/* * Generic driver for the aic7xxx based adaptec SCSI controllers * Product specific probe and attach routines can be found in: * i386/eisa/aic7770.c 27/284X and aic7770 motherboard controllers * pci/aic7870.c 3940, 2940, aic7880, aic7870, aic7860, * and aic7850 controllers * * Copyright (c) 1994, 1995, 1996, 1997 Justin T. Gibbs. * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice immediately at the beginning of the file, without modification, * this list of conditions, and the following disclaimer. * 2. Redistributions in binary form must reproduce the above copyright * notice, this list of conditions and the following disclaimer in the * documentation and/or other materials provided with the distribution. * 3. The name of the author may not be used to endorse or promote products * derived from this software without specific prior written permission. * * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF * SUCH DAMAGE. * * $Id: aic7xxx.c,v 1.116 1997/04/14 02:27:50 gibbs Exp $ */ /* * TODO: * Implement Target Mode * * A few notes on features of the driver. * * SCB paging takes advantage of the fact that devices stay disconnected * from the bus a relatively long time and that while they're disconnected, * having the SCBs for these transactions down on the host adapter is of * little use. Instead of leaving this idle SCB down on the card we copy * it back up into kernel memory and reuse the SCB slot on the card to * schedule another transaction. This can be a real payoff when doing random * I/O to tagged queueing devices since there are more transactions active at * once for the device to sort for optimal seek reduction. The algorithm goes * like this... * * The sequencer maintains two lists of its hardware SCBs. The first is the * singly linked free list which tracks all SCBs that are not currently in * use. The second is the doubly linked disconnected list which holds the * SCBs of transactions that are in the disconnected state sorted most * recently disconnected first. When the kernel queues a transaction to * the card, a hardware SCB to "house" this transaction is retrieved from * either of these two lists. If the SCB came from the disconnected list, * a check is made to see if any data transfer or SCB linking (more on linking * in a bit) information has been changed since it was copied from the host * and if so, DMAs the SCB back up before it can be used. Once a hardware * SCB has been obtained, the SCB is DMAed from the host. Before any work * can begin on this SCB, the sequencer must ensure that either the SCB is * for a tagged transaction or the target is not already working on another * non-tagged transaction. If a conflict arises in the non-tagged case, the * sequencer finds the SCB for the active transactions and sets the SCB_LINKED * field in that SCB to this next SCB to execute. To facilitate finding * active non-tagged SCBs, the last four bytes of up to the first four hardware * SCBs serve as a storage area for the currently active SCB ID for each * target. * * When a device reconnects, a search is made of the hardware SCBs to find * the SCB for this transaction. If the search fails, a hardware SCB is * pulled from either the free or disconnected SCB list and the proper * SCB is DMAed from the host. If the SCB_ABORTED control bit is set * in the control byte of the SCB while it was disconnected, the sequencer * will send an abort or abort tag message to the target during the * reconnection and signal the kernel that the abort was successfull. * * When a command completes, a check for non-zero status and residuals is * made. If either of these conditions exists, the SCB is DMAed back up to * the host so that it can interpret this information. Additionally, in the * case of bad status, the sequencer generates a special interrupt and pauses * itself. This allows the host to setup a request sense command if it * chooses for this target synchronously with the error so that sense * information isn't lost. * */ #include #include #if defined(__NetBSD__) #include #include #include #endif /* defined(__NetBSD__) */ #include #include #include #include #include #if defined(__NetBSD__) #include #endif #include #include #if defined(__FreeBSD__) #include #endif #include #include #include #if defined(__FreeBSD__) #include #include #include #include #endif /* defined(__FreeBSD__) */ #if defined(__NetBSD__) #include #include #define bootverbose 1 #if DEBUGTARGET < 0 /* Negative numbers for disabling cause warnings */ #define DEBUGTARGET 17 #endif #endif /* defined(__NetBSD__) */ #include #define MAX(a,b) (((a) > (b)) ? (a) : (b)) #define MIN(a,b) (((a) < (b)) ? (a) : (b)) #define ALL_TARGETS -1 #define ALL_LUNS -1 #define ALL_CHANNELS '\0' #if defined(__FreeBSD__) u_long ahc_unit = 0; #endif #ifdef AHC_DEBUG static int ahc_debug = AHC_DEBUG; #endif #ifdef AHC_BROKEN_CACHE int ahc_broken_cache = 1; /* * "wbinvd" cause writing back whole cache (both CPU internal & external) * to memory, so that the instruction takes a lot of time. * This makes machine slow. */ #define INVALIDATE_CACHE() __asm __volatile("wbinvd") #endif /**** bit definitions for SCSIDEF ****/ #define HSCSIID 0x07 /* our SCSI ID */ #define HWSCSIID 0x0f /* our SCSI ID if Wide Bus */ static void ahcminphys __P((struct buf *bp)); static int32_t ahc_scsi_cmd __P((struct scsi_xfer *xs)); static void ahc_run_waiting_queue __P((struct ahc_softc *ahc)); static struct scb * ahc_get_scb __P((struct ahc_softc *ahc, u_int32_t flags)); static void ahc_free_scb __P((struct ahc_softc *ahc, struct scb *scb)); static struct scb * ahc_alloc_scb __P((struct ahc_softc *ahc)); static inline void pause_sequencer __P((struct ahc_softc *ahc)); static inline void unpause_sequencer __P((struct ahc_softc *ahc, int unpause_always)); static inline void restart_sequencer __P((struct ahc_softc *ahc)); static int timeouts_work; /* * Boolean that lets the driver know * that it can safely use timeouts * for event scheduling. Timeouts * don't work early in the boot * process. */ #define AHC_BUSRESET_DELAY 1000 /* Reset delay in us */ #define AHC_BUSSETTLE_DELAY (100 * 1000)/* Delay before taking commands * after a reset in us */ static struct scsi_adapter ahc_switch = { ahc_scsi_cmd, ahcminphys, NULL, NULL, #if defined(__FreeBSD__) NULL, "ahc", { 0, 0 } #endif }; static struct scsi_device ahc_dev = { NULL, /* Use default error handler */ NULL, /* have a queue, served by this */ NULL, /* have no async handler */ NULL, /* Use default 'done' routine */ #if defined(__FreeBSD__) "ahc", 0, { 0, 0 } #endif }; static inline void pause_sequencer(ahc) struct ahc_softc *ahc; { ahc_outb(ahc, HCNTRL, ahc->pause); /* * Since the sequencer can disable pausing in a critical section, we * must loop until it actually stops. */ while ((ahc_inb(ahc, HCNTRL) & PAUSE) == 0) ; } static inline void unpause_sequencer(ahc, unpause_always) struct ahc_softc *ahc; int unpause_always; { if (unpause_always || (ahc_inb(ahc, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) == 0) ahc_outb(ahc, HCNTRL, ahc->unpause); } /* * Restart the sequencer program from address zero */ static inline void restart_sequencer(ahc) struct ahc_softc *ahc; { do { ahc_outb(ahc, SEQCTL, SEQRESET|FASTMODE); } while ((ahc_inb(ahc, SEQADDR0) != 0) || (ahc_inb(ahc, SEQADDR1) != 0)); unpause_sequencer(ahc, /*unpause_always*/TRUE); } #if defined(__FreeBSD__) #define IS_SCSIBUS_B(ahc, sc_link) \ (((u_int32_t)((sc_link)->fordriver) & SELBUSB) != 0) #else /* NetBSD/OpenBSD */ #define IS_SCSIBUS_B(ahc, sc_link) \ ((sc_link)->scsibus == (ahc)->sc_link_b.scsibus) #endif #define SCB_TARGET(scb) \ (((scb)->hscb->tcl & TID) >> 4) #define SCB_LUN(scb) \ ((scb)->hscb->tcl & LID) #define SCB_IS_SCSIBUS_B(scb) \ (((scb)->hscb->tcl & SELBUSB) != 0) static u_int8_t ahc_abort_wscb __P((struct ahc_softc *ahc, struct scb *scbp, u_int8_t scbpos, u_int8_t prev, u_int32_t xs_error)); static void ahc_done __P((struct ahc_softc *ahc, struct scb *scbp)); static void ahc_handle_seqint __P((struct ahc_softc *ahc, u_int8_t intstat)); static void ahc_handle_scsiint __P((struct ahc_softc *ahc, u_int8_t intstat)); static void ahc_handle_devreset __P((struct ahc_softc *ahc, int target, char channel)); static void ahc_loadseq __P((struct ahc_softc *ahc)); static struct patch * ahc_next_patch __P((struct patch *cur_patch, int options, int instrptr)); static void ahc_download_instr __P((struct ahc_softc *ahc, int options, int instrptr)); static int ahc_match_scb __P((struct scb *scb, int target, char channel, int lun, u_int8_t tag)); static int ahc_poll __P((struct ahc_softc *ahc, int wait)); #ifdef AHC_DEBUG static void ahc_print_scb __P((struct scb *scb)); #endif static u_int8_t ahc_find_scb __P((struct ahc_softc *ahc, struct scb *scb)); static int ahc_search_qinfifo __P((struct ahc_softc *ahc, int target, char channel, int lun, u_int8_t tag, u_int32_t flags, u_int32_t xs_error, int requeue)); static int ahc_reset_channel __P((struct ahc_softc *ahc, char channel, u_int32_t xs_error, int initiate_reset)); static int ahc_reset_device __P((struct ahc_softc *ahc, int target, char channel, int lun, u_int8_t tag, u_int32_t xs_error)); static u_int8_t ahc_rem_scb_from_disc_list __P((struct ahc_softc *ahc, u_int8_t scbptr)); static void ahc_add_curscb_to_free_list __P((struct ahc_softc *ahc)); static void ahc_clear_intstat __P((struct ahc_softc *ahc)); static void ahc_reset_current_bus __P((struct ahc_softc *ahc)); static void ahc_run_done_queue __P((struct ahc_softc *ahc)); static void ahc_untimeout_done_queue __P((struct ahc_softc *ahc)); static void ahc_scsirate __P((struct ahc_softc* ahc, u_int8_t *scsirate, u_int8_t *period, u_int8_t *offset, char channel, int target)); #if defined(__FreeBSD__) static timeout_t ahc_timeout; #elif defined(__NetBSD__) static void ahc_timeout __P((void *)); #endif static timeout_t ahc_first_timeout; static timeout_t ahc_busreset_complete; static timeout_t ahc_busreset_settle_complete; static u_int8_t ahc_index_busy_target __P((struct ahc_softc *ahc, int target, char channel, int unbusy)); static void ahc_busy_target __P((struct ahc_softc *ahc, int target, char channel, u_int8_t scbid)); static void ahc_construct_sdtr __P((struct ahc_softc *ahc, int start_byte, u_int8_t period, u_int8_t offset)); static void ahc_construct_wdtr __P((struct ahc_softc *ahc, int start_byte, u_int8_t bus_width)); static void ahc_calc_residual __P((struct scb *scb)); #if defined(__FreeBSD__) char *ahc_name(ahc) struct ahc_softc *ahc; { static char name[10]; sprintf(name, "ahc%d", ahc->unit); return (name); } #elif defined(__NetBSD__) struct cfdriver ahc_cd = { NULL, "ahc", DV_DULL }; #endif #ifdef AHC_DEBUG static void ahc_print_scb(scb) struct scb *scb; { struct hardware_scb *hscb = scb->hscb; printf("scb:%p control:0x%x tcl:0x%x cmdlen:%d cmdpointer:0x%lx\n", scb, hscb->control, hscb->tcl, hscb->cmdlen, hscb->cmdpointer ); printf(" datlen:%d data:0x%lx segs:0x%x segp:0x%lx\n", hscb->datalen, hscb->data, hscb->SG_segment_count, hscb->SG_list_pointer); printf(" sg_addr:%lx sg_len:%ld\n", hscb->ahc_dma[0].addr, hscb->ahc_dma[0].len); } #endif static struct { u_int8_t errno; char *errmesg; } hard_error[] = { { ILLHADDR, "Illegal Host Access" }, { ILLSADDR, "Illegal Sequencer Address referrenced" }, { ILLOPCODE, "Illegal Opcode in sequencer program" }, { PARERR, "Sequencer Ram Parity Error" } }; /* * Valid SCSIRATE values. (p. 3-17) * Provides a mapping of tranfer periods in ns to the proper value to * stick in the scsiscfr reg to use that transfer rate. */ static struct { int sxfr; /* Rates in Ultra mode have bit 8 of sxfr set */ #define ULTRA_SXFR 0x100 u_int8_t period; /* Period to send to SCSI target */ char *rate; } ahc_syncrates[] = { { 0x100, 12, "20.0" }, { 0x110, 15, "16.0" }, { 0x120, 18, "13.4" }, { 0x000, 25, "10.0" }, { 0x010, 31, "8.0" }, { 0x020, 37, "6.67" }, { 0x030, 43, "5.7" }, { 0x040, 50, "5.0" }, { 0x050, 56, "4.4" }, { 0x060, 62, "4.0" }, { 0x070, 68, "3.6" } }; static int ahc_num_syncrates = sizeof(ahc_syncrates) / sizeof(ahc_syncrates[0]); /* * Allocate a controller structure for a new device and initialize it. */ #if defined(__FreeBSD__) struct ahc_softc * ahc_alloc(unit, iobase, maddr, type, flags, scb_data) int unit; u_int32_t iobase; #elif defined(__NetBSD__) void ahc_construct(ahc, bc, ioh, maddr, type, flags) struct ahc_softc *ahc; bus_chipset_tag_t bc; bus_io_handle_t ioh; #endif vm_offset_t maddr; ahc_type type; ahc_flag flags; struct scb_data *scb_data; { /* * find unit and check we have that many defined */ #if defined(__FreeBSD__) struct ahc_softc *ahc; size_t alloc_size; /* * Allocate a storage area for us */ if (scb_data == NULL) /* * We are not sharing SCB space with another controller * so allocate our own SCB data space. */ alloc_size = sizeof(struct full_ahc_softc); else alloc_size = sizeof(struct ahc_softc); ahc = malloc(alloc_size, M_DEVBUF, M_NOWAIT); if (!ahc) { printf("ahc%d: cannot malloc!