.\" Copyright (C) 1995, 1996, 1997, and 1998 WIDE Project. .\" All rights reserved. .\" .\" Redistribution and use in source and binary forms, with or without .\" modification, are permitted provided that the following conditions .\" are met: .\" 1. Redistributions of source code must retain the above copyright .\" notice, this list of conditions and the following disclaimer. .\" 2. Redistributions in binary form must reproduce the above copyright .\" notice, this list of conditions and the following disclaimer in the .\" documentation and/or other materials provided with the distribution. .\" 3. Neither the name of the project nor the names of its contributors .\" may be used to endorse or promote products derived from this software .\" without specific prior written permission. .\" .\" THIS SOFTWARE IS PROVIDED BY THE PROJECT AND CONTRIBUTORS ``AS IS'' AND .\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE .\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE .\" ARE DISCLAIMED. IN NO EVENT SHALL THE PROJECT OR CONTRIBUTORS BE LIABLE .\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL .\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS .\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) .\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT .\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY .\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF .\" SUCH DAMAGE. .\" .\" $Id: inet6.4,v 1.1.1.1 1999/08/08 23:30:37 itojun Exp $ .\" $FreeBSD$ .\" .Dd January 29, 1999 .Dt INET6 4 .Os .Sh NAME .Nm inet6 .Nd Internet protocol version 6 family .Sh SYNOPSIS .Fd #include .Fd #include .Sh DESCRIPTION The .Nm family is an updated version of .Xr inet 4 family. While .Xr inet 4 implements Internet Protocol version 4, .Nm implements Internet Protocol version 6. .Pp .Nm is a collection of protocols layered atop the .Em Internet Protocol version 6 .Pq Tn IPv6 network layer, and utilizing the IPv6 address format. The .Nm family provides protocol support for the .Dv SOCK_STREAM , SOCK_DGRAM , and .Dv SOCK_RAW socket types; the .Dv SOCK_RAW interface provides access to the .Tn IPv6 protocol. .Sh ADDRESSING IPv6 addresses are 16 byte quantities, stored in network standard format. The include file .Aq Pa netinet/in.h defines this address as a discriminated union. .Pp Sockets bound to the .Nm family utilize the following addressing structure, .Bd -literal -offset indent struct sockaddr_in6 { u_char sin6_len; u_char sin6_family; u_int16_t sin6_port; u_int32_t sin6_flowinfo; struct in6_addr sin6_addr; u_int32_t sin6_scope_id; }; .Ed .Pp Sockets may be created with the local address .Dq Dv :: .Po which is equal to IPv6 address .Dv 0:0:0:0:0:0:0:0 .Pc to effect .Dq wildcard matching on incoming messages. The address in a .Xr connect 2 or .Xr sendto 2 call may be given as .Dq Dv :: to mean .Dq this host . The address .Dq Dv :: can be obtained by setting the .Dv sin6_addr field to 0, or by using the address contained in the variable .Dv in6addr_any . .Pp IPv6 defines scoped addresses such as link-local or site-local addresses. A scoped address is ambiguous to the kernel, if it is specified without a scope identifier. To manipulate scoped addresses properly from the userland, programs must use the advanced API defined in RFC2292. A compact description on the advanced API is available in .Xr ip6 4 . If scoped addresses are specified without explicit scope, and the IPv6 default interface for scoped addresses is not specified, an error, .Er EHOSTUNREACH , will be returned from the kernel. Note that scoped addresses are not for common use at this moment, both from specification and implementation point of view. .Pp FreeBSD's IPv6 implementation supports extended numeric IPv6 address notation for link-local addresses, like .Dq Li fe80::1%de0 to specify .Do .Li fe80::1 on the .Li de0 interface .Dc . This notation is supported by .Xr getaddrinfo 3 and .Xr getnameinfo 3 . Some of the normal userland programs, such as .Xr telnet 1 or .Xr ftp 8 , are able to use this notation. With some special programs such as .Xr ping6 8 , you can specify an outgoing interface by an extra command line option to disambiguate scoped addresses. .Pp Scoped addresses are handled specially in the kernel. Scoped addresses will have their interface indices embedded into the address, in the