/* $FreeBSD$ */ /* $NetBSD: ieee80211_radiotap.h,v 1.16 2007/01/06 05:51:15 dyoung Exp $ */ /*- * Copyright (c) 2003, 2004 David Young. All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of David Young may not be used to endorse or promote * products derived from this software without specific prior * written permission. * * THIS SOFTWARE IS PROVIDED BY DAVID YOUNG ``AS IS'' AND ANY * EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, * THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A * PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL DAVID * YOUNG BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, * EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED * TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND * ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY * OF SUCH DAMAGE. */ #ifndef _NET80211_IEEE80211_RADIOTAP_H_ #define _NET80211_IEEE80211_RADIOTAP_H_ /* A generic radio capture format is desirable. It must be * rigidly defined (e.g., units for fields should be given), * and easily extensible. * * The following is an extensible radio capture format. It is * based on a bitmap indicating which fields are present. * * I am trying to describe precisely what the application programmer * should expect in the following, and for that reason I tell the * units and origin of each measurement (where it applies), or else I * use sufficiently weaselly language ("is a monotonically nondecreasing * function of...") that I cannot set false expectations for lawyerly * readers. */ #if defined(__KERNEL__) || defined(_KERNEL) #ifndef DLT_IEEE802_11_RADIO #define DLT_IEEE802_11_RADIO 127 /* 802.11 plus WLAN header */ #endif #endif /* defined(__KERNEL__) || defined(_KERNEL) */ #define IEEE80211_RADIOTAP_HDRLEN 64 /* XXX deprecated */ struct ieee80211_radiotap_vendor_header { uint8_t vh_oui[3]; /* 3 byte vendor OUI */ uint8_t vh_sub_ns; /* Sub namespace of this section */ uint16_t vh_skip_len; /* Length of this vendor section */ } __packed; /* * The radio capture header precedes the 802.11 header. * * Note well: all radiotap fields are little-endian. */ struct ieee80211_radiotap_header { uint8_t it_version; /* Version 0. Only increases * for drastic changes, * introduction of compatible * new fields does not count. */ uint8_t it_pad; uint16_t it_len; /* length of the whole * header in bytes, including * it_version, it_pad, * it_len, and data fields. */ uint32_t it_present; /* A bitmap telling which * fields are present. Set bit 31 * (0x80000000) to extend the * bitmap by another 32 bits. * Additional extensions are made * by setting bit 31. */ } __packed; /* * Name Data type Units * ---- --------- ----- * * IEEE80211_RADIOTAP_TSFT uint64_t microseconds * * Value in microseconds of the MAC's 64-bit 802.11 Time * Synchronization Function timer when the first bit of the * MPDU arrived at the MAC. For received frames, only. * * IEEE80211_RADIOTAP_CHANNEL 2 x uint16_t MHz, bitmap * * Tx/Rx frequency in MHz, followed by flags (see below). * * IEEE80211_RADIOTAP_FHSS uint16_t see below * * For frequency-hopping radios, the hop set (first byte) * and pattern (second byte). * * IEEE80211_RADIOTAP_RATE uint8_t 500kb/s or index * * Tx/Rx data rate. If bit 0x80 is set then it represents an * an MCS index and not an IEEE rate. * * IEEE80211_RADIOTAP_DBM_ANTSIGNAL int8_t decibels from * one milliwatt (dBm) * * RF signal power at the antenna, decibel difference from * one milliwatt. * * IEEE80211_RADIOTAP_DBM_ANTNOISE int8_t decibels from * one milliwatt (dBm) * * RF noise power at the antenna, decibel difference from one * milliwatt. * * IEEE80211_RADIOTAP_DB_ANTSIGNAL uint8_t decibel (dB) * * RF signal power at the antenna, decibel difference from an * arbitrary, fixed reference. * * IEEE80211_RADIOTAP_DB_ANTNOISE uint8_t decibel (dB) * * RF noise power at the antenna, decibel difference from an * arbitrary, fixed reference point. * * IEEE80211_RADIOTAP_LOCK_QUALITY uint16_t unitless * * Quality of Barker code lock. Unitless. Monotonically * nondecreasing with "better" lock strength. Called "Signal * Quality" in datasheets. (Is there a standard way to measure * this?) * * IEEE80211_RADIOTAP_TX_ATTENUATION uint16_t unitless * * Transmit power expressed as unitless distance from max * power set at factory calibration. 