\n", unit); return NULL; } bzero(ahc, alloc_size); #endif if (scb_data == NULL) { struct full_ahc_softc* full_softc = (struct full_ahc_softc*)ahc; ahc->scb_data = &full_softc->scb_data_storage; STAILQ_INIT(&ahc->scb_data->free_scbs); } else ahc->scb_data = scb_data; STAILQ_INIT(&ahc->waiting_scbs); #if defined(__FreeBSD__) ahc->unit = unit; #endif #if defined(__FreeBSD__) ahc->baseport = iobase; #elif defined(__NetBSD__) ahc->sc_bc = bc; ahc->sc_ioh = ioh; #endif ahc->maddr = (volatile u_int8_t *)maddr; ahc->type = type; ahc->flags = flags; ahc->unpause = (ahc_inb(ahc, HCNTRL) & IRQMS) | INTEN; ahc->pause = ahc->unpause | PAUSE; ahc->busreset_args.ahc = ahc; ahc->busreset_args.bus = 'A'; ahc->busreset_args_b.ahc = ahc; ahc->busreset_args_b.bus = 'B'; #if defined(__FreeBSD__) return (ahc); #endif } void ahc_free(ahc) struct ahc_softc *ahc; { #if defined(__FreeBSD__) free(ahc, M_DEVBUF); return; #endif } void ahc_reset(ahc) struct ahc_softc *ahc; { u_int8_t hcntrl; int wait; /* Retain the IRQ type accross the chip reset */ hcntrl = (ahc_inb(ahc, HCNTRL) & IRQMS) | INTEN; ahc_outb(ahc, HCNTRL, CHIPRST | PAUSE); /* * Ensure that the reset has finished */ wait = 1000; while (--wait && !(ahc_inb(ahc, HCNTRL) & CHIPRSTACK)) DELAY(1000); if (wait == 0) { printf("%s: WARNING - Failed chip reset! " "Trying to initialize anyway.\n", ahc_name(ahc)); } ahc_outb(ahc, HCNTRL, hcntrl | PAUSE); } /* * Look up the valid period to SCSIRATE conversion in our table. */ static void ahc_scsirate(ahc, scsirate, period, offset, channel, target ) struct ahc_softc *ahc; u_int8_t *scsirate; u_int8_t *period; u_int8_t *offset; char channel; int target; { int i; u_int32_t ultra_enb_addr; u_int8_t sxfrctl0; u_int8_t ultra_enb; i = ahc_num_syncrates; /* Default to async */ if (*period >= ahc_syncrates[0].period && *offset != 0) { for (i = 0; i < ahc_num_syncrates; i++) { if (*period <= ahc_syncrates[i].period) { /* * Watch out for Ultra speeds when ultra is not * enabled and vice-versa. */ if (!(ahc->type & AHC_ULTRA) && (ahc_syncrates[i].sxfr & ULTRA_SXFR)) { /* * This should only happen if the * drive is the first to negotiate * and chooses a high rate. We'll * just move down the table util * we hit a non ultra speed. */ continue; } *scsirate = (ahc_syncrates[i].sxfr & 0xF0) | (*offset & 0x0f); *period = ahc_syncrates[i].period; if (bootverbose) { printf("%s: target %d synchronous at " "%sMHz, offset = 0x%x\n", ahc_name(ahc), target, ahc_syncrates[i].rate, *offset ); } break; } } } if (i >= ahc_num_syncrates) { /* Use asynchronous transfers. */ *scsirate = 0; *period = 0; *offset = 0; if (bootverbose) printf("%s: target %d using asynchronous transfers\n", ahc_name(ahc), target ); } /* * Ensure Ultra mode is set properly for * this target. */ ultra_enb_addr = ULTRA_ENB; if (channel == 'B' || target > 7) ultra_enb_addr++; ultra_enb = ahc_inb(ahc, ultra_enb_addr); sxfrctl0 = ahc_inb(ahc, SXFRCTL0); if (*scsirate != 0 && ahc_syncrates[i].sxfr & ULTRA_SXFR) { ultra_enb |= 0x01 << (target & 0x07); sxfrctl0 |= FAST20; } else { ultra_enb &= ~(0x01 << (target & 0x07)); sxfrctl0 &= ~FAST20; } ahc_outb(ahc, ultra_enb_addr, ultra_enb); ahc_outb(ahc, SXFRCTL0, sxfrctl0); } #if defined(__NetBSD__) int ahcprint(aux, name) void *aux; char *name; { if (name != NULL) printf("%s: scsibus ", name); return UNCONF; } #endif /* * Attach all the sub-devices we can find */ int ahc_attach(ahc) struct ahc_softc *ahc; { struct scsibus_data *scbus; #ifdef AHC_BROKEN_CACHE if (cpu_class == CPUCLASS_386) /* doesn't have "wbinvd" instruction */ ahc_broken_cache = 0; #endif /* * fill in the prototype scsi_links. */ #if defined(__FreeBSD__) ahc->sc_link.adapter_unit = ahc->unit; ahc->sc_link.adapter_targ = ahc->our_id; ahc->sc_link.fordriver = 0; #elif defined(__NetBSD__) ahc->sc_link.adapter_target = ahc->our_id; #endif ahc->sc_link.adapter_softc = ahc; ahc->sc_link.adapter = &ahc_switch; ahc->sc_link.opennings = 2; ahc->sc_link.device = &ahc_dev; ahc->sc_link.flags = DEBUGLEVEL; if (ahc->type & AHC_TWIN) { /* Configure the second scsi bus */ ahc->sc_link_b = ahc->sc_link; #if defined(__FreeBSD__) ahc->sc_link_b.adapter_targ = ahc->our_id_b; ahc->sc_link_b.adapter_bus = 1; ahc->sc_link_b.fordriver = (void *)SELBUSB; #elif defined(__NetBSD__) ahc->sc_link_b.adapter_target = ahc->our_id_b; #endif } #if defined(__FreeBSD__) /* * Prepare the scsibus_data area for the upperlevel * scsi code. */ scbus = scsi_alloc_bus(); if(!scbus) return 0; scbus->adapter_link = (ahc->flags & AHC_CHANNEL_B_PRIMARY) ? &ahc->sc_link_b : &ahc->sc_link; if (ahc->type & AHC_WIDE) scbus->maxtarg = 15; /* * ask the adapter what subunits are present */ if (bootverbose) printf("ahc%d: Probing channel %c\n", ahc->unit, (ahc->flags & AHC_CHANNEL_B_PRIMARY) ? 'B' : 'A'); scsi_attachdevs(scbus); scbus = NULL; /* Upper-level SCSI code owns this now */ if (ahc->type & AHC_TWIN) { scbus = scsi_alloc_bus(); if (!scbus) return 0; scbus->adapter_link = (ahc->flags & AHC_CHANNEL_B_PRIMARY) ? &ahc->sc_link : &ahc->sc_link_b; if (ahc->type & AHC_WIDE) scbus->maxtarg = 15; if (bootverbose) printf("ahc%d: Probing Channel %c\n", ahc->unit, (ahc->flags & AHC_CHANNEL_B_PRIMARY) ? 'A': 'B'); scsi_attachdevs(scbus); scbus = NULL; /* Upper-level SCSI code owns this now */ } #elif defined(__NetBSD__) /* * XXX - Update MI SCSI code * * if(ahc->type & AHC_WIDE) * max target of both channel A and B = 15; */ /* * ask the adapter what subunits are present */ if ((ahc->flags & AHC_CHANNEL_B_PRIMARY) == 0) { /* make IS_SCSIBUS_B() == false, while probing channel A */ ahc->sc_link_b.scsibus = 0xff; if (ahc->type & AHC_TWIN) printf("%s: Probing channel A\n", ahc_name(ahc)); config_found((void *)ahc, &ahc->sc_link, ahcprint); if (ahc->type & AHC_TWIN) { printf("%s: Probing channel B\n", ahc_name(ahc)); config_found((void *)ahc, &ahc->sc_link_b, ahcprint); } } else { /* * if implementation of IS_SCSIBUS_B() is changed to use * ahc->sc_link.scsibus, then "ahc->sc_link.scsibus = 0xff;" * is needed, here. */ /* assert(ahc->type & AHC_TWIN); */ printf("%s: Probing channel B\n", ahc_name(ahc)); config_found((void *)ahc, &ahc->sc_link_b, ahcprint); printf("%s: Probing channel A\n", ahc_name(ahc)); config_found((void *)ahc, &ahc->sc_link, ahcprint); } #endif return 1; } /* * Catch an interrupt from the adapter */ #if defined(__FreeBSD__) void #elif defined (__NetBSD__) int #endif ahc_intr(arg) void *arg; { struct ahc_softc *ahc; u_int8_t intstat; ahc = (struct ahc_softc *)arg; intstat = ahc_inb(ahc, INTSTAT); /* * Is this interrupt for me? or for * someone who is sharing my interrupt? */ if (!(intstat & INT_PEND)) #if defined(__FreeBSD__) return; #elif defined(__NetBSD__) return 0; #endif if (intstat & CMDCMPLT) { struct scb *scb; u_int8_t scb_index; u_int8_t qoutcnt; int int_cleared; int_cleared = 0; while (qoutcnt = (ahc_inb(ahc, QOUTCNT) & ahc->qcntmask)) { for (; qoutcnt > 0; qoutcnt--) { scb_index = ahc_inb(ahc, QOUTFIFO); scb = ahc->scb_data->scbarray[scb_index]; if (!scb || !(scb->flags & SCB_ACTIVE)) { printf("%s: WARNING " "no command for scb %d " "(cmdcmplt)\nQOUTCNT == %d\n", ahc_name(ahc), scb_index, qoutcnt); continue; } /* * Save off the residual if there is one. */ if (scb->hscb->residual_SG_segment_count != 0) ahc_calc_residual(scb); if ((scb->flags & SCB_QUEUED_ABORT) != 0) { /* Have to clean up any possible * entries in the waiting queue and * QINFIFO. */ int target; char channel; int lun; u_int8_t tag; tag = SCB_LIST_NULL; target = scb->xs->sc_link->target; lun = scb->xs->sc_link->lun; channel = (scb->hscb->tcl & SELBUSB) ? 'B': 'A'; if (scb->hscb->control & TAG_ENB) tag = scb->hscb->tag; ahc_reset_device(ahc, target, channel, lun, tag, scb->xs->error); ahc_run_done_queue(ahc); } ahc_done(ahc, scb); } ahc_outb(ahc, CLRINT, CLRCMDINT); int_cleared++; } if (int_cleared == 0) ahc_outb(ahc, CLRINT, CLRCMDINT); } if (intstat & BRKADRINT) { /* * We upset the sequencer :-( * Lookup the error message */ int i, error, num_errors; error = ahc_inb(ahc, ERROR); num_errors = sizeof(hard_error)/sizeof(hard_error[0]); for (i = 0; error != 1 && i < num_errors; i++) error >>= 1; printf("%s: brkadrint, %s at seqaddr = 0x%x\n", ahc_name(ahc), hard_error[i].errmesg, (ahc_inb(ahc, SEQADDR1) << 8) | ahc_inb(ahc, SEQADDR0)); ahc_reset_device(ahc, ALL_TARGETS, ALL_CHANNELS, ALL_LUNS, SCB_LIST_NULL, XS_DRIVER_STUFFUP); ahc_run_done_queue(ahc); } if (intstat & SEQINT) ahc_handle_seqint(ahc, intstat); if (intstat & SCSIINT) ahc_handle_scsiint(ahc, intstat); if (ahc->waiting_scbs.stqh_first != NULL) ahc_run_waiting_queue(ahc); #if defined(__NetBSD__) return 1; #endif } static void ahc_handle_seqint(ahc, intstat) struct ahc_softc *ahc; u_int8_t intstat; { struct scb *scb; u_int16_t targ_mask; u_int8_t target; int scratch_offset; char channel; if ((ahc_inb(ahc, SEQ_FLAGS) & RESELECTED) != 0) target = ahc_inb(ahc, SELID); else target = ahc_inb(ahc, SCSIID); target = (target >> 4) & 0x0f; scratch_offset = target; channel = ahc_inb(ahc, SBLKCTL) & SELBUSB ? 'B': 'A'; if (channel == 'B') scratch_offset += 8; targ_mask = (0x01 << scratch_offset); switch (intstat & SEQINT_MASK) { case NO_MATCH: { /* * This could be for a normal abort request. * Figure out the SCB that we were trying to find * and only give an error if we didn't ask for this * to happen. */ u_int8_t scb_index; u_int8_t busy_scbid; u_int8_t arg1; busy_scbid = ahc_index_busy_target(ahc, target, channel, /*unbusy*/FALSE); arg1 = ahc_inb(ahc, ARG_1); if (arg1 == SCB_LIST_NULL) /* Untagged Request */ scb_index = busy_scbid; else scb_index = arg1; if (scb_index < ahc->scb_data->numscbs) { scb = ahc->scb_data->scbarray[scb_index]; if (scb->hscb->control & ABORT_SCB) { /* * We expected this. Let the busfree * handler take care of this when we * the abort is finially sent. * Set IDENTIFY_SEEN so that the busfree * handler knows that there is an SCB to * cleanup. */ ahc_outb(ahc, SEQ_FLAGS, ahc_inb(ahc, SEQ_FLAGS) | IDENTIFY_SEEN); sc_print_addr(scb->xs->sc_link); printf("reconnect SCB abort successfull\n"); break; } } printf("%s:%c:%d: no active SCB for reconnecting " "target - issuing BUS DEVICE RESET\n", ahc_name(ahc), channel, target); printf("SAVED_TCL == 0x%x ARG_1 == 0x%x SEQADDR == 0x%x\n", ahc_inb(ahc, SAVED_TCL), arg1, (ahc_inb(ahc, SEQADDR1) << 8) | ahc_inb(ahc, SEQADDR0)); ahc_handle_devreset(ahc, target, channel); break; } case NO_MATCH_BUSY: { /* * XXX Leave this as a panic for the time being since * it indicates a bug in the timeout code for this * to happen. */ u_int8_t scb_index; u_int8_t busy_scbindex; scb_index = ahc_inb(ahc, CUR_SCBID); scb = ahc->scb_data->scbarray[scb_index]; panic("%s:%c:%d: Target busy link failure.