1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
|
.\" Copyright (c) 2013, Sean Bruno <sbruno@freebsd.org>
.\" All rights reserved.
.\"
.\" Redistribution and use in source and binary forms, with or without
.\" modification, are permitted provided that the following conditions
.\" are met:
.\" 1. Redistributions of source code must retain the above copyright
.\" notice, this list of conditions and the following disclaimer.
.\" 2. Redistributions in binary form must reproduce the above copyright
.\" notice, this list of conditions and the following disclaimer in the
.\" documentation and/or other materials provided with the distribution.
.\"
.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
.\" ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
.\" SUCH DAMAGE.
.\"
.\" $FreeBSD$
.\"
.Dd September 13, 2013
.Dt GPIO 4
.Os
.Sh NAME
.Nm gpiobus
.Nd GPIO bus system
.Sh SYNOPSIS
To compile these devices into your kernel and use the device hints, place the
following lines in your kernel configuration file:
.Bd -ragged -offset indent
.Cd "device gpiobus"
.Cd "device gpioiic"
.Cd "device gpio"
.Cd "device gpioc"
.Cd "device gpioled"
.Ed
.Pp
Additional device entries for the
.Li ARM
architecure include:
.Bd -ragged -offset indent
.Cd "device a10_gpio"
.Cd "device bcm_gpio"
.Cd "device imx51_gpio"
.Cd "device lpcgpio"
.Cd "device mv_gpio"
.Cd "device ti_gpio"
.Cd "device gpio_avila"
.Cd "device gpio_cambria"
.Cd "device zy7_gpio"
.Cd "device pxagpio"
.Ed
.Pp
Additional device entries for the
.Li MIPS
architecure include:
.Bd -ragged -offset indent
.Cd "device ar71xxx_gpio"
.Cd "device octeon_gpio"
.Cd "device rt305_gpio"
.Ed
.Pp
Additional device entries for the
.Li POWERPC
architecure include:
.Bd -ragged -offset indent
.Cd "device wiigpio"
.Cd "device macgpio"
.Ed
.Sh DESCRIPTION
The
.Em gpiobus
system provides a simple interface to the bit banging style GPIO bus
found on embedded architectures.
.Pp
The acronym
.Li GPIO
means
.Dq General-Purpose Input/Output.
.Pp
The BUS physically consists of multiple pins that can be configured
for input/output, IRQ delivery, SDA/SCL
.Em iicbus
use, etc.
On most embedded architechtures (mips/arm), discovery of the bus and
configuration of the pins is done via
.Xr device.hints 5
in the platform's kernel
.Xr config 5
file.
.Pp
Assignment of
.Xr gpioiic 4
bus variables is done via:
.Bl -tag -width ".Va hint.gpioiic.%d.atXXX"
.It Va hint.gpioiic.%d.at
Normally just gpiobus0.
.It Va hint.gpioiic.%d.pins
This is a bitmask of the pins on the gpio board that are to be used for
SCLOCK and SDATA from the IIC bus.
To configure pin 0 and 7, use the bitmask of
10000001 and convert it to a hexadecimal value of 0x0081.
Should only ever have two bits set in mask.
.It Va hint.gpioiic.%d.scl
Indicates which bit in the
.Va hint.gpioiic.%d.pins
should be used as the SCLOCK
source.
.It Va hint.gpioiic.%d.sda
Indicates which bit in the
.Va hint.gpioiic.%d.pins
should be used as the SDATA
source.
.El
.Pp
The following are only provided by the
.Cd ar71xx_gpio
driver.
.Bl -tag -width ".Va hint.gpioiic.%d.atXXX"
.It Va hint.gpio.%d.pinmask
This is a bitmask of pins on the gpio board that we would like to expose
for use to the host o/s.
To expose pin 0, 4 and 7, use the bitmask of
10010001 converted to the hexadecimal value 0x0091.
.It Va hint.gpio.%d.pinon
This is a bitmask of pins on the gpio board that will be set to ON at host
start.
To set pin 2, 5 and 13 to be set ON at boot, use the bitmask of
10000000010010 converted to the hexadecimal value 0x2012.
.It Va hint.gpio.function_set
.It Va hint.gpio.function_clear
These are a bitmask of pins that will remap a pin to handle a specific
function (USB, UART TX/RX, etc) in the Atheros function registers.
This is mainly used to set/clear functions that we need when they are setup or
not setup by uBoot.
.El
.Pp
These values are configureable from the
.Xr gpioled 4
interface and help create
.Xr led 4
compatible devices in
.Pa /dev/led/<name> .
.Bl -tag -width ".Va hint.gpioiic.%d.atXXX"
.It Va hint.gpioled.%d.at
Normally assigned to gpiobus0.
.It Va hint.gpioled.%d.name
Arbitrary name of device in
.Pa /dev/led/
to create for
.Xr led 4
interfaces.
.It Va hint.gpioled.%d.pins
Which pin on the GPIO interface to map to this instance.
.El
.Pp
Simply put, each pin of the GPIO interface is connected to an input/output
of some device in a system.
.Sh SEE ALSO
.Xr iicbus 4 ,
.Xr gpioctl 8
.Sh HISTORY
The
.Nm
manual page first appeared in
.Fx 10.0 .
.Sh AUTHORS
This
manual page was written by
.An Sean Bruno Aq sbruno@FreeBSD.org .
|