routing table or interface structures. Therefore, a scoped address may have a different representation in the kernel than on the wire. The embedded index will be visible in .Dv PF_ROUTE sockets, kernel memory accesses via .Xr kvm 3 and some other occasions. HOWEVER, users should never use the embedded form. For details, please consult .Pa IMPLEMENTATION supplied with the KAME kit. .Sh PROTOCOLS The .Nm family is comprised of the .Tn IPv6 network protocol, Internet Control Message Protocol version 6 .Pq Tn ICMPv6 , Transmission Control Protocol .Pq Tn TCP , and User Datagram Protocol .Pq Tn UDP . .Tn TCP is used to support the .Dv SOCK_STREAM abstraction while .Tn UDP is used to support the .Dv SOCK_DGRAM abstraction. Note that .Tn TCP and .Tn UDP are common to .Xr inet 4 and .Nm inet6 . A raw interface to .Tn IPv6 is available by creating an Internet socket of type .Dv SOCK_RAW . The .Tn ICMPv6 message protocol is accessible from a raw socket. .\" .Pp .\" The 128-bit IPv6 address contains both network and host parts. .\" However, direct examination of addresses is discouraged. .\" For those programs which absolutely need to break addresses .\" into their component parts, the following .\" .Xr ioctl 2 .\" commands are provided for a datagram socket in the .\" .Nm .\" domain; they have the same form as the .\" .Dv SIOCIFADDR .\" command (see .\" .Xr intro 4 ) . .\" .Pp .\" .Bl -tag -width SIOCSIFNETMASK .\" .It Dv SIOCSIFNETMASK .\" Set interface network mask. .\" The network mask defines the network part of the address; .\" if it contains more of the address than the address type would indicate, .\" then subnets are in use. .\" .It Dv SIOCGIFNETMASK .\" Get interface network mask. .\" .El .\" .Sh ROUTING .\" The current implementation of Internet protocols includes some routing-table .\" adaptations to provide enhanced caching of certain end-to-end .\" information necessary for Transaction TCP and Path MTU Discovery. The .\" following changes are the most significant: .\" .Bl -enum .\" .It .\" All IP routes, except those with the .\" .Dv RTF_CLONING .\" flag and those to multicast destinations, have the .\" .Dv RTF_PRCLONING .\" flag forcibly enabled (they are thus said to be .\" .Dq "protocol cloning" ). .\" .It .\" When the last reference to an IP route is dropped, the route is .\" examined to determine if it was created by cloning such a route. If .\" this is the case, the .\" .Dv RTF_PROTO3 .\" flag is turned on, and the expiration timer is initialized to go off .\" in net.inet.ip.rtexpire seconds. If such a route is re-referenced, .\" the flag and expiration timer are reset. .\" .It .\" A kernel timeout runs once every ten minutes, or sooner if there are .\" soon-to-expire routes in the kernel routing table, and deletes the .\" expired routes. .\" .El .\" .Pp .\" A dynamic process is in place to modify the value of .\" net.inet.ip.rtexpire if the number of cached routes grows too large. .\" If after an expiration run there are still more than .\" net.inet.ip.rtmaxcache unreferenced routes remaining, the rtexpire .\" value is multiplied by 3/4, and any routes which have longer .\" expiration times have those times adjusted. This process is damped .\" somewhat by specification of a minimum rtexpire value .\" (net.inet.ip.rtminexpire), and by restricting the reduction to once in .\" a ten-minute period. .\" .Pp .\" If some external process deletes the original route from which a .\" protocol-cloned route was generated, the ``child route'' is deleted. .\" (This is actually a generic mechanism in the routing code support for .\" protocol-requested cloning.) .\" .Pp .\" No attempt is made to manage routes which were not created by protocol .\" cloning; these are assumed to be static, under the management of an .\" external routing process, or under the management of a link layer .\" (e.g., .\" .Tn ARP .\" for Ethernets). .\" .Pp .\" Only certain types of network activity will result in the cloning of a .\" route using this mechanism. Specifically, those protocols (such as .\" .Tn TCP .\" and .\" .Tn UDP ) .\" which themselves cache a long-lasting reference to route for a destination .\" will trigger the mechanism; whereas raw .\" .Tn IP .