\n", ahc_name(ahc), (scb->hscb->tcl & SELBUSB) ? 'B' : 'A', scb->xs->sc_link->target); } case SEND_REJECT: { u_int8_t rejbyte = ahc_inb(ahc, REJBYTE); printf("%s:%c:%d: Warning - unknown message received from " "target (0x%x). Rejecting\n", ahc_name(ahc), channel, target, rejbyte); break; } case NO_IDENT: { /* * The reconnecting target either did not send an identify * message, or did, but we didn't find and SCB to match and * before it could respond to our ATN/abort, it hit a dataphase. * The only safe thing to do is to blow it away with a bus * reset. */ int found; printf("%s:%c:%d: Target did not send an IDENTIFY message. " "LASTPHASE = 0x%x, SAVED_TCL == 0x%x\n", ahc_name(ahc), channel, target, ahc_inb(ahc, LASTPHASE), ahc_inb(ahc, SAVED_TCL)); found = ahc_reset_channel(ahc, channel, XS_TIMEOUT, /*initiate reset*/TRUE); printf("%s: Issued Channel %c Bus Reset. " "%d SCBs aborted\n", ahc_name(ahc), channel, found); break; } case BAD_PHASE: if (ahc_inb(ahc, LASTPHASE) == P_BUSFREE) { printf("%s:%c:%d: Missed busfree.\n", ahc_name(ahc), channel, target); restart_sequencer(ahc); } else { printf("%s:%c:%d: unknown scsi bus phase. Attempting " "to continue\n", ahc_name(ahc), channel, target); } break; case EXTENDED_MSG: { u_int8_t message_length; u_int8_t message_code; u_int8_t scb_index; message_length = ahc_inb(ahc, MSGIN_EXT_LEN); message_code = ahc_inb(ahc, MSGIN_EXT_OPCODE); scb_index = ahc_inb(ahc, SCB_TAG); scb = ahc->scb_data->scbarray[scb_index]; switch (message_code) { case MSG_EXT_SDTR: { u_int8_t period; u_int8_t offset; u_int8_t saved_offset; u_int8_t targ_scratch; u_int8_t maxoffset; u_int8_t rate; if (message_length != MSG_EXT_SDTR_LEN) { ahc_outb(ahc, RETURN_1, SEND_REJ); break; } period = ahc_inb(ahc, MSGIN_EXT_BYTES); saved_offset = ahc_inb(ahc, MSGIN_EXT_BYTES + 1); targ_scratch = ahc_inb(ahc, TARG_SCRATCH + scratch_offset); if (targ_scratch & WIDEXFER) maxoffset = MAX_OFFSET_16BIT; else maxoffset = MAX_OFFSET_8BIT; offset = MIN(saved_offset, maxoffset); ahc_scsirate(ahc, &rate, &period, &offset, channel, target); /* Preserve the WideXfer flag */ targ_scratch = rate | (targ_scratch & WIDEXFER); /* * Update both the target scratch area and the * current SCSIRATE. */ ahc_outb(ahc, TARG_SCRATCH + scratch_offset, targ_scratch); ahc_outb(ahc, SCSIRATE, targ_scratch); /* * See if we initiated Sync Negotiation * and didn't have to fall down to async * transfers. */ if ((scb->flags & SCB_MSGOUT_SDTR) != 0) { /* We started it */ if (saved_offset == offset) { /* * Don't send an SDTR back to * the target */ ahc_outb(ahc, RETURN_1, 0); } else /* Went too low - force async */ ahc_outb(ahc, RETURN_1, SEND_REJ); } else { /* * Send our own SDTR in reply */ printf("Sending SDTR!!\n"); ahc_construct_sdtr(ahc, /*start_byte*/0, period, offset); ahc_outb(ahc, RETURN_1, SEND_MSG); } ahc->needsdtr &= ~targ_mask; break; } case MSG_EXT_WDTR: { u_int8_t scratch, bus_width; if (message_length != MSG_EXT_WDTR_LEN) { ahc_outb(ahc, RETURN_1, SEND_REJ); break; } bus_width = ahc_inb(ahc, MSGIN_EXT_BYTES); scratch = ahc_inb(ahc, TARG_SCRATCH + scratch_offset); if ((scb->flags & SCB_MSGOUT_WDTR) != 0) { /* * Don't send a WDTR back to the * target, since we asked first. */ ahc_outb(ahc, RETURN_1, 0); switch (bus_width){ case BUS_8_BIT: scratch &= 0x7f; break; case BUS_16_BIT: if (bootverbose) printf("%s: target %d using " "16Bit transfers\n", ahc_name(ahc), target); scratch |= WIDEXFER; break; case BUS_32_BIT: /* * How can we do 32bit transfers * on a 16bit bus? */ ahc_outb(ahc, RETURN_1, SEND_REJ); printf("%s: target %d requested 32Bit " "transfers. Rejecting...\n", ahc_name(ahc), target); break; default: break; } } else { /* * Send our own WDTR in reply */ switch (bus_width) { case BUS_8_BIT: scratch &= 0x7f; break; case BUS_32_BIT: case BUS_16_BIT: if (ahc->type & AHC_WIDE) { /* Negotiate 16_BITS */ bus_width = BUS_16_BIT; if (bootverbose) printf("%s: target %d " "using 16Bit " "transfers\n", ahc_name(ahc), target); scratch |= WIDEXFER; } else bus_width = BUS_8_BIT; break; default: break; } ahc_construct_wdtr(ahc, /*start_byte*/0, bus_width); ahc_outb(ahc, RETURN_1, SEND_MSG); } ahc->needwdtr &= ~targ_mask; ahc_outb(ahc, TARG_SCRATCH + scratch_offset, scratch); ahc_outb(ahc, SCSIRATE, scratch); break; } default: /* Unknown extended message. Reject it. */ ahc_outb(ahc, RETURN_1, SEND_REJ); } break; } case REJECT_MSG: { /* * What we care about here is if we had an * outstanding SDTR or WDTR message for this * target. If we did, this is a signal that * the target is refusing negotiation. */ u_int8_t targ_scratch; u_int8_t scb_index; scb_index = ahc_inb(ahc, SCB_TAG); scb = ahc->scb_data->scbarray[scb_index]; targ_scratch = ahc_inb(ahc, TARG_SCRATCH + scratch_offset); if ((scb->flags & SCB_MSGOUT_WDTR) != 0) { /* note 8bit xfers and clear flag */ targ_scratch &= 0x7f; ahc->needwdtr &= ~targ_mask; printf("%s:%c:%d: refuses WIDE negotiation. Using " "8bit transfers\n", ahc_name(ahc), channel, target); } else if ((scb->flags & SCB_MSGOUT_SDTR) != 0) { /* note asynch xfers and clear flag */ targ_scratch &= 0xf0; ahc->needsdtr &= ~targ_mask; printf("%s:%c:%d: refuses synchronous negotiation. " "Using asynchronous transfers\n", ahc_name(ahc), channel, target); } else { /* * Otherwise, we ignore it. */ #ifdef AHC_DEBUG if (ahc_debug & AHC_SHOWMISC) printf("%s:%c:%d: Message reject -- ignored\n", ahc_name(ahc), channel, target); #endif break; } ahc_outb(ahc, TARG_SCRATCH + scratch_offset, targ_scratch); ahc_outb(ahc, SCSIRATE, targ_scratch); break; } case BAD_STATUS: { u_int8_t scb_index; struct scsi_xfer *xs; struct hardware_scb *hscb; /* * The sequencer will notify us when a command * has an error that would be of interest to * the kernel. This allows us to leave the sequencer * running in the common case of command completes * without error. The sequencer will already have * dma'd the SCB back up to us, so we can reference * the in kernel copy directly. */ scb_index = ahc_inb(ahc, SCB_TAG); scb = ahc->scb_data->scbarray[scb_index]; hscb = scb->hscb; /* * Set the default return value to 0 (don't * send sense). The sense code will change * this if needed and this reduces code * duplication. */ ahc_outb(ahc, RETURN_1, 0); if (!(scb && (scb->flags & SCB_ACTIVE))) { printf("%s:%c:%d: ahc_intr - referenced scb " "not valid during seqint 0x%x scb(%d)\n", ahc_name(ahc), channel, target, intstat, scb_index); goto clear; } xs = scb->xs; xs->status = hscb->status; switch (hscb->status){ case SCSI_OK: printf("%s: Interrupted for staus of" " 0???\n", ahc_name(ahc)); break; case SCSI_CHECK: #ifdef AHC_DEBUG if (ahc_debug & AHC_SHOWSENSE) { sc_print_addr(xs->sc_link); printf("SCB %d: requests Check Status\n", scb->hscb->tag); } #endif if ((xs->error == XS_NOERROR) && !(scb->flags & SCB_SENSE)) { struct ahc_dma_seg *sg = scb->ahc_dma; struct scsi_sense *sc = &(scb->sense_cmd); /* * Save off the residual if there is one. */ if (hscb->residual_SG_segment_count != 0) ahc_calc_residual(scb); #ifdef AHC_DEBUG if (ahc_debug & AHC_SHOWSENSE) { sc_print_addr(xs->sc_link); printf("Sending Sense\n"); } #endif #if defined(__FreeBSD__) sc->op_code = REQUEST_SENSE; #elif defined(__NetBSD__) sc->opcode = REQUEST_SENSE; #endif sc->byte2 = xs->sc_link->lun << 5; sc->length = sizeof(struct scsi_sense_data); sc->control = 0; sg->addr = vtophys(&xs->sense); sg->len = sizeof(struct scsi_sense_data); hscb->control &= DISCENB; hscb->status = 0; hscb->SG_segment_count = 1; hscb->SG_list_pointer = vtophys(sg); hscb->data = sg->addr; /* Maintain SCB_LINKED_NEXT */ hscb->datalen &= 0xFF000000; hscb->datalen |= sg->len; hscb->cmdpointer = vtophys(sc); hscb->cmdlen = sizeof(*sc); scb->sg_count = hscb->SG_segment_count; scb->flags |= SCB_SENSE; /* * Ensure the target is busy since this * will be an untagged request. */ ahc_busy_target(ahc, target, channel, hscb->tag); ahc_outb(ahc, RETURN_1, SEND_SENSE); /* * Ensure we have enough time to actually * retrieve the sense. */ untimeout(ahc_timeout, (caddr_t)scb); timeout(ahc_timeout, (caddr_t)scb, hz); break; } /* * Clear the SCB_SENSE Flag and have * the sequencer do a normal command * complete with either a "DRIVER_STUFFUP" * error or whatever other error condition * we already had. */ scb->flags &= ~SCB_SENSE; if (xs->error == XS_NOERROR) xs->error = XS_DRIVER_STUFFUP; break; case SCSI_QUEUE_FULL: if (scb->hscb->control & TAG_ENB) { /* * The upper level SCSI code in 3.0 * handles this properly... */ struct scsi_link *sc_link; sc_link = xs->sc_link; if (sc_link->active > 2 && sc_link->opennings != 0) { /* truncate the opennings */ sc_link->opennings = 0; sc_print_addr(sc_link); printf("Tagged openings reduced to " "%d\n", sc_link->active); } /* * XXX requeue this unconditionally. */ scb->xs->retries++; scb->xs->error = XS_BUSY; break; } /* Else treat as if it is a BUSY condition */ scb->hscb->status = SCSI_BUSY; /* Fall Through... */ case SCSI_BUSY: xs->error = XS_BUSY; sc_print_addr(xs->sc_link); printf("Target Busy\n"); break; default: sc_print_addr(xs->sc_link); printf("unexpected targ_status: %x\n", hscb->status); xs->error = XS_DRIVER_STUFFUP; break; } break; } case AWAITING_MSG: { int scb_index; u_int8_t message_offset; scb_index = ahc_inb(ahc, SCB_TAG); scb = ahc->scb_data->scbarray[scb_index]; /* * This SCB had MK_MESSAGE set in its control byte, * informing the sequencer that we wanted to send a * special message to this target. */ message_offset = ahc_inb(ahc, MSG_LEN); if (scb->flags & SCB_DEVICE_RESET) { ahc_outb(ahc, MSG_OUT, MSG_BUS_DEV_RESET); ahc_outb(ahc, MSG_LEN, 1); sc_print_addr(scb->xs->sc_link); printf("Bus Device Reset Message Sent\n"); } else if (scb->flags & SCB_ABORT) { if ((scb->hscb->control & TAG_ENB) != 0) ahc_outb(ahc, MSG_OUT + message_offset, MSG_ABORT_TAG); else ahc_outb(ahc, MSG_OUT + message_offset, MSG_ABORT); ahc_outb(ahc, MSG_LEN, message_offset + 1); sc_print_addr(scb->xs->sc_link); printf("Abort Message Sent\n"); } else if (scb->flags & SCB_MSGOUT_WDTR) { ahc_construct_wdtr(ahc, message_offset, BUS_16_BIT); } else if (scb->flags & SCB_MSGOUT_SDTR) { int sxfr; int i; u_int16_t ultraenable; u_int8_t target_scratch; /* Pull the user defined setting */ target_scratch = ahc_inb(ahc, TARG_SCRATCH + scratch_offset); sxfr = target_scratch & SXFR; ultraenable = ahc_inb(ahc, ULTRA_ENB) | (ahc_inb(ahc, ULTRA_ENB + 1) << 8); if (ultraenable & targ_mask) /* Want an ultra speed in the table */ sxfr |= 0x100; for (i = 0; i < ahc_num_syncrates; i++) if (sxfr == ahc_syncrates[i].sxfr) break; ahc_construct_sdtr(ahc, message_offset, ahc_syncrates[i].period, (target_scratch & WIDEXFER) ? MAX_OFFSET_16BIT : MAX_OFFSET_8BIT); } else panic("ahc_intr: AWAITING_MSG for an SCB that " "does not have a waiting message"); break; } case DATA_OVERRUN: { /* * When the sequencer detects an overrun, it * sets STCNT to 0x00ffffff and allows the * target to complete its transfer in * BITBUCKET mode. */ u_int8_t scbindex = ahc_inb(ahc, SCB_TAG); u_int8_t lastphase = ahc_inb(ahc, LASTPHASE); u_int32_t overrun; int i; scb = ahc->scb_data->scbarray[scbindex]; overrun = ahc_inb(ahc, STCNT) | (ahc_inb(ahc, STCNT + 1) << 8) | (ahc_inb(ahc, STCNT + 2) << 16); overrun = 0x00ffffff - overrun; sc_print_addr(scb->xs->sc_link); printf("data overrun of %d bytes detected in %s phase." " Tag == 0x%x. Forcing a retry.\n", overrun, lastphase == P_DATAIN ? "Data-In" : "Data-Out", scb->hscb->tag); sc_print_addr(scb->xs->sc_link); printf("%s seen Data Phase. Length = %d. NumSGs = %d.