0 is max power. * Monotonically nondecreasing with lower power levels. * * IEEE80211_RADIOTAP_DB_TX_ATTENUATION uint16_t decibels (dB) * * Transmit power expressed as decibel distance from max power * set at factory calibration. 0 is max power. Monotonically * nondecreasing with lower power levels. * * IEEE80211_RADIOTAP_DBM_TX_POWER int8_t decibels from * one milliwatt (dBm) * * Transmit power expressed as dBm (decibels from a 1 milliwatt * reference). This is the absolute power level measured at * the antenna port. * * IEEE80211_RADIOTAP_FLAGS uint8_t bitmap * * Properties of transmitted and received frames. See flags * defined below. * * IEEE80211_RADIOTAP_ANTENNA uint8_t antenna index * * Unitless indication of the Rx/Tx antenna for this packet. * The first antenna is antenna 0. * * IEEE80211_RADIOTAP_XCHANNEL uint32_t bitmap * uint16_t MHz * uint8_t channel number * int8_t .5 dBm * * Extended channel specification: flags (see below) followed by * frequency in MHz, the corresponding IEEE channel number, and * finally the maximum regulatory transmit power cap in .5 dBm * units. This property supersedes IEEE80211_RADIOTAP_CHANNEL * and only one of the two should be present. */ enum ieee80211_radiotap_type { IEEE80211_RADIOTAP_TSFT = 0, IEEE80211_RADIOTAP_FLAGS = 1, IEEE80211_RADIOTAP_RATE = 2, IEEE80211_RADIOTAP_CHANNEL = 3, IEEE80211_RADIOTAP_FHSS = 4, IEEE80211_RADIOTAP_DBM_ANTSIGNAL = 5, IEEE80211_RADIOTAP_DBM_ANTNOISE = 6, IEEE80211_RADIOTAP_LOCK_QUALITY = 7, IEEE80211_RADIOTAP_TX_ATTENUATION = 8, IEEE80211_RADIOTAP_DB_TX_ATTENUATION = 9, IEEE80211_RADIOTAP_DBM_TX_POWER = 10, IEEE80211_RADIOTAP_ANTENNA = 11, IEEE80211_RADIOTAP_DB_ANTSIGNAL = 12, IEEE80211_RADIOTAP_DB_ANTNOISE = 13, /* * 14-17 are from Linux, they overlap the netbsd-specific * fields. */ IEEE80211_RADIOTAP_RX_FLAGS = 14, IEEE80211_RADIOTAP_TX_FLAGS = 15, IEEE80211_RADIOTAP_RTS_RETRIES = 16, IEEE80211_RADIOTAP_DATA_RETRIES = 17, IEEE80211_RADIOTAP_XCHANNEL = 18, IEEE80211_RADIOTAP_MCS = 19, IEEE80211_RADIOTAP_AMPDU_STATUS = 20, IEEE80211_RADIOTAP_RADIOTAP_NAMESPACE = 29, IEEE80211_RADIOTAP_VENDOREXT = 30, IEEE80211_RADIOTAP_EXT = 31, }; #ifndef _KERNEL /* channel attributes */ #define IEEE80211_CHAN_TURBO 0x00000010 /* Turbo channel */ #define IEEE80211_CHAN_CCK 0x00000020 /* CCK channel */ #define IEEE80211_CHAN_OFDM 0x00000040 /* OFDM channel */ #define IEEE80211_CHAN_2GHZ 0x00000080 /* 2 GHz spectrum channel. */ #define IEEE80211_CHAN_5GHZ 0x00000100 /* 5 GHz spectrum channel */ #define IEEE80211_CHAN_PASSIVE 0x00000200 /* Only passive scan allowed */ #define IEEE80211_CHAN_DYN 0x00000400 /* Dynamic CCK-OFDM channel */ #define IEEE80211_CHAN_GFSK 0x00000800 /* GFSK channel (FHSS PHY) */ #define IEEE80211_CHAN_GSM 0x00001000 /* 900 MHz spectrum channel */ #define IEEE80211_CHAN_STURBO 0x00002000 /* 11a static turbo channel only */ #define IEEE80211_CHAN_HALF 0x00004000 /* Half rate channel */ #define IEEE80211_CHAN_QUARTER 0x00008000 /* Quarter rate channel */ #endif /* !_KERNEL */ /* For IEEE80211_RADIOTAP_FLAGS */ #define IEEE80211_RADIOTAP_F_CFP 0x01 /* sent/received * during CFP */ #define IEEE80211_RADIOTAP_F_SHORTPRE 0x02 /* sent/received * with short * preamble */ #define IEEE80211_RADIOTAP_F_WEP 0x04 /* sent/received * with WEP encryption */ #define IEEE80211_RADIOTAP_F_FRAG 0x08 /* sent/received * with fragmentation */ #define IEEE80211_RADIOTAP_F_FCS 0x10 /* frame includes FCS */ #define IEEE80211_RADIOTAP_F_DATAPAD 0x20 /* frame has padding between * 802.11 header and payload * (to 32-bit boundary) */ #define IEEE80211_RADIOTAP_F_BADFCS 0x40 /* does not pass FCS check */ #define IEEE80211_RADIOTAP_F_SHORTGI 0x80 /* HT short GI */ #endif /* !_NET80211_IEEE80211_RADIOTAP_H_ */