\" packets, whether locally-generated or forwarded, will not. .Ss MIB Variables A number of variables are implemented in the net.inet6 branch of the .Xr sysctl 3 MIB. In addition to the variables supported by the transport protocols (for which the respective manual pages may be consulted), the following general variables are defined: .Bl -tag -width IPV6CTL_MAXFRAGPACKETS .It Dv IPV6CTL_FORWARDING .Pq ip6.forwarding Boolean: enable/disable forwarding of .Tn IPv6 packets. Also, identify if the node is acting as a router. Defaults to off. .It Dv IPV6CTL_SENDREDIRECTS .Pq ip6.redirect Boolean: enable/disable sending of .Tn ICMPv6 redirects in response to unforwardable .Tn IPv6 packets. This option is ignored unless the node is routing .Tn IPv6 packets, and should normally be enabled on all systems. Defaults to on. .It Dv IPV6CTL_DEFHLIM .Pq ip6.hlim Integer: default hop limit value to use for outgoing .Tn IPv6 packets. This value applies to all the transport protocols on top of .Tn IPv6 . There are APIs to override the value. .It Dv IPV6CTL_MAXFRAGPACKETS .Pq ip6.maxfragpackets Integer: default maximum number of fragmented packets the node will accept. 0 means that the node will not accept any fragmented packets. -1 means that the node will accept as many fragmented packets as it receives. The flag is provided basically for avoiding possible DoS attacks. .It Dv IPV6CTL_ACCEPT_RTADV .Pq ip6.accept_rtadv Boolean: enable/disable receiving of .Tn ICMPv6 router advertisement packets, and autoconfiguration of address prefixes and default routers. The node must be a host .Pq not a router for the option to be meaningful. Defaults to off. .It Dv IPV6CTL_KEEPFAITH .Pq ip6.keepfaith Boolean: enable/disable .Dq FAITH TCP relay IPv6-to-IPv4 translator code in the kernel. Refer .Xr faith 4 and .Xr faithd 8 for detail. Defaults to off. .It Dv IPV6CTL_LOG_INTERVAL .Pq ip6.log_interval Integer: default interval between .Tn IPv6 packet forwarding engine log output .Pq in seconds . .It Dv IPV6CTL_HDRNESTLIMIT .Pq ip6.hdrnestlimit Integer: default number of the maximum .Tn IPv6 extension headers permitted on incoming .Tn IPv6 packets. If set to 0, the node will accept as many extension headers as possible. .It Dv IPV6CTL_DAD_COUNT .Pq ip6.dad_count Integer: default number of .Tn IPv6 DAD .Pq duplicated address detection probe packets. The packets will be generated when .Tn IPv6 interface addresses are configured. .It Dv IPV6CTL_AUTO_FLOWLABEL .Pq ip6.auto_flowlabel Boolean: enable/disable automatic filling of .Tn IPv6 flowlabel field, for outstanding connected transport protocol packets. The field might be used by intermediate routers to identify packet flows. Defaults to on. .It Dv IPV6CTL_DEFMCASTHLIM .Pq ip6.defmcasthlim Integer: default hop limit value for an .Tn IPv6 multicast packet sourced by the node. This value applies to all the transport protocols on top of .Tn IPv6 . There are APIs to override the value as documented in .Xr ip6 4 . .It Dv IPV6CTL_GIF_HLIM .Pq ip6.gifhlim Integer: default maximum hop limit value for an .Tn IPv6 packet generated by .Xr gif 4 tunnel interface. .It Dv IPV6CTL_KAME_VERSION .Pq ip6.kame_version String: identifies the version of KAME .Tn IPv6 stack implemented in the kernel. .It Dv IPV6CTL_USE_DEPRECATED .Pq ip6.use_deprecated Boolean: enable/disable use of deprecated address, specified in RFC2462 5.5.4. Defaults to on. .It Dv IPV6CTL_RR_PRUNE .Pq ip6.rr_prune Integer: default interval between .Tn IPv6 router renumbering prefix babysitting, in seconds. .It Dv IPV6CTL_MAPPED_ADDR .Pq ip6.mapped_addr Boolean: enable/disable use of .Tn IPv4 mapped address on .Dv AF_INET6 sockets. Defaults to on. .El .Sh SEE ALSO .Xr ioctl 2 , .Xr socket 2 , .Xr sysctl 3 , .Xr icmp6 4 , .Xr intro 4 , .Xr ip6 4 , .Xr tcp 4 , .Xr ttcp 4 , .Xr udp 4 .Sh CAVEAT The IPv6 support is subject to change as the Internet protocols develop. Users should not depend on details of the current implementation, but rather the services exported. .Pp Users are suggested to implement .Dq version independent code as much as possible, as you will need to support both .Xr inet 4 and .Nm inet6 . .Sh STANDARDS .Rs .%A Tatsuya Jinmei .%A Atsushi Onoe .%T "An Extension of Format for IPv6 Scoped Addresses" .%R internet draft .%N draft-ietf-ipngwg-scopedaddr-format-00.txt .%O work in progress material .Re .Sh HISTORY The .Nm IPv6 APIs are defined in RFC2553 and RFC2292. The implementation described herein appeared in WIDE/KAME project.