\n", ahc_inb(ahc, SEQ_FLAGS) & DPHASE ? "Have" : "Haven't", scb->xs->datalen, scb->sg_count); for (i = 0; i < scb->sg_count; i++) { printf("sg[%d] - Addr 0x%x : Length %d\n", i, scb->ahc_dma[i].addr, scb->ahc_dma[i].len); } /* * Set this and it will take affect when the * target does a command complete. */ scb->xs->error = XS_DRIVER_STUFFUP; break; } #if NOT_YET /* XXX Fill these in later */ case MESG_BUFFER_BUSY: break; case MSGIN_PHASEMIS: break; #endif #if 0 case SCB_TRACE_POINT: { /* * Print out the bus phase */ char *phase; u_int8_t scbindex = ahc_inb(ahc, SCB_TAG); u_int8_t lastphase = ahc_inb(ahc, LASTPHASE); scb = ahc->scb_data->scbarray[scbindex]; sc_print_addr(scb->xs->sc_link); switch (lastphase) { case P_DATAOUT: phase = "Data-Out"; break; case P_DATAIN: phase = "Data-In"; break; case P_COMMAND: phase = "Command"; break; case P_MESGOUT: phase = "Message-Out"; break; case P_STATUS: phase = "Status"; break; case P_MESGIN: phase = "Message-In"; break; default: phase = "busfree"; break; } printf("- %s\n", phase); break; } #endif case ABORT_CMDCMPLT: /* This interrupt serves to pause the sequencer * until we can clean up the QOUTFIFO allowing us * to hanle any abort SCBs that may have completed * yet still have an SCB in the QINFIFO or * waiting for selection queue. By the time we get * here, we should have already cleaned up the * queues, so all we need to do is unpause the sequencer. */ break; default: printf("ahc_intr: seqint, " "intstat == 0x%x, scsisigi = 0x%x\n", intstat, ahc_inb(ahc, SCSISIGI)); break; } clear: /* * Clear the upper byte that holds SEQINT status * codes and clear the SEQINT bit. */ ahc_outb(ahc, CLRINT, CLRSEQINT); /* * The sequencer is paused immediately on * a SEQINT, so we should restart it when * we're done. */ unpause_sequencer(ahc, /*unpause_always*/TRUE); } static void ahc_handle_scsiint(ahc, intstat) struct ahc_softc *ahc; u_int8_t intstat; { u_int8_t scb_index; u_int8_t status; struct scb *scb; scb_index = ahc_inb(ahc, SCB_TAG); status = ahc_inb(ahc, SSTAT1); if (scb_index < ahc->scb_data->numscbs) { scb = ahc->scb_data->scbarray[scb_index]; if ((scb->flags & SCB_ACTIVE) == 0) scb = NULL; } else scb = NULL; if ((status & SCSIRSTI) != 0) { char channel; channel = (ahc_inb(ahc, SBLKCTL) & SELBUSB) ? 'B' : 'A'; printf("%s: Someone reset channel %c\n", ahc_name(ahc), channel); ahc_reset_channel(ahc, channel, XS_BUSY, /* Initiate Reset */FALSE); scb = NULL; } else if ((status & BUSFREE) != 0 && (status & SELTO) == 0) { /* * First look at what phase we were last in. * If its message out, chances are pretty good * that the busfree was in response to one of * our abort requests. */ u_int8_t lastphase = ahc_inb(ahc, LASTPHASE); u_int8_t target = (ahc_inb(ahc, SAVED_TCL) >> 4) & 0x0f; char channel = ahc_inb(ahc, SBLKCTL) & SELBUSB ? 'B': 'A'; int printerror = 1; ahc_outb(ahc, SCSISEQ, 0); if (lastphase == P_MESGOUT) { u_int8_t sindex; u_int8_t message; sindex = ahc_inb(ahc, SINDEX); message = ahc_inb(ahc, sindex - 1); if (message == MSG_ABORT) { sc_print_addr(scb->xs->sc_link); printf("SCB %d - Abort Completed.\n", scb->hscb->tag); ahc_reset_device(ahc, target, channel, SCB_LUN(scb), SCB_LIST_NULL, XS_TIMEOUT); ahc_run_done_queue(ahc); scb = NULL; printerror = 0; } else if (message == MSG_ABORT_TAG) { sc_print_addr(scb->xs->sc_link); printf("SCB %d - Abort Tag Completed.\n", scb->hscb->tag); ahc_reset_device(ahc, target, channel, SCB_LUN(scb), scb->hscb->tag, XS_TIMEOUT); ahc_run_done_queue(ahc); scb = NULL; printerror = 0; } else if (message == MSG_BUS_DEV_RESET) { ahc_handle_devreset(ahc, target, channel); scb = NULL; printerror = 0; } } if (printerror != 0) { if (scb != NULL) { u_int8_t tag; if ((scb->hscb->control & TAG_ENB) != 0) tag = scb->hscb->tag; else tag = SCB_LIST_NULL; ahc_reset_device(ahc, target, channel, SCB_LUN(scb), tag, XS_TIMEOUT); } else { /* * XXX can we handle this better? * Reset the bus? Send a Bus Device Reset? */ ahc_reset_device(ahc, target, channel, ALL_LUNS, SCB_LIST_NULL, XS_TIMEOUT); printf("%s: ", ahc_name(ahc)); } printf("Unexpected busfree. LASTPHASE == 0x%x\n" "SEQADDR == 0x%x\n", lastphase, (ahc_inb(ahc, SEQADDR1) << 8) | ahc_inb(ahc, SEQADDR0)); } ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); ahc_outb(ahc, CLRSINT1, CLRBUSFREE); ahc_outb(ahc, CLRINT, CLRSCSIINT); restart_sequencer(ahc); } else if ((status & SELTO) != 0) { struct scsi_xfer *xs; u_int8_t scbptr; u_int8_t nextscb; scbptr = ahc_inb(ahc, WAITING_SCBH); ahc_outb(ahc, SCBPTR, scbptr); scb_index = ahc_inb(ahc, SCB_TAG); if (scb_index < ahc->scb_data->numscbs) { scb = ahc->scb_data->scbarray[scb_index]; if ((scb->flags & SCB_ACTIVE) == 0) scb = NULL; } else scb = NULL; if (scb == NULL) { printf("%s: ahc_intr - referenced scb not " "valid during SELTO scb(%d)\n", ahc_name(ahc), scb_index); printf("SEQADDR = 0x%x SCSISEQ = 0x%x " "SSTAT0 = 0x%x SSTAT1 = 0x%x\n", ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8), ahc_inb(ahc, SCSISEQ), ahc_inb(ahc, SSTAT0), ahc_inb(ahc,SSTAT1)); } else { /* * XXX If we queued an abort tag, go clean up the * disconnected list. */ xs = scb->xs; xs->error = XS_SELTIMEOUT; /* * Clear any pending messages for the timed out * target, and mark the target as free */ ahc_outb(ahc, MSG_LEN, 0); ahc_index_busy_target(ahc, SCB_TARGET(scb), SCB_IS_SCSIBUS_B(scb) ? 'B' : 'A', /*unbusy*/TRUE); ahc_outb(ahc, SCB_CONTROL, 0); /* Shift the waiting Q forward. */ nextscb = ahc_inb(ahc, SCB_NEXT); ahc_outb(ahc, WAITING_SCBH, nextscb); ahc_add_curscb_to_free_list(ahc); } /* Stop the selection */ ahc_outb(ahc, SCSISEQ, 0); ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRBUSFREE); ahc_outb(ahc, CLRINT, CLRSCSIINT); restart_sequencer(ahc); } else if (scb == NULL) { printf("%s: ahc_intr - referenced scb not " "valid during scsiint 0x%x scb(%d)\n" "SIMODE0 = 0x%x, SIMODE1 = 0x%x, SSTAT0 = 0x%x\n" "SEQADDR = 0x%x\n", ahc_name(ahc), status, scb_index, ahc_inb(ahc, SIMODE0), ahc_inb(ahc, SIMODE1), ahc_inb(ahc, SSTAT0), (ahc_inb(ahc, SEQADDR1) << 8) | ahc_inb(ahc, SEQADDR0)); ahc_outb(ahc, CLRSINT1, status); ahc_outb(ahc, CLRINT, CLRSCSIINT); unpause_sequencer(ahc, /*unpause_always*/TRUE); scb = NULL; } else if ((status & SCSIPERR) != 0) { /* * Determine the bus phase and * queue an appropriate message */ char *phase; u_int8_t mesg_out = MSG_NOOP; u_int8_t lastphase = ahc_inb(ahc, LASTPHASE); struct scsi_xfer *xs; xs = scb->xs; sc_print_addr(xs->sc_link); switch (lastphase) { case P_DATAOUT: phase = "Data-Out"; break; case P_DATAIN: phase = "Data-In"; mesg_out = MSG_INITIATOR_DET_ERR; break; case P_COMMAND: phase = "Command"; break; case P_MESGOUT: phase = "Message-Out"; break; case P_STATUS: phase = "Status"; mesg_out = MSG_INITIATOR_DET_ERR; break; case P_MESGIN: phase = "Message-In"; mesg_out = MSG_PARITY_ERROR; break; default: phase = "unknown"; break; } printf("parity error during %s phase.\n", phase); /* * We've set the hardware to assert ATN if we * get a parity error on "in" phases, so all we * need to do is stuff the message buffer with * the appropriate message. "In" phases have set * mesg_out to something other than MSG_NOP. */ if (mesg_out != MSG_NOOP) { ahc_outb(ahc, MSG_OUT, mesg_out); ahc_outb(ahc, MSG_LEN, 1); scb = NULL; } else /* * Should we allow the target to make * this decision for us? If we get a * sense request from the drive, we will * not fetch it since xs->error != XS_NOERROR. * perhaps we need two error fields in the * xs structure? */ xs->error = XS_DRIVER_STUFFUP; ahc_outb(ahc, CLRSINT1, CLRSCSIPERR); ahc_outb(ahc, CLRINT, CLRSCSIINT); unpause_sequencer(ahc, /*unpause_always*/TRUE); } else { sc_print_addr(scb->xs->sc_link); printf("Unknown SCSIINT. Status = 0x%x\n", status); ahc_outb(ahc, CLRSINT1, status); ahc_outb(ahc, CLRINT, CLRSCSIINT); unpause_sequencer(ahc, /*unpause_always*/TRUE); scb = NULL; } if (scb != NULL) { /* We want to process the command */ ahc_done(ahc, scb); } } static void ahc_handle_devreset(ahc, target, channel) struct ahc_softc *ahc; int target; char channel; { u_int16_t targ_mask; u_int8_t targ_scratch; int scratch_offset = target; int found; if (channel == 'B') scratch_offset += 8; targ_mask = (0x01 << scratch_offset); /* * Go back to async/narrow transfers and * renegotiate. */ ahc->needsdtr |= ahc->needsdtr_orig & targ_mask; ahc->needwdtr |= ahc->needwdtr_orig & targ_mask; ahc->sdtrpending &= ~targ_mask; ahc->wdtrpending &= ~targ_mask; targ_scratch = ahc_inb(ahc, TARG_SCRATCH + scratch_offset); targ_scratch &= SXFR; ahc_outb(ahc, TARG_SCRATCH + scratch_offset, targ_scratch); found = ahc_reset_device(ahc, target, channel, ALL_LUNS, SCB_LIST_NULL, XS_NOERROR); printf("%s: Bus Device Reset delivered. %d SCBs aborted\n", ahc_name(ahc), found); ahc_run_done_queue(ahc); } /* * We have a scb which has been processed by the * adaptor, now we look to see how the operation * went. */ static void ahc_done(ahc, scb) struct ahc_softc *ahc; struct scb *scb; { struct scsi_xfer *xs = scb->xs; SC_DEBUG(xs->sc_link, SDEV_DB2, ("ahc_done\n")); /* * If the recovery SCB completes, we have to be * out of our timeout. */ if (scb->flags & SCB_RECOVERY_SCB) { ahc->in_timeout = FALSE; sc_print_addr(scb->xs->sc_link); printf("no longer in timeout\n"); } /* * Put the results of the operation * into the xfer and call whoever started it */ /* Don't override the error value. */ if (xs->error == XS_NOERROR && (scb->flags & SCB_SENSE) != 0) xs->error = XS_SENSE; #if defined(__FreeBSD__) if ((xs->flags & SCSI_ERR_OK) && !(xs->error == XS_SENSE)) { /* All went correctly OR errors expected */ xs->error = XS_NOERROR; } #elif defined(__NetBSD__) /* * Since NetBSD doesn't have error ignoring operation mode * (SCSI_ERR_OK in FreeBSD), we don't have to care this case. */ #endif xs->flags |= ITSDONE; #ifdef AHC_TAGENABLE /* * This functionality will be provided by the generic SCSI layer * in FreeBSD 3.0. */ if (xs->cmd->opcode == INQUIRY && xs->error == XS_NOERROR) { struct scsi_inquiry_data *inq_data; u_int16_t mask = 0x01 << (xs->sc_link->target | (scb->hscb->tcl & 0x08)); /* * Sneak a look at the results of the SCSI Inquiry * command and see if we can do Tagged queing. This * should really be done by the higher level drivers. */ inq_data = (struct scsi_inquiry_data *)xs->data; if ((inq_data->flags & SID_CmdQue) && !(ahc->tagenable & mask)) { printf("%s: target %d Tagged Queuing Device\n", ahc_name(ahc), xs->sc_link->target); ahc->tagenable |= mask; if (ahc->scb_data->maxhscbs >= 16 || (ahc->flags & AHC_PAGESCBS)) { /* Default to 8 tags */ xs->sc_link->opennings += 6; } else { /* * Default to 4 tags on whimpy * cards that don't have much SCB * space and can't page. This prevents * a single device from hogging all * slots. We should really have a better * way of providing fairness. */ xs->sc_link->opennings += 2; } } } #endif /* AHC_TAGENABLE */ if ((scb->flags & SCB_MSGOUT_WDTR|SCB_MSGOUT_SDTR) != 0) { /* * Turn off the pending flags for any DTR messages * regardless of whether they completed successfully * or not. This ensures that we don't have lingering * state after we abort an SCB. */ u_int16_t mask; mask = (0x01 << (xs->sc_link->target | (IS_SCSIBUS_B(ahc, xs->sc_link) ? SELBUSB : 0))); if (scb->flags & SCB_MSGOUT_WDTR) ahc->wdtrpending &= ~mask; if (scb->flags & SCB_MSGOUT_SDTR) ahc->sdtrpending &= ~mask; } untimeout(ahc_timeout, (caddr_t)scb); ahc_free_scb(ahc, scb); /* * If we're polling, we rely on the ITS_DONE flag in the xs structure * to know that the command has completed. Unfortunately, scsi_done * can cause the same xs to get requeued putting us in an infinite * loop. So, we defer the scsi_done call until the poll routine exits * its loop. I hate the way this works. */ if ((xs->flags & SCSI_NOMASK) == 0) scsi_done(xs); } /* * Start the board, ready for normal operation */ int ahc_init(ahc) struct ahc_softc *ahc; { u_int8_t scsi_conf, sblkctl, sxfrctl1, i; u_int16_t ultraenable = 0; int max_targ = 15; /* * Assume we have a board at this stage and it has been reset. */ /* Handle the SCBPAGING option */ #ifndef AHC_SCBPAGING_ENABLE ahc->flags &= ~AHC_PAGESCBS; #endif /* Determine channel configuration and who we are on the scsi bus. */ switch ((sblkctl = ahc_inb(ahc, SBLKCTL) & 0x0a)) { case 0: ahc->our_id = (ahc_inb(ahc, SCSICONF) & HSCSIID); ahc->flags &= ~AHC_CHANNEL_B_PRIMARY; if ((ahc->type & AHC_39X) != 0) { char channel = 'A'; if ((ahc->flags & (AHC_CHNLB|AHC_CHNLC)) != 0) channel = ahc->flags & AHC_CHNLB ? 