Configuring FAITH IPv6-to-IPv4 TCP relay Kazu Yamamoto and Jun-ichiro itojun Hagino $KAME: README,v 1.10 2003/01/06 21:40:33 sumikawa Exp $ $FreeBSD$ Introduction ============ FAITH is an IPv6-to-IPv4 TCP relay. It performs tcp relay just as some of firewall-oriented gateway does, but between IPv6 and IPv4 with address translation. TCP connections has to be made from IPv6 node to IPv4 node. FAITH will not relay connections for the opposite direction. To perform relays, FAITH daemon needs to be executed on a router between your local IPv6 site and outside IPv4 network. The daemon needs to be invoked per each TCP services (TCP port number). IPv4 node "dest" = 123.4.5.6 | [[[[ outside IPv4 ocean ]]]] | node that runs FAITH-daemon (usually a router) | ==+=====+===+==== IPv6, or IPv4/v6 network in your site ^ | | | connection clients IPv6 node "src" | You will have to allocate an IPv6 address prefix to map IPv4 addresses into. The following description uses 3ffe:0501:ffff:0000:: as example. Please use a prefix which belongs to your site. FAITH will make it possible to make an IPv6 TCP connection From IPv6 node "src", toward IPv4 node "dest", by specifying FAITH-mapped address 3ffe:0501:ffff:0000::123.4.5.6 (which is, 3ffe:0501:ffff:0000:0000:0000:7b04:0506). The address mapping can be performed by hand:-), by special nameserver on the network, or by special resolver on the source node. Setup ===== The following example assumes: - You have assigned 3ffe:0501:ffff:0000:: as FAITH adderss prefix. - You are willing to provide IPv6-to IPv4 TCP relay for telnet. <> (1) If you have IPv6 TCP server for the "telnet" service, i.e. telnetd via inet6d, disable that daemon. Comment out the line from "inet6d.conf" and send the HUP signal to "inet6d". (2) Execute sysctl as root to enable FAITH support in the kernel. # sysctl net.inet6.ip6.keepfaith=1 (3) Route packets toward FAITH prefix into "faith0" interface. # ifconfig faith0 up # route add -inet6 3ffe:0501:ffff:0000:: -prefixlen 64 ::1 # route change -inet6 3ffe:0501:ffff:0000:: -prefixlen 64 -ifp faith0 (4) Execute "faithd" by root as follows: # faithd telnet /usr/libexec/telnetd telnetd 1st argument is a service name you are willing to provide TCP relay. (it can be specified either by number "23" or by string "telnet") 2nd argument is a path name for local IPv6 TCP server. If there is a connection toward the router itself, this program will be invoked. 3rd and the following arguments are arguments for the local IPv6 TCP server. (3rd argument is typically the program name without its path.) More examples: # faithd ftpd /usr/libexec/ftpd ftpd -l # faithd sshd If inetd(8) on your platform have special support for faithd, it is possible to setup faithd services via inetd(8). Consult manpage for details. <> (4) Make sure that packets whose destinations match the prefix can reach from the IPv6 host to the translating router. <> There are two ways to translate IPv4 address to IPv6 address: (a) Faked by DNS (b) Faked by /etc/hosts. (5.a) Install "newbie" and set up FAITH mode. See kit/ports/newbie. (5.b) Add an entry into /etc/hosts so that you can resolve hostname into faked IPv6 addrss. For example, add the following line for www.netbsd.org: 3ffe:0501:ffff:0000::140.160.140.252 www.netbsd.org <> (6) To see if "faithd" works, watch "/var/log/daemon". Note: please setup "/etc/syslog.conf" so that LOG_DAEMON messages are to be stored in "/var/log/daemon". daemon.* /var/log/daemon Access control ============== Since faithd implements TCP relaying service, it is critical to implement proper access control to cope with malicious use. Bad guy may try to use your relay router to circumvent access controls, or may try to abuse your network (like sending SPAMs from IPv4 address that belong to you). Install IPv6 packet filter directives that would reject traffic from unwanted source. If you are using inetd-based setup, you may be able to use access control mechanisms in inetd. Advanced configuration ====================== If you would like to restrict IPv4 destination for translation, you may want to do the following: # route add -inet6 3ffe:0501:ffff:0000::123.0.0.0 -prefixlen 104 ::1 # route change -inet6 3ffe:0501:ffff:0000::123.0.0.0 -prefixlen 104 \ -ifp faith0 By this way, you can restrict IPv4 destination to 123.0.0.0/8. You may also want to reject packets toward 3ffe:0501:ffff:0000::/64 which is not in 3ffe:0501:ffff:0000::123.0.0.0/104. This will be left as excerside for the reader. By doing this, you will be able to provide your IPv4 web server to outside IPv6 customers, without risks of unwanted open relays. [[[[ IPv6 network outside ]]]] | | | connection node that runs FAITH-daemon (usually a router) v | ========+======== IPv4/v6 network in your site | (123.0.0.0/8) IPv4 web server