INTCTL_SRCPND 0x00 /* Interrupt request status */
#define INTCTL_INTMOD 0x04 /* Interrupt mode (FIQ/IRQ) */
#define INTCTL_INTMSK 0x08 /* Interrupt mask */
#endif /* _ARM_S3C2XX0_S3C2XX0REG_H_ */
|