'B' : 'C'; printf("Channel %c, SCSI Id=%d, ", channel, ahc->our_id); } else printf("Single Channel, SCSI Id=%d, ", ahc->our_id); ahc_outb(ahc, SEQ_FLAGS, ahc->flags & AHC_PAGESCBS); break; case 2: ahc->our_id = (ahc_inb(ahc, SCSICONF + 1) & HWSCSIID); ahc->flags &= ~AHC_CHANNEL_B_PRIMARY; if ((ahc->type & AHC_39X) != 0) { char channel = 'A'; if ((ahc->flags & (AHC_CHNLB|AHC_CHNLC)) != 0) channel = ahc->flags & AHC_CHNLB ? 'B' : 'C'; printf("Wide Channel %c, SCSI Id=%d, ", channel, ahc->our_id); } else printf("Wide Channel, SCSI Id=%d, ", ahc->our_id); ahc->type |= AHC_WIDE; ahc_outb(ahc, SEQ_FLAGS, WIDE_BUS | (ahc->flags & AHC_PAGESCBS)); break; case 8: ahc->our_id = (ahc_inb(ahc, SCSICONF) & HSCSIID); ahc->our_id_b = (ahc_inb(ahc, SCSICONF + 1) & HSCSIID); printf("Twin Channel, A SCSI Id=%d, B SCSI Id=%d, ", ahc->our_id, ahc->our_id_b); ahc->type |= AHC_TWIN; ahc_outb(ahc, SEQ_FLAGS, TWIN_BUS | (ahc->flags & AHC_PAGESCBS)); break; default: printf(" Unsupported adapter type. Ignoring\n"); return(-1); } /* Determine the number of SCBs and initialize them */ if (ahc->scb_data->maxhscbs == 0) { /* SCB 0 heads the free list */ ahc_outb(ahc, FREE_SCBH, 0); for (i = 0; i < AHC_SCB_MAX; i++) { ahc_outb(ahc, SCBPTR, i); ahc_outb(ahc, SCB_CONTROL, i); if(ahc_inb(ahc, SCB_CONTROL) != i) break; ahc_outb(ahc, SCBPTR, 0); if(ahc_inb(ahc, SCB_CONTROL) != 0) break; ahc_outb(ahc, SCBPTR, i); /* Clear the control byte. */ ahc_outb(ahc, SCB_CONTROL, 0); /* Set the next pointer */ ahc_outb(ahc, SCB_NEXT, i+1); /* Make the tag number invalid */ ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); /* No Busy non-tagged targets yet */ ahc_outb(ahc, SCB_BUSYTARGETS, SCB_LIST_NULL); ahc_outb(ahc, SCB_BUSYTARGETS + 1, SCB_LIST_NULL); ahc_outb(ahc, SCB_BUSYTARGETS + 2, SCB_LIST_NULL); ahc_outb(ahc, SCB_BUSYTARGETS + 3, SCB_LIST_NULL); } /* Make that the last SCB terminates the free list */ ahc_outb(ahc, SCBPTR, i-1); ahc_outb(ahc, SCB_NEXT, SCB_LIST_NULL); /* Ensure we clear the 0 SCB's control byte. */ ahc_outb(ahc, SCBPTR, 0); ahc_outb(ahc, SCB_CONTROL, 0); ahc->scb_data->maxhscbs = i; } if ((ahc->scb_data->maxhscbs < AHC_SCB_MAX) && (ahc->flags & AHC_PAGESCBS)) { u_int8_t max_scbid = 255; /* Determine the number of valid bits in the FIFOs */ ahc_outb(ahc, QINFIFO, max_scbid); max_scbid = ahc_inb(ahc, QINFIFO); ahc->scb_data->maxscbs = MIN(AHC_SCB_MAX, max_scbid + 1); printf("%d/%d SCBs\n", ahc->scb_data->maxhscbs, ahc->scb_data->maxscbs); } else { ahc->scb_data->maxscbs = ahc->scb_data->maxhscbs; ahc->flags &= ~AHC_PAGESCBS; printf("%d SCBs\n", ahc->scb_data->maxhscbs); } #ifdef AHC_DEBUG if (ahc_debug & AHC_SHOWMISC) { printf("%s: hardware scb %d bytes; kernel scb %d bytes; " "ahc_dma %d bytes\n", ahc_name(ahc), sizeof(struct hardware_scb), sizeof(struct scb), sizeof(struct ahc_dma_seg)); } #endif /* AHC_DEBUG */ /* Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1, for both channels*/ if (ahc->type & AHC_TWIN) { /* * The device is gated to channel B after a chip reset, * so set those values first */ ahc_outb(ahc, SCSIID, ahc->our_id_b); scsi_conf = ahc_inb(ahc, SCSICONF + 1); sxfrctl1 = ahc_inb(ahc, SXFRCTL1); ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) |(sxfrctl1 & STPWEN) |ENSTIMER|ACTNEGEN); ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); if (ahc->type & AHC_ULTRA) ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN|FAST20); else ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); if (scsi_conf & RESET_SCSI) { /* Reset the bus */ if (bootverbose) printf("%s: Resetting Channel B\n", ahc_name(ahc)); ahc_reset_current_bus(ahc); } /* Select Channel A */ ahc_outb(ahc, SBLKCTL, 0); } ahc_outb(ahc, SCSIID, ahc->our_id); scsi_conf = ahc_inb(ahc, SCSICONF); sxfrctl1 = ahc_inb(ahc, SXFRCTL1); ahc_outb(ahc, SXFRCTL1, (scsi_conf & (ENSPCHK|STIMESEL)) |(sxfrctl1 & STPWEN) |ENSTIMER|ACTNEGEN); ahc_outb(ahc, SIMODE1, ENSELTIMO|ENSCSIRST|ENSCSIPERR); if (ahc->type & AHC_ULTRA) ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN|FAST20); else ahc_outb(ahc, SXFRCTL0, DFON|SPIOEN); if (scsi_conf & RESET_SCSI) { /* Reset the bus */ if (bootverbose) printf("%s: Resetting Channel A\n", ahc_name(ahc)); ahc_reset_current_bus(ahc); } /* * Look at the information that board initialization or * the board bios has left us. In the lower four bits of each * target's scratch space any value other than 0 indicates * that we should initiate synchronous transfers. If it's zero, * the user or the BIOS has decided to disable synchronous * negotiation to that target so we don't activate the needsdtr * flag. */ ahc->needsdtr_orig = 0; ahc->needwdtr_orig = 0; /* Grab the disconnection disable table and invert it for our needs */ if (ahc->flags & AHC_USEDEFAULTS) { printf("%s: Host Adapter Bios disabled. Using default SCSI " "device parameters\n", ahc_name(ahc)); ahc->discenable = 0xff; } else ahc->discenable = ~((ahc_inb(ahc, DISC_DSB + 1) << 8) | ahc_inb(ahc, DISC_DSB)); if (!(ahc->type & (AHC_WIDE|AHC_TWIN))) max_targ = 7; for (i = 0; i <= max_targ; i++) { u_int8_t target_settings; if (ahc->flags & AHC_USEDEFAULTS) { target_settings = 0; /* 10MHz/20MHz */ ahc->needsdtr_orig |= (0x01 << i); ahc->needwdtr_orig |= (0x01 << i); if (ahc->type & AHC_ULTRA) ultraenable |= (0x01 << i); } else { /* Take the settings leftover in scratch RAM. */ target_settings = ahc_inb(ahc, TARG_SCRATCH + i); if (target_settings & 0x0f) { ahc->needsdtr_orig |= (0x01 << i); /*Default to a asynchronous transfers(0 offset)*/ target_settings &= 0xf0; } if (target_settings & 0x80) { ahc->needwdtr_orig |= (0x01 << i); /* * We'll set the Wide flag when we * are successful with Wide negotiation. * Turn it off for now so we aren't * confused. */ target_settings &= 0x7f; } if (ahc->type & AHC_ULTRA) { /* * Enable Ultra for any target that * has a valid ultra syncrate setting. */ u_int8_t rate = target_settings & 0x70; if (rate == 0x00 || rate == 0x10 || rate == 0x20 || rate == 0x40) { if (rate == 0x40) { /* Treat 10MHz specially */ target_settings &= ~0x70; } else ultraenable |= (0x01 << i); } } } ahc_outb(ahc, TARG_SCRATCH+i,target_settings); } /* * If we are not a WIDE device, forget WDTR. This * makes the driver work on some cards that don't * leave these fields cleared when the BIOS is not * installed. */ if ((ahc->type & AHC_WIDE) == 0) ahc->needwdtr_orig = 0; ahc->needsdtr = ahc->needsdtr_orig; ahc->needwdtr = ahc->needwdtr_orig; ahc->sdtrpending = 0; ahc->wdtrpending = 0; ahc->tagenable = 0; ahc->orderedtag = 0; ahc_outb(ahc, ULTRA_ENB, ultraenable & 0xff); ahc_outb(ahc, ULTRA_ENB + 1, (ultraenable >> 8) & 0xff); #ifdef AHC_DEBUG /* How did we do? */ if (ahc_debug & AHC_SHOWMISC) printf("NEEDSDTR == 0x%x\nNEEDWDTR == 0x%x\n" "DISCENABLE == 0x%x\n", ahc->needsdtr, ahc->needwdtr, ahc->discenable); #endif /* * Set the number of available hardware SCBs */ ahc_outb(ahc, SCBCOUNT, ahc->scb_data->maxhscbs); /* * 2's compliment of maximum tag value */ i = ahc->scb_data->maxscbs; ahc_outb(ahc, COMP_SCBCOUNT, -i & 0xff); /* * Allocate enough "hardware scbs" to handle * the maximum number of concurrent transactions * we can have active. We have to use contigmalloc * if this array crosses a page boundary since the * sequencer depends on this array being physically * contiguous. */ if (ahc->scb_data->hscbs == NULL) { size_t array_size; u_int32_t hscb_physaddr; array_size = ahc->scb_data->maxscbs*sizeof(struct hardware_scb); if (array_size > PAGE_SIZE) { ahc->scb_data->hscbs = (struct hardware_scb *) contigmalloc(array_size, M_DEVBUF, M_NOWAIT, 0ul, 0xffffffff, PAGE_SIZE, 0x10000); } else { ahc->scb_data->hscbs = (struct hardware_scb *) malloc(array_size, M_DEVBUF, M_NOWAIT); } if (ahc->scb_data->hscbs == NULL) { printf("%s: unable to allocate hardware SCB array. " "Failing attach\n"); return (-1); } /* At least the control byte of each hscb needs to be zeroed */ bzero(ahc->scb_data->hscbs, array_size); /* Tell the sequencer where it can find the hscb array. */ hscb_physaddr = vtophys(ahc->scb_data->hscbs); ahc_outb(ahc, HSCB_ADDR, hscb_physaddr & 0xFF); ahc_outb(ahc, HSCB_ADDR + 1, (hscb_physaddr >> 8)& 0xFF); ahc_outb(ahc, HSCB_ADDR + 2, (hscb_physaddr >> 16)& 0xFF); ahc_outb(ahc, HSCB_ADDR + 3, (hscb_physaddr >> 24)& 0xFF); } /* * Q-Full-Count. Some cards have more Q space * then SCBs. */ if (ahc->type & AHC_AIC7770) { ahc->qfullcount = 4; ahc->qcntmask = 0x07; } else if (ahc->type & AHC_AIC7850) { ahc->qfullcount = 8; ahc->qcntmask = 0x0f; } else if (ahc->scb_data->maxhscbs == 255) { /* 7870/7880 with external SRAM */ ahc->qfullcount = 255; ahc->qcntmask = 0xff; } else { /* 7870/7880 */ ahc->qfullcount = 16; ahc->qcntmask = 0x1f; } /* * QCount mask to deal with broken aic7850s that * sporadically get garbage in the upper bits of * their QCount registers. */ ahc_outb(ahc, QCNTMASK, ahc->qcntmask); /* We don't have any waiting selections */ ahc_outb(ahc, WAITING_SCBH, SCB_LIST_NULL); /* Our disconnection list is empty too */ ahc_outb(ahc, DISCONNECTED_SCBH, SCB_LIST_NULL); /* Message out buffer starts empty */ ahc_outb(ahc, MSG_LEN, 0x00); /* * Load the Sequencer program and Enable the adapter * in "fast" mode. */ if (bootverbose) printf("%s: Downloading Sequencer Program...", ahc_name(ahc)); ahc_loadseq(ahc); if (bootverbose) printf("Done\n"); unpause_sequencer(ahc, /*unpause_always*/TRUE); /* Notify us when the system can handle timeouts */ timeout(ahc_first_timeout, NULL, 0); /* * Note that we are going and return (to probe) */ ahc->flags |= AHC_INIT; return (0); } static void ahcminphys(bp) struct buf *bp; { /* * Even though the card can transfer up to 16megs per command * we are limited by the number of segments in the dma segment * list that we can hold. The worst case is that all pages are * discontinuous physically, hense the "page per segment" limit * enforced here. */ if (bp->b_bcount > ((AHC_NSEG - 1) * PAGE_SIZE)) { bp->b_bcount = ((AHC_NSEG - 1) * PAGE_SIZE); } #if defined(__NetBSD__) minphys(bp); #endif } /* * start a scsi operation given the command and * the data address, target, and lun all of which * are stored in the scsi_xfer struct */ static int32_t ahc_scsi_cmd(xs) struct scsi_xfer *xs; { struct scb *scb; struct hardware_scb *hscb; struct ahc_softc *ahc; u_int16_t mask; int flags; int s; ahc = (struct ahc_softc *)xs->sc_link->adapter_softc; mask = (0x01 << (xs->sc_link->target | (IS_SCSIBUS_B(ahc, xs->sc_link) ? SELBUSB : 0))); SC_DEBUG(xs->sc_link, SDEV_DB2, ("ahc_scsi_cmd\n")); flags = xs->flags; if (ahc->in_reset != 0) { /* * If we are still in a reset, send the transaction * back indicating that it was aborted due to a * reset. */ if ((IS_SCSIBUS_B(ahc, xs->sc_link) && (ahc->in_reset & CHANNEL_B_RESET) != 0) || (!IS_SCSIBUS_B(ahc, xs->sc_link) && (ahc->in_reset & CHANNEL_A_RESET) != 0)) { /* Ick, but I don't want it to abort this */ xs->retries++; xs->error = XS_BUSY; return(COMPLETE); } } /* * get an scb to use. If the transfer * is from a buf (possibly from interrupt time) * then we can't allow it to sleep */ if ((scb = ahc_get_scb(ahc, flags)) == NULL) { xs->error = XS_DRIVER_STUFFUP; return (TRY_AGAIN_LATER); } hscb = scb->hscb; SC_DEBUG(xs->sc_link, SDEV_DB3, ("start scb(%p)\n", scb)); scb->xs = xs; /* * Put all the arguments for the xfer in the scb */ if (ahc->discenable & mask) { hscb->control |= DISCENB; if (ahc->tagenable & mask) hscb->control |= MSG_SIMPLE_Q_TAG; if (ahc->orderedtag & mask) { /* XXX this should be handled by the upper SCSI layer */ printf("Ordered Tag sent\n"); hscb->control |= MSG_ORDERED_Q_TAG; ahc->orderedtag &= ~mask; } } if (flags & SCSI_RESET) { scb->flags |= SCB_DEVICE_RESET; hscb->control |= MK_MESSAGE; } else if ((ahc->needwdtr & mask) && !