1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
|
.\" $NetBSD: bridge.4,v 1.5 2004/01/31 20:14:11 jdc Exp $
.\"
.\" Copyright 2001 Wasabi Systems, Inc.
.\" All rights reserved.
.\"
.\" Written by Jason R. Thorpe for Wasabi Systems, Inc.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\" notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\" notice, this list of conditions and the following disclaimer in the
.\" documentation and/or other materials provided with the distribution.
.\" 3. All advertising materials mentioning features or use of this software
.\" must display the following acknowledgement:
.\" This product includes software developed for the NetBSD Project by
.\" Wasabi Systems, Inc.
.\" 4. The name of Wasabi Systems, Inc. may not be used to endorse
.\" or promote products derived from this software without specific prior
.\" written permission.
.\"
.\" THIS SOFTWARE IS PROVIDED BY WASABI SYSTEMS, INC. ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED
.\" TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
.\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL WASABI SYSTEMS, INC
.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
.\" POSSIBILITY OF SUCH DAMAGE.
.\"
.\" $FreeBSD$
.\"
.Dd June 10, 2005
.Dt IF_BRIDGE 4
.Os
.Sh NAME
.Nm if_bridge
.Nd network bridge device
.Sh SYNOPSIS
.Cd "device if_bridge"
.Sh DESCRIPTION
The
.Nm
driver creates a logical link between two or more IEEE 802 networks
that use the same (or
.Dq "similar enough" )
framing format.
For example, it is possible to bridge Ethernet and 802.11 networks together,
but it is not possible to bridge Ethernet and Token Ring together.
.Pp
Each
.Nm
interface is created at runtime using interface cloning.
This is
most easily done with the
.Xr ifconfig 8
.Cm create
command or using the
.Va cloned_interfaces
variable in
.Xr rc.conf 5 .
.Pp
A bridge can be used to provide several services, such as a simple
802.11-to-Ethernet bridge for wireless hosts, and traffic isolation.
.Pp
A bridge works like a hub, forwarding traffic from one interface
to another.
Multicast and broadcast packets are always forwarded to all
interfaces that are part of the bridge.
For unicast traffic, the bridge learns which MAC addresses are associated
with which interfaces and will forward the traffic selectively.
.Pp
The
.Nm
driver implements the IEEE 802.1D Spanning Tree protocol (STP).
Spanning Tree is used to detect and remove loops in a network topology.
.Pp
When filtering is enabled, bridged packets will pass through the filter
inbound on the originating interface, on the bridge interface and outbound on
the appropriate interfaces.
Either stage can be disabled, this behaviour can be controlled using
.Xr sysctl 8 :
.Bl -tag -width ".Va net.link.bridge.pfil_member"
.It Va net.link.bridge.pfil_member
Set to
.Li 1
to enable filtering on the incoming and outgoing member interfaces, set
to
.Li 0
to disable it.
.It Va net.link.bridge.pfil_bridge
Set to
.Li 1
to enable filtering on the bridge interface, set
to
.Li 0
to disable it.
.It Va net.link.bridge.ipfw
Set to
.Li 1
to enable layer2 filtering with
.Xr ipfirewall 4 ,
set to
.Li 0
to disable it.
This needs to be enabled for
.Xr dummynet 4
support.
When
.Va ipfw
is enabled,
.Va pfil_bridge
and
.Va pfil_member
will be disabled so that IPFW
is not run twice; these can be re-enabled if desired.
.El
.Pp
ARP and REVARP packets are forwarded without being filtered and others
that are not IP nor IPv6 packets are not forwarded when
.Xr pfil 9
filtering is enabled.
IPFW can filter Ethernet types using
.Cm mac-type
so all packets are passed to
the filter for processing.
.Pp
Note that packets to and from the bridging host will be seen by the
filter on the interface with the appropriate address configured as well
as on the interface on which the packet arrives or departs.
.Pp
The MTU of the first member interface to be added is used as the bridge MTU,
all additional members are required to have exactly the same value.
.Sh EXAMPLES
The following when placed in the file
.Pa /etc/rc.conf
will cause a bridge called
.Dq Li bridge0
to be created, and will add the interfaces
.Dq Li wi0
and
.Dq Li fxp0
to the bridge, and then enable packet forwarding.
Such a configuration could be used to implement a simple
802.11-to-Ethernet bridge (assuming the 802.11 interface is
in ad-hoc mode).
.Bd -literal -offset indent
cloned_interfaces="bridge0"
ifconfig_bridge0="addm wi0 addm fxp0 up"
.Ed
.Pp
Consider a system with two 4-port Ethernet boards.
The following will cause a bridge consisting of all 8 ports with Spanning Tree
enabled to be created:
.Bd -literal -offset indent
ifconfig bridge0 create
ifconfig bridge0 \e
addm fxp0 stp fxp0 \e
addm fxp1 stp fxp1 \e
addm fxp2 stp fxp2 \e
addm fxp3 stp fxp3 \e
addm fxp4 stp fxp4 \e
addm fxp5 stp fxp5 \e
addm fxp6 stp fxp6 \e
addm fxp7 stp fxp7 \e
up
.Ed
.Sh SEE ALSO
.Xr ifconfig 8
.Sh HISTORY
The
.Nm
driver first appeared in
.Fx 6.0 .
.Sh AUTHORS
The
.Nm bridge
driver was originally written by
.An Jason L. Wright
.Aq jason@thought.net
as part of an undergraduate independent study at the University of
North Carolina at Greensboro.
.Pp
This version of the
.Nm
driver has been heavily modified from the original version by
.An Jason R. Thorpe
.Aq thorpej@wasabisystems.com .
.Sh BUGS
The
.Nm
driver currently supports only Ethernet and Ethernet-like (e.g., 802.11)
network devices, with exactly the same interface MTU size as the bridge device.
|