(ahc->wdtrpending & mask)) { ahc->wdtrpending |= mask; hscb->control |= MK_MESSAGE; scb->flags |= SCB_MSGOUT_WDTR; } else if((ahc->needsdtr & mask) && !(ahc->sdtrpending & mask)) { ahc->sdtrpending |= mask; hscb->control |= MK_MESSAGE; scb->flags |= SCB_MSGOUT_SDTR; } #if 0 /* Set the trace flag if this is the target we want to trace */ if (ahc->unit == 2 && xs->sc_link->target == 3) hscb->control |= TRACE_SCB; #endif hscb->tcl = ((xs->sc_link->target << 4) & 0xF0) | (IS_SCSIBUS_B(ahc,xs->sc_link)? SELBUSB : 0) | (xs->sc_link->lun & 0x07); hscb->cmdlen = xs->cmdlen; hscb->cmdpointer = vtophys(xs->cmd); xs->resid = 0; xs->status = 0; /* Only use S/G if non-zero length */ if (xs->datalen) { int seg; u_int32_t datalen; vm_offset_t vaddr; u_int32_t paddr; u_int32_t nextpaddr; struct ahc_dma_seg *sg; seg = 0; datalen = xs->datalen; vaddr = (vm_offset_t)xs->data; paddr = vtophys(vaddr); sg = scb->ahc_dma; hscb->SG_list_pointer = vtophys(sg); while ((datalen > 0) && (seg < AHC_NSEG)) { /* put in the base address and length */ sg->addr = paddr; sg->len = 0; /* do it at least once */ nextpaddr = paddr; while ((datalen > 0) && (paddr == nextpaddr)) { u_int32_t size; /* * This page is contiguous (physically) * with the the last, just extend the * length */ /* how far to the end of the page */ nextpaddr = (paddr & (~PAGE_MASK)) + PAGE_SIZE; /* * Compute the maximum size */ size = nextpaddr - paddr; if (size > datalen) size = datalen; sg->len += size; vaddr += size; datalen -= size; if (datalen > 0) paddr = vtophys(vaddr); } /* * next page isn't contiguous, finish the seg */ seg++; sg++; } hscb->SG_segment_count = seg; scb->sg_count = hscb->SG_segment_count; /* Copy the first SG into the data pointer area */ hscb->data = scb->ahc_dma->addr; hscb->datalen = scb->ahc_dma->len | (SCB_LIST_NULL << 24); if (datalen) { /* there's still data, must have run out of segs! */ printf("%s: ahc_scsi_cmd: more than %d DMA segs\n", ahc_name(ahc), AHC_NSEG); xs->error = XS_DRIVER_STUFFUP; ahc_free_scb(ahc, scb); return (COMPLETE); } #ifdef AHC_BROKEN_CACHE if (ahc_broken_cache) INVALIDATE_CACHE(); #endif } else { /* * No data xfer, use non S/G values */ hscb->SG_segment_count = 0; scb->sg_count = hscb->SG_segment_count; hscb->SG_list_pointer = 0; hscb->data = 0; hscb->datalen = (SCB_LIST_NULL << 24); } #ifdef AHC_DEBUG if((ahc_debug & AHC_SHOWSCBS) && (xs->sc_link->target == DEBUGTARGET)) ahc_print_scb(scb); #endif s = splbio(); STAILQ_INSERT_TAIL(&ahc->waiting_scbs, scb, links); scb->flags |= SCB_ACTIVE|SCB_WAITINGQ; ahc_run_waiting_queue(ahc); if ((flags & SCSI_NOMASK) == 0) { timeout(ahc_timeout, (caddr_t)scb, (xs->timeout * hz) / 1000); splx(s); return (SUCCESSFULLY_QUEUED); } /* * If we can't use interrupts, poll for completion */ SC_DEBUG(xs->sc_link, SDEV_DB3, ("cmd_poll\n")); do { if (ahc_poll(ahc, xs->timeout)) { if (!(xs->flags & SCSI_SILENT)) printf("cmd fail\n"); ahc_timeout(scb); break; } } while ((xs->flags & ITSDONE) == 0); /* a non command complete intr */ scsi_done(xs); splx(s); return (COMPLETE); } /* * Look for space in the QINFIFO and queue as many SCBs in the waiting * queue as possible. Assumes that it is called at splbio(). */ static void ahc_run_waiting_queue(ahc) struct ahc_softc *ahc; { struct scb *scb; pause_sequencer(ahc); while ((scb = ahc->waiting_scbs.stqh_first) != NULL) { if (ahc->curqincnt >= ahc->qfullcount) { ahc->curqincnt = ahc_inb(ahc, QINCNT) & ahc->qcntmask; if (ahc->curqincnt >= ahc->qfullcount) /* Still no space */ break; } STAILQ_REMOVE_HEAD(&ahc->waiting_scbs, links); scb->flags &= ~SCB_WAITINGQ; ahc_outb(ahc, QINFIFO, scb->hscb->tag); if ((ahc->flags & AHC_PAGESCBS) != 0) /* * We only care about this statistic when paging * since it is impossible to overflow the qinfifo * in the non-paging case. */ ahc->curqincnt++; } unpause_sequencer(ahc, /*Unpause always*/FALSE); } /* * An scb (and hence an scb entry on the board) is put onto the * free list. */ static void ahc_free_scb(ahc, scb) struct ahc_softc *ahc; struct scb *scb; { struct hardware_scb *hscb; int opri; hscb = scb->hscb; opri = splbio(); /* Clean up for the next user */ scb->flags = SCB_FREE; hscb->control = 0; hscb->status = 0; STAILQ_INSERT_HEAD(&ahc->scb_data->free_scbs, scb, links); if (scb->links.stqe_next == NULL) { /* * If there were no SCBs available, wake anybody waiting * for one to come free. */ wakeup((caddr_t)&ahc->scb_data->free_scbs); } #ifdef AHC_DEBUG ahc->activescbs--; #endif splx(opri); } /* * Get a free scb, either one already assigned to a hardware slot * on the adapter or one that will require an SCB to be paged out before * use. If there are none, see if we can allocate a new SCB. Otherwise * either return an error or sleep. */ static struct scb * ahc_get_scb(ahc, flags) struct ahc_softc *ahc; u_int32_t flags; { struct scb *scbp; int opri; opri = splbio(); /* * If we can and have to, sleep waiting for one to come free * but only if we can't allocate a new one. */ while (1) { if ((scbp = ahc->scb_data->free_scbs.stqh_first)) { STAILQ_REMOVE_HEAD(&ahc->scb_data->free_scbs, links); } else if(ahc->scb_data->numscbs < ahc->scb_data->maxscbs) { scbp = ahc_alloc_scb(ahc); if (scbp == NULL) printf("%s: Can't malloc SCB\n", ahc_name(ahc)); } else if ((flags & SCSI_NOSLEEP) == 0) { tsleep((caddr_t)&ahc->scb_data->free_scbs, PRIBIO, "ahcscb", 0); continue; } break; } #ifdef AHC_DEBUG if (scbp) { ahc->activescbs++; if((ahc_debug & AHC_SHOWSCBCNT) && (ahc->activescbs == ahc->scb_data->maxhscbs)) printf("%s: Max SCBs active\n", ahc_name(ahc)); } #endif splx(opri); return (scbp); } static struct scb * ahc_alloc_scb(ahc) struct ahc_softc *ahc; { static struct ahc_dma_seg *next_sg_array = NULL; static int sg_arrays_free = 0; struct scb *newscb; newscb = (struct scb *) malloc(sizeof(struct scb), M_DEVBUF, M_NOWAIT); if (newscb != NULL) { bzero(newscb, sizeof(struct scb)); if (next_sg_array == NULL) { size_t alloc_size = sizeof(struct ahc_dma_seg) * AHC_NSEG; sg_arrays_free = PAGE_SIZE / alloc_size; alloc_size *= sg_arrays_free; if (alloc_size == 0) panic("%s: SG list doesn't fit in a page", ahc_name(ahc)); next_sg_array = (struct ahc_dma_seg *) malloc(alloc_size, M_DEVBUF, M_NOWAIT); } if (next_sg_array != NULL) { struct hardware_scb *hscb; newscb->ahc_dma = next_sg_array; sg_arrays_free--; if (sg_arrays_free == 0) next_sg_array = NULL; else next_sg_array = &next_sg_array[AHC_NSEG]; hscb = &ahc->scb_data->hscbs[ahc->scb_data->numscbs]; newscb->hscb = hscb; hscb->control = 0; hscb->status = 0; hscb->tag = ahc->scb_data->numscbs; hscb->residual_data_count[2] = 0; hscb->residual_data_count[1] = 0; hscb->residual_data_count[0] = 0; hscb->residual_SG_segment_count = 0; ahc->scb_data->numscbs++; /* * Place in the scbarray * Never is removed. */ ahc->scb_data->scbarray[hscb->tag] = newscb; } else { free(newscb, M_DEVBUF); newscb = NULL; } } return newscb; } static void ahc_loadseq(ahc) struct ahc_softc *ahc; { int options; struct patch *cur_patch; int i; int downloaded; options = 1; /* Code for all options */ downloaded = 0; if ((ahc->type & AHC_ULTRA) != 0) options |= ULTRA; if ((ahc->type & AHC_TWIN) != 0) options |= TWIN_CHANNEL; if (ahc->scb_data->maxscbs > ahc->scb_data->maxhscbs) options |= SCB_PAGING; cur_patch = patches; ahc_outb(ahc, SEQCTL, PERRORDIS|LOADRAM); ahc_outb(ahc, SEQADDR0, 0); ahc_outb(ahc, SEQADDR1, 0); for(i = 0; i < sizeof(seqprog)/4; i++) { cur_patch = ahc_next_patch(cur_patch, options, i); if (cur_patch && cur_patch->begin <= i && cur_patch->end > i) /* Skip this instruction for this configuration */ continue; ahc_download_instr(ahc, options, i); downloaded++; } ahc_outb(ahc, SEQCTL, FASTMODE); ahc_outb(ahc, SEQADDR0, 0); ahc_outb(ahc, SEQADDR1, 0); if (bootverbose) printf("%s: %d instructions downloaded\n", ahc_name(ahc), downloaded); } static struct patch * ahc_next_patch(cur_patch, options, instrptr) struct patch *cur_patch; int options; int instrptr; { while(cur_patch != NULL) { if (((cur_patch->options & options) != 0 && cur_patch->negative == FALSE) || ((cur_patch->options & options) == 0 && cur_patch->negative == TRUE) || (instrptr >= cur_patch->end)) { /* * Either we want to keep this section of code, * or we have consumed this patch. Skip to the * next patch. */ cur_patch++; if (cur_patch->options == 0) /* Out of patches */ cur_patch = NULL; } else /* Found an okay patch */ break; } return (cur_patch); } static void ahc_download_instr(ahc, options, instrptr) struct ahc_softc *ahc; int options; int instrptr; { u_int8_t opcode; struct ins_format3 *instr; instr = (struct ins_format3 *)&seqprog[instrptr * 4]; /* Pull the opcode */ opcode = instr->opcode_addr >> 1; switch (opcode) { case AIC_OP_JMP: case AIC_OP_JC: case AIC_OP_JNC: case AIC_OP_CALL: case AIC_OP_JNE: case AIC_OP_JNZ: case AIC_OP_JE: case AIC_OP_JZ: { int address_offset; struct ins_format3 new_instr; u_int address; struct patch *patch; int i; address_offset = 0; new_instr = *instr; /* structure copy */ address = new_instr.address; address |= (new_instr.opcode_addr & ADDR_HIGH_BIT) << 8; for (i = 0; i < sizeof(patches)/sizeof(patches[0]); i++) { patch = &patches[i]; if (((patch->options & options) == 0 && patch->negative == FALSE) || ((patch->options & options) != 0 && patch->negative == TRUE)) { if (address >= patch->end) address_offset += patch->end - patch->begin; } } address -= address_offset; new_instr.address = address & 0xFF; new_instr.opcode_addr &= ~ADDR_HIGH_BIT; new_instr.opcode_addr |= (address >> 8) & ADDR_HIGH_BIT; ahc_outsb(ahc, SEQRAM, &new_instr.immediate, 4); break; } case AIC_OP_OR: case AIC_OP_AND: case AIC_OP_XOR: case AIC_OP_ADD: case AIC_OP_ADC: case AIC_OP_ROL: ahc_outsb(ahc, SEQRAM, &instr->immediate, 4); break; default: panic("Unknown opcode encountered in seq program"); break; } } /* * Function to poll for command completion when * interrupts are disabled (crash dumps) */ static int ahc_poll(ahc, wait) struct ahc_softc *ahc; int wait; /* in msec */ { while (--wait) { DELAY(1000); if (ahc_inb(ahc, INTSTAT) & INT_PEND) break; } if (wait == 0) { printf("%s: board is not responding\n", ahc_name(ahc)); return (EIO); } ahc_intr((void *)ahc); return (0); } /* * Handler to register that the system is capable of * delivering timeouts. We register this timeout in * ahc_init and it should go off as soon as we're through * the boot process. */ static void ahc_first_timeout(arg) void *arg; { timeouts_work = 1; } static void ahc_timeout(arg) void *arg; { struct scb *scb = (struct scb *)arg; struct ahc_softc *ahc; int s, found; u_int8_t bus_state; char channel; ahc = (struct ahc_softc *)scb->xs->sc_link->adapter_softc; s = splbio(); /* * Ensure that the card doesn't do anything * behind our back. Also make sure that we * didn't "just" miss an interrupt that would * affect this timeout. */ do { ahc_intr(ahc); pause_sequencer(ahc); } while (ahc_inb(ahc, INTSTAT) & INT_PEND); if (!(scb->flags & SCB_ACTIVE)) { /* Previous timeout took care of me already */ printf("Timedout SCB handled by another timeout\n"); unpause_sequencer(ahc, /*unpause_always*/TRUE); splx(s); return; } if (ahc->in_timeout) { /* * Some other SCB has started a recovery operation * and is still working on cleaning things up. */ if ((scb->flags & SCB_RECOVERY_SCB) == 0) { /* * This is not the SCB that started this timeout * processing. Give this scb another lifetime so * that it can continue once we deal with the * timeout. */ scb->flags |= SCB_TIMEDOUT; sc_print_addr(scb->xs->sc_link); printf("SCB 0x%x timedout while recovery in progress\n", scb->hscb->tag); timeout(ahc_timeout, (caddr_t)scb, (scb->xs->timeout * hz) / 1000); unpause_sequencer(ahc, /*unpause_always*/TRUE); splx(s); return; } } ahc->in_timeout = TRUE; sc_print_addr(scb->xs->sc_link); printf("SCB 0x%x - timed out ", scb->hscb->tag); /* * Take a snapshot of the bus state and print out * some information so we can track down driver bugs. */ bus_state = ahc_inb(ahc, LASTPHASE); switch(bus_state) { case P_DATAOUT: printf("in dataout phase"); break; case P_DATAIN: printf("in datain phase"); break; case P_COMMAND: printf("in command phase"); break; case P_MESGOUT: printf("in message out phase"); break; case P_STATUS: printf("in status phase"); break; case P_MESGIN: printf("in message in phase"); break; case P_BUSFREE: printf("while idle, LASTPHASE == 0x%x", bus_state); break; default: /* * We aren't in a valid phase, so assume we're * idle. */ printf("invalid phase, LASTPHASE == 0x%x", bus_state); break; } printf(", SCSISIGI == 0x%x\n", ahc_inb(ahc, SCSISIGI)); printf("SEQADDR = 0x%x SCSISEQ = 0x%x SSTAT0 = 0x%x SSTAT1 = 0x%x\n", ahc_inb(ahc, SEQADDR0) | (ahc_inb(ahc, SEQADDR1) << 8), ahc_inb(ahc, SCSISEQ), ahc_inb(ahc, SSTAT0), ahc_inb(ahc,SSTAT1)); /* Decide our course of action */ channel = (scb->hscb->tcl & SELBUSB) ? 'B': 'A'; if (scb->flags & SCB_ABORT) { /* * Been down this road before. * Do a full bus reset. */ bus_reset: scb->flags |= SCB_RECOVERY_SCB; found = ahc_reset_channel(ahc, channel, XS_TIMEOUT, /*Initiate Reset*/TRUE); printf("%s: Issued Channel %c Bus Reset. " "%d SCBs aborted\n", ahc_name(ahc), channel, found); } else if ((scb->hscb->control & TAG_ENB) != 0 && (scb->flags & SCB_SENTORDEREDTAG) == 0) { /* * We could be starving this command * try sending an ordered tag command * to the target we come from. */ u_int16_t mask; mask = (0x01 << (scb->xs->sc_link->target | (IS_SCSIBUS_B(ahc, scb->xs->sc_link) ? SELBUSB : 0))); scb->flags |= SCB_SENTORDEREDTAG|SCB_RECOVERY_SCB; ahc->orderedtag |= mask; timeout(ahc_timeout, (caddr_t)scb, (5 * hz)); unpause_sequencer(ahc, /*unpause_always*/TRUE); printf("Ordered Tag queued\n"); } else { /* * Send an Abort Message: * The target that is holding up the bus may not * be the same as the one that triggered this timeout * (different commands have different timeout lengths). * Our strategy here is to queue an abort message * to the timed out target if it is disconnected. * Otherwise, if we have an active target we stuff the * message buffer with an abort message and assert ATN * in the hopes that the target will let go of the bus * and go to the mesgout phase. If this fails, we'll * get another timeout 2 seconds later which will attempt * a bus reset. */ u_int8_t saved_scbptr; u_int8_t active_scb_index; struct scb *active_scb; saved_scbptr = ahc_inb(ahc, SCBPTR); active_scb_index = ahc_inb(ahc, SCB_TAG); active_scb = ahc->scb_data->scbarray[active_scb_index]; if (bus_state != P_BUSFREE) { if (active_scb_index >= ahc->scb_data->numscbs) { /* Go "immediatly" to the bus reset */ /* * XXX queue an abort for the timedout SCB * instead. */ sc_print_addr(scb->xs->sc_link); printf("SCB %d: Yucky Immediate reset. " "Flags = 0x%x\n", scb->hscb->tag, scb->flags); goto bus_reset; } /* Send the abort to the active SCB */ ahc_outb(ahc, MSG_LEN, 1); ahc_outb(ahc, MSG_OUT, (active_scb->hscb->control & TAG_ENB) == 0 ? MSG_ABORT : MSG_ABORT_TAG); ahc_outb(ahc, SCSISIGO, bus_state|ATNO); sc_print_addr(active_scb->xs->sc_link); printf("abort message in message buffer\n"); active_scb->flags |= SCB_ABORT|SCB_RECOVERY_SCB; if (active_scb != scb) { untimeout(ahc_timeout, (caddr_t)active_scb); /* Give scb a new lease on life */ timeout(ahc_timeout, (caddr_t)scb, (scb->xs->timeout * hz) / 1000); } timeout(ahc_timeout, (caddr_t)active_scb, (200 * hz) / 1000); unpause_sequencer(ahc, /*unpause_always*/TRUE); } else { int disconnected; u_int8_t hscb_index; u_int8_t linked_next; disconnected = FALSE; hscb_index = ahc_find_scb(ahc, scb); if (hscb_index == SCB_LIST_NULL) { disconnected = TRUE; linked_next = (scb->hscb->datalen >> 24) & 0xFF; } else { ahc_outb(ahc, SCBPTR, hscb_index); if (ahc_inb(ahc, SCB_CONTROL) & DISCONNECTED) disconnected = TRUE; linked_next = ahc_inb(ahc, SCB_LINKED_NEXT); } if (disconnected) { /* * Simply set the ABORT_SCB control bit * and preserve the linked next pointer */ scb->hscb->control |= ABORT_SCB|MK_MESSAGE; scb->hscb->datalen &= ~0xFF000000; scb->hscb->datalen |= linked_next << 24; if ((ahc->flags & AHC_PAGESCBS) == 0) scb->hscb->control &= ~DISCONNECTED; scb->flags |= SCB_QUEUED_ABORT | SCB_ABORT|SCB_RECOVERY_SCB; if (hscb_index != SCB_LIST_NULL) { u_int8_t scb_control; scb_control = ahc_inb(ahc, SCB_CONTROL); ahc_outb(ahc, SCB_CONTROL, scb_control | MK_MESSAGE | ABORT_SCB); } /* * Actually re-queue this SCB in case we can * select the device before it reconnects. If * the transaction we want to abort is not * tagged, unbusy it first so that we don't * get held back from sending the command. */ if ((scb->hscb->control & TAG_ENB) == 0) { int target; int lun; target = scb->xs->sc_link->target; lun = scb->xs->sc_link->lun; ahc_search_qinfifo(ahc, target, channel, lun, SCB_LIST_NULL, 0, 0, /*requeue*/TRUE); } sc_print_addr(scb->xs->sc_link); printf("Queueing an Abort SCB\n"); STAILQ_INSERT_HEAD(&ahc->waiting_scbs, scb, links); scb->flags |= SCB_WAITINGQ; timeout(ahc_timeout, (caddr_t)scb, (200 * hz) / 1000); ahc_outb(ahc, SCBPTR, saved_scbptr); /* * ahc_run_waiting_queue may unpause us * so do this last. */ ahc_run_waiting_queue(ahc); /* * If we are using AAP, ahc_run_waiting_queue * will not unpause us, so ensure we are * unpaused. */ unpause_sequencer(ahc, /*unpause_always*/FALSE); } else { /* Go "immediatly" to the bus reset */ sc_print_addr(scb->xs->sc_link); printf("SCB %d: Immediate reset. " "Flags = 0x%x\n", scb->hscb->tag, scb->flags); goto bus_reset; } } } splx(s); } /* * Look through the SCB array of the card and attempt to find the * hardware SCB that corresponds to the passed in SCB. Return * SCB_LIST_NULL if unsuccessful. This routine assumes that the * card is already paused. */ static u_int8_t ahc_find_scb(ahc, scb) struct ahc_softc *ahc; struct scb *scb; { u_int8_t saved_scbptr; u_int8_t curindex; saved_scbptr = ahc_inb(ahc, SCBPTR); for (curindex = 0; curindex < ahc->scb_data->maxhscbs; curindex++) { ahc_outb(ahc, SCBPTR, curindex); if (ahc_inb(ahc, SCB_TAG) == scb->hscb->tag) break; } ahc_outb(ahc, SCBPTR, saved_scbptr); if (curindex >= ahc->scb_data->maxhscbs) curindex = SCB_LIST_NULL; return curindex; } static int ahc_search_qinfifo(ahc, target, channel, lun, tag, flags, xs_error, requeue) struct ahc_softc *ahc; int target; char channel; int lun; u_int8_t tag; u_int32_t flags; u_int32_t xs_error; int requeue; { u_int8_t saved_queue[AHC_SCB_MAX]; int queued = ahc_inb(ahc, QINCNT) & ahc->qcntmask; int i; int found; struct scb *scbp; STAILQ_HEAD(, scb) removed_scbs; found = 0; STAILQ_INIT(&removed_scbs); for (i = 0; i < (queued - found); i++) { saved_queue[i] = ahc_inb(ahc, QINFIFO); scbp = ahc->scb_data->scbarray[saved_queue[i]]; if (ahc_match_scb(scbp, target, channel, lun, tag)) { /* * We found an scb that needs to be removed. */ if (requeue) { STAILQ_INSERT_HEAD(&removed_scbs, scbp, links); } else { scbp->flags |= flags; scbp->flags &= ~SCB_ACTIVE; scbp->xs->error = xs_error; } i--; found++; } } /* Now put the saved scbs back. */ for (queued = 0; queued < i; queued++) ahc_outb(ahc, QINFIFO, saved_queue[queued]); if (requeue) { while ((scbp = removed_scbs.stqh_first) != NULL) { STAILQ_REMOVE_HEAD(&removed_scbs, links); STAILQ_INSERT_HEAD(&ahc->waiting_scbs, scbp, links); scbp->flags |= SCB_WAITINGQ; } } return found; } /* * The device at the given target/channel has been reset. Abort * all active and queued scbs for that target/channel. */ static int ahc_reset_device(ahc, target, channel, lun, tag, xs_error) struct ahc_softc *ahc; int target; char channel; int lun; u_int8_t tag; u_int32_t xs_error; { struct scb *scbp; u_int8_t active_scb; int i; int found; /* restore this when we're done */ active_scb = ahc_inb(ahc, SCBPTR); /* * Deal with the busy target and linked next issues. */ { int min_target, max_target; u_int8_t busy_scbid; /* Make all targets 'relative' to bus A */ if (target == ALL_TARGETS) { switch (channel) { case 'A': min_target = 0; max_target = ahc->type & AHC_WIDE ? 15 : 7; break; case 'B': min_target = 8; max_target = 15; break; case ALL_CHANNELS: min_target = 0; max_target = ahc->type & AHC_WIDE|AHC_TWIN ? 15 : 7; break; } } else { min_target = max_target = target + channel == 'B' ? 8 : 0; } for (i = min_target; i <= max_target; i++) { busy_scbid = ahc_index_busy_target(ahc, i, 'A', /*unbusy*/FALSE); if (busy_scbid < ahc->scb_data->numscbs) { struct scb *busy_scb; struct scb *next_scb; u_int8_t next_scbid; busy_scb = ahc->scb_data->scbarray[busy_scbid]; next_scbid = busy_scb->hscb->datalen >> 24; if (next_scbid == SCB_LIST_NULL) { busy_scbid = ahc_find_scb(ahc, busy_scb); if (busy_scbid != SCB_LIST_NULL) { ahc_outb(ahc, SCBPTR, busy_scbid); next_scbid = ahc_inb(ahc, SCB_LINKED_NEXT); } } if (ahc_match_scb(busy_scb, target, channel, lun, tag)) { ahc_index_busy_target(ahc, i, 'A', /*unbusy*/TRUE); } if (next_scbid != SCB_LIST_NULL) { next_scb = ahc->scb_data->scbarray[next_scbid]; if (ahc_match_scb(next_scb, target, channel, lun, tag)) continue; /* Requeue for later processing */ STAILQ_INSERT_HEAD(&ahc->waiting_scbs, next_scb, links); next_scb->flags |= SCB_WAITINGQ; } } } } /* * Remove any entries from the Queue-In FIFO. */ found = ahc_search_qinfifo(ahc, target, channel, lun, tag, SCB_ABORTED|SCB_QUEUED_FOR_DONE, xs_error, /*requeue*/FALSE); /* * Search waiting for selection list. */ { u_int8_t next, prev; next = ahc_inb(ahc, WAITING_SCBH); /* Start at head of list. */ prev = SCB_LIST_NULL; while (next != SCB_LIST_NULL) { u_int8_t scb_index; ahc_outb(ahc, SCBPTR, next); scb_index = ahc_inb(ahc, SCB_TAG); if (scb_index >= ahc->scb_data->numscbs) { panic("Waiting List inconsistency. " "SCB index == %d, yet numscbs == %d.", scb_index, ahc->scb_data->numscbs); } scbp = ahc->scb_data->scbarray[scb_index]; if (ahc_match_scb(scbp, target, channel, lun, tag)) { u_int8_t linked_next; next = ahc_abort_wscb(ahc, scbp, next, prev, xs_error); linked_next = ahc_inb(ahc, SCB_LINKED_NEXT); if (linked_next != SCB_LIST_NULL) { struct scb *next_scb; /* * Re-queue the waiting SCB via the * waiting list. */ next_scb = ahc->scb_data->scbarray[linked_next]; if (!ahc_match_scb(next_scb, target, channel, lun, tag)) { STAILQ_INSERT_HEAD(&ahc->waiting_scbs, next_scb, links); next_scb->flags |= SCB_WAITINGQ; } } found++; } else { prev = next; next = ahc_inb(ahc, SCB_NEXT); } } } /* * Go through the disconnected list and remove any entries we * have queued for completion, 0'ing their control byte too. */ { u_int8_t next, prev; next = ahc_inb(ahc, DISCONNECTED_SCBH); prev = SCB_LIST_NULL; while (next != SCB_LIST_NULL) { u_int8_t scb_index; ahc_outb(ahc, SCBPTR, next); scb_index = ahc_inb(ahc, SCB_TAG); if (scb_index >= ahc->scb_data->numscbs) { panic("Disconnected List inconsistency. " "SCB index == %d, yet numscbs == %d.", scb_index, ahc->scb_data->numscbs); } scbp = ahc->scb_data->scbarray[scb_index]; if (ahc_match_scb(scbp, target, channel, lun, tag)) { next = ahc_rem_scb_from_disc_list(ahc, next); } else { prev = next; next = ahc_inb(ahc, SCB_NEXT); } } } /* * Go through the hardware SCB array looking for commands that * were active but not on any list. */ for(i = 0; i < ahc->scb_data->maxhscbs; i++) { u_int8_t scbid; ahc_outb(ahc, SCBPTR, i); scbid = ahc_inb(ahc, SCB_TAG); if (scbid < ahc->scb_data->numscbs) { scbp = ahc->scb_data->scbarray[scbid]; if (ahc_match_scb(scbp, target, channel, lun, tag)) { ahc_add_curscb_to_free_list(ahc); } } } /* * Go through the entire SCB array now and look for * commands for this target that are still active. These * are other tagged commands that were disconnected when * the reset occured or untagged commands that were linked * to the command that preceeded it. */ for (i = 0; i < ahc->scb_data->numscbs; i++) { scbp = ahc->scb_data->scbarray[i]; if ((scbp->flags & SCB_ACTIVE) != 0 && ahc_match_scb(scbp, target, channel, lun, tag)) { scbp->flags |= SCB_ABORTED|SCB_QUEUED_FOR_DONE; scbp->flags &= ~SCB_ACTIVE; scbp->xs->error = xs_error; found++; if ((scbp->flags & SCB_WAITINGQ) != 0) { STAILQ_REMOVE(&ahc->waiting_scbs, scbp, scb, links); scbp->flags &= ~SCB_WAITINGQ; } } } ahc_outb(ahc, SCBPTR, active_scb); return found; } static u_int8_t ahc_rem_scb_from_disc_list(ahc, scbptr) struct ahc_softc *ahc; u_int8_t scbptr; { u_int8_t next; u_int8_t prev; ahc_outb(ahc, SCBPTR, scbptr); next = ahc_inb(ahc, SCB_NEXT); prev = ahc_inb(ahc, SCB_PREV); ahc_outb(ahc, SCB_CONTROL, 0); ahc_add_curscb_to_free_list(ahc); if (prev != SCB_LIST_NULL) { ahc_outb(ahc, SCBPTR, prev); ahc_outb(ahc, SCB_NEXT, next); } else ahc_outb(ahc, DISCONNECTED_SCBH, next); if (next != SCB_LIST_NULL) { ahc_outb(ahc, SCBPTR, next); ahc_outb(ahc, SCB_PREV, prev); } return next; } static void ahc_add_curscb_to_free_list(ahc) struct ahc_softc *ahc; { /* Invalidate the tag so that ahc_find_scb doesn't think it's active */ ahc_outb(ahc, SCB_TAG, SCB_LIST_NULL); ahc_outb(ahc, SCB_NEXT, ahc_inb(ahc, FREE_SCBH)); ahc_outb(ahc, FREE_SCBH, ahc_inb(ahc, SCBPTR)); } /* * Manipulate the waiting for selection list and return the * scb that follows the one that we remove. */ static u_char ahc_abort_wscb (ahc, scbp, scbpos, prev, xs_error) struct ahc_softc *ahc; struct scb *scbp; u_int8_t scbpos; u_int8_t prev; u_int32_t xs_error; { u_int8_t curscb, next; int target = ((scbp->hscb->tcl >> 4) & 0x0f); char channel = (scbp->hscb->tcl & SELBUSB) ? 'B' : 'A'; /* * Select the SCB we want to abort and * pull the next pointer out of it. */ curscb = ahc_inb(ahc, SCBPTR); ahc_outb(ahc, SCBPTR, scbpos); next = ahc_inb(ahc, SCB_NEXT); /* Clear the necessary fields */ ahc_outb(ahc, SCB_CONTROL, 0); ahc_add_curscb_to_free_list(ahc); /* update the waiting list */ if (prev == SCB_LIST_NULL) /* First in the list */ ahc_outb(ahc, WAITING_SCBH, next); else { /* * Select the scb that pointed to us * and update its next pointer. */ ahc_outb(ahc, SCBPTR, prev); ahc_outb(ahc, SCB_NEXT, next); } /* * Point us back at the original scb position * and inform the SCSI system that the command * has been aborted. */ ahc_outb(ahc, SCBPTR, curscb); scbp->flags |= SCB_ABORTED|SCB_QUEUED_FOR_DONE; scbp->flags &= ~SCB_ACTIVE; scbp->xs->error = xs_error; return next; } static u_int8_t ahc_index_busy_target(ahc, target, channel, unbusy) struct ahc_softc *ahc; int target; char channel; int unbusy; { u_int8_t active_scb; u_int8_t info_scb; u_int8_t busy_scbid; u_int32_t scb_offset; info_scb = target / 4; if (channel == 'B') info_scb += 2; active_scb = ahc_inb(ahc, SCBPTR); ahc_outb(ahc, SCBPTR, info_scb); scb_offset = SCB_BUSYTARGETS + (target & 0x03); busy_scbid = ahc_inb(ahc, scb_offset); if (unbusy) ahc_outb(ahc, scb_offset, SCB_LIST_NULL); ahc_outb(ahc, SCBPTR, active_scb); return busy_scbid; } static void ahc_busy_target(ahc, target, channel, scbid) struct ahc_softc *ahc; int target; char channel; u_int8_t scbid; { u_int8_t active_scb; u_int8_t info_scb; u_int8_t busy_scbid; u_int32_t scb_offset; info_scb = target / 4; if (channel == 'B') info_scb += 2; active_scb = ahc_inb(ahc, SCBPTR); ahc_outb(ahc, SCBPTR, info_scb); scb_offset = SCB_BUSYTARGETS + (target & 0x03); ahc_outb(ahc, scb_offset, scbid); ahc_outb(ahc, SCBPTR, active_scb); return; } static void ahc_clear_intstat(ahc) struct ahc_softc *ahc; { /* Clear any interrupt conditions this may have caused */ ahc_outb(ahc, CLRSINT0, CLRSELDO|CLRSELDI|CLRSELINGO); ahc_outb(ahc, CLRSINT1, CLRSELTIMEO|CLRATNO|CLRSCSIRSTI |CLRBUSFREE|CLRSCSIPERR|CLRPHASECHG| CLRREQINIT); ahc_outb(ahc, CLRINT, CLRSCSIINT); } static void ahc_reset_current_bus(ahc) struct ahc_softc *ahc; { u_int8_t scsiseq; u_int8_t sblkctl; ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENSCSIRST); scsiseq = ahc_inb(ahc, SCSISEQ); ahc_outb(ahc, SCSISEQ, scsiseq | SCSIRSTO); if (timeouts_work != 0) { struct ahc_busreset_args *args; sblkctl = ahc_inb(ahc, SBLKCTL); args = (sblkctl & SELBUSB) ? &ahc->busreset_args_b : &ahc->busreset_args; ahc->in_reset |= (args->bus == 'A' ? CHANNEL_A_RESET : CHANNEL_B_RESET); timeout(ahc_busreset_complete, args, MAX((AHC_BUSRESET_DELAY * hz) / 1000000, 1)); } else { DELAY(AHC_BUSRESET_DELAY); /* Turn off the bus reset */ ahc_outb(ahc, SCSISEQ, scsiseq & ~SCSIRSTO); ahc_clear_intstat(ahc); /* Re-enable reset interrupts */ ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) | ENSCSIRST); /* Wait a minimal bus settle delay */ DELAY(AHC_BUSSETTLE_DELAY); ahc_run_done_queue(ahc); } } static void ahc_busreset_complete(arg) void *arg; { struct ahc_busreset_args *args; struct ahc_softc *ahc; int s; u_int8_t scsiseq; u_int8_t sblkctl; args = (struct ahc_busreset_args *)arg; ahc = (struct ahc_softc *)args->ahc; s = splbio(); pause_sequencer(ahc); /* Save the current block control state */ sblkctl = ahc_inb(ahc, SBLKCTL); /* Switch to the right bus */ if (args->bus == 'A') ahc_outb(ahc, SBLKCTL, sblkctl & ~SELBUSB); else ahc_outb(ahc, SBLKCTL, sblkctl | SELBUSB); /* Turn off the bus reset */ printf("Clearing bus reset\n"); scsiseq = ahc_inb(ahc, SCSISEQ); ahc_outb(ahc, SCSISEQ, scsiseq & ~SCSIRSTO); ahc_clear_intstat(ahc); /* Re-enable reset interrupts */ ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) | ENSCSIRST); /* * Set a 100ms timeout to clear our in_reset flag. * It will be *at-least* that long before any targets * respond to real commands on the bus. */ timeout(ahc_busreset_settle_complete, args, (AHC_BUSSETTLE_DELAY * hz) / 1000000); /* Restore the original channel */ ahc_outb(ahc, SBLKCTL, sblkctl); unpause_sequencer(ahc, /*unpause_always*/FALSE); splx(s); } static void ahc_busreset_settle_complete(arg) void *arg; { struct ahc_busreset_args *args; struct ahc_softc *ahc; int s; args = (struct ahc_busreset_args *)arg; ahc = (struct ahc_softc *)args->ahc; /* Clear the reset flag */ s = splbio(); printf("Clearing 'in-reset' flag\n"); ahc->in_reset &= (args->bus == 'A' ? ~CHANNEL_A_RESET : ~CHANNEL_B_RESET); ahc_run_done_queue(ahc); splx(s); } static int ahc_reset_channel(ahc, channel, xs_error, initiate_reset) struct ahc_softc *ahc; char channel; u_int32_t xs_error; int initiate_reset; { u_int32_t offset, offset_max; int found; int target; u_int8_t sblkctl; char cur_channel; pause_sequencer(ahc); /* * Clean up all the state information for the * pending transactions on this bus. */ found = ahc_reset_device(ahc, ALL_TARGETS, channel, ALL_LUNS, SCB_LIST_NULL, xs_error); if (channel == 'B') { ahc->needsdtr |= (ahc->needsdtr_orig & 0xff00); ahc->sdtrpending &= 0x00ff; ahc->orderedtag &= 0x00ff; offset = TARG_SCRATCH + 8; offset_max = TARG_SCRATCH + 16; } else if (ahc->type & AHC_WIDE){ ahc->needsdtr = ahc->needsdtr_orig; ahc->needwdtr = ahc->needwdtr_orig; ahc->orderedtag = 0; ahc->sdtrpending = 0; ahc->wdtrpending = 0; offset = TARG_SCRATCH; offset_max = TARG_SCRATCH + 16; } else { ahc->needsdtr |= (ahc->needsdtr_orig & 0x00ff); ahc->sdtrpending &= 0xff00; ahc->orderedtag &= 0xff00; offset = TARG_SCRATCH; offset_max = TARG_SCRATCH + 8; } for (; offset < offset_max; offset++) { /* * Revert to async/narrow transfers * until we renegotiate. */ u_int8_t targ_scratch; targ_scratch = ahc_inb(ahc, offset); targ_scratch &= SXFR; ahc_outb(ahc, offset, targ_scratch); } /* * Reset the bus if we are initiating this reset and * restart/unpause the sequencer */ sblkctl = ahc_inb(ahc, SBLKCTL); cur_channel = (sblkctl & SELBUSB) ? 'B' : 'A'; if (cur_channel != channel) { /* Case 1: Command for another bus is active * Stealthily reset the other bus without * upsetting the current bus. */ ahc_outb(ahc, SBLKCTL, sblkctl ^ SELBUSB); ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); if (initiate_reset) ahc_reset_current_bus(ahc); ahc_outb(ahc, SCSISEQ, 0); ahc_clear_intstat(ahc); ahc_outb(ahc, SBLKCTL, sblkctl); unpause_sequencer(ahc, /*unpause_always*/FALSE); } else { /* Case 2: A command from this bus is active or we're idle */ ahc_outb(ahc, SIMODE1, ahc_inb(ahc, SIMODE1) & ~ENBUSFREE); if (initiate_reset) ahc_reset_current_bus(ahc); ahc_outb(ahc, SCSISEQ, 0); ahc_clear_intstat(ahc); restart_sequencer(ahc); } /* * Untimeout our scbs now in case we have to delay our done * processing. */ ahc_untimeout_done_queue(ahc); if (initiate_reset == 0) { /* * If we initiated the reset, we'll run the queue * once our bus-settle delay has expired. */ ahc_run_done_queue(ahc); } return found; } static void ahc_run_done_queue(ahc) struct ahc_softc *ahc; { int i; struct scb *scbp; for (i = 0; i < ahc->scb_data->numscbs; i++) { scbp = ahc->scb_data->scbarray[i]; if (scbp->flags & SCB_QUEUED_FOR_DONE) ahc_done(ahc, scbp); } } static void ahc_untimeout_done_queue(ahc) struct ahc_softc *ahc; { int i; struct scb *scbp; for (i = 0; i < ahc->scb_data->numscbs; i++) { scbp = ahc->scb_data->scbarray[i]; if (scbp->flags & SCB_QUEUED_FOR_DONE) untimeout(ahc_timeout, (caddr_t)scbp); } } static int ahc_match_scb (scb, target, channel, lun, tag) struct scb *scb; int target; char channel; int lun; u_int8_t tag; { int targ = (scb->hscb->tcl >> 4) & 0x0f; char chan = (scb->hscb->tcl & SELBUSB) ? 'B' : 'A'; int slun = scb->hscb->tcl & 0x07; int match; match = ((chan == channel) || (channel == ALL_CHANNELS)); if (match != 0) match = ((targ == target) || (target == ALL_TARGETS)); if (match != 0) match = ((lun == slun) || (lun == ALL_LUNS)); if (match != 0) match = ((tag == scb->hscb->tag) || (tag == SCB_LIST_NULL)); return match; } static void ahc_construct_sdtr(ahc, start_byte, period, offset) struct ahc_softc *ahc; int start_byte; u_int8_t period; u_int8_t offset; { ahc_outb(ahc, MSG_OUT + start_byte, MSG_EXTENDED); ahc_outb(ahc, MSG_OUT + 1 + start_byte, MSG_EXT_SDTR_LEN); ahc_outb(ahc, MSG_OUT + 2 + start_byte, MSG_EXT_SDTR); ahc_outb(ahc, MSG_OUT + 3 + start_byte, period); ahc_outb(ahc, MSG_OUT + 4 + start_byte, offset); ahc_outb(ahc, MSG_LEN, start_byte + 5); } static void ahc_construct_wdtr(ahc, start_byte, bus_width) struct ahc_softc *ahc; int start_byte; u_int8_t bus_width; { ahc_outb(ahc, MSG_OUT + start_byte, MSG_EXTENDED); ahc_outb(ahc, MSG_OUT + 1 + start_byte, MSG_EXT_WDTR_LEN); ahc_outb(ahc, MSG_OUT + 2 + start_byte, MSG_EXT_WDTR); ahc_outb(ahc, MSG_OUT + 3 + start_byte, bus_width); ahc_outb(ahc, MSG_LEN, start_byte + 4); } static void ahc_calc_residual(scb) struct scb *scb; { struct scsi_xfer *xs; struct hardware_scb *hscb; int resid_sgs; xs = scb->xs; hscb = scb->hscb; /* * If the disconnected flag is still set, this is bogus * residual information left over from a sequencer * pagin/pageout, so ignore this case. */ if ((scb->hscb->control & DISCONNECTED) == 0 && (scb->flags & SCB_SENSE) == 0) { /* * Remainder of the SG where the transfer * stopped. */ xs->resid = (hscb->residual_data_count[2] <<16) | (hscb->residual_data_count[1] <<8) | (hscb->residual_data_count[0]); /* * Add up the contents of all residual * SG segments that are after the SG where * the transfer stopped. */ resid_sgs = scb->hscb->residual_SG_segment_count - 1; while (resid_sgs > 0) { int sg; sg = scb->sg_count - resid_sgs; xs->resid += scb->ahc_dma[sg].len; resid_sgs--; } #if defined(__FreeBSD__) xs->flags |= SCSI_RESID_VALID; #elif defined(__NetBSD__) /* XXX - Update to do this right */ #endif } /* * Clean out the residual information in this SCB for its * next consumer. */ hscb->residual_data_count[2] = 0; hscb->residual_data_count[1] = 0; hscb->residual_data_count[0] = 0; hscb->residual_SG_segment_count = 0; #ifdef AHC_DEBUG if (ahc_debug & AHC_SHOWMISC) { sc_print_addr(xs->sc_link); printf("Handled Residual of %ld bytes\n" ,xs->resid); } #endif }