#!/stand/sh # # netinst.sh - configure the user's network. # # Written: November 11th, 1994 # Copyright (C) 1994 by Jordan K. Hubbard # # Permission to copy or use this software for any purpose is granted # provided that this message stay intact, and at this location (e.g. no # putting your name on top after doing something trivial like reindenting # it, just to make it look like you wrote it!). # # $Id: netinst.sh,v 1.8 1995/04/08 09:43:54 phk Exp $ if [ "${_NETINST_SH_LOADED_}" = "yes" ]; then return 0 else _NETINST_SH_LOADED_=yes fi # Grab the miscellaneous functions. . /stand/scripts/miscfuncs.sh network_set_defaults() { HOSTNAME="" DOMAIN="" NETMASK="0xffffff00" IPADDR="127.0.0.1" IFCONFIG_FLAGS="" REMOTE_HOSTIP="" REMOTE_IPADDR="" INTERFACE="" SERIAL_INTERFACE="/dev/cuaa0" SERIAL_SPEED="38400" } network_basic_setup() { HOSTNAME="" while [ "${HOSTNAME}" = "" ]; do DEFAULT_VALUE="" if ! network_dialog "What is the fully qualified name of this host?"; then return 1; fi if [ "${ANSWER}" = "" ]; then error "You must select a host name!" continue else HOSTNAME=${ANSWER} fi done sed -e "s/hostname=.\*\$/hostname=${HOSTNAME}/" < /etc/sysconfig \ > /etc/sysconfig.new && mv /etc/sysconfig.new /etc/sysconfig ${HOSTNAME_CMD} ${HOSTNAME} DEFAULT_VALUE=`echo ${HOSTNAME} | sed -e 's/[^.]*\.//'` if network_dialog "What is the domain name of this host (Internet, not YP/NIS)?"; then DOMAIN=${ANSWER} fi DEFAULT_VALUE=${IPADDR} if ! network_dialog "What is the IP address of this host?"; then return 1; fi IPADDR=${ANSWER} echo "${IPADDR} ${HOSTNAME} `echo ${HOSTNAME} | sed -e 's/\.${DOMAIN}//'`" >> ${ETC}/hosts } network_setup_ether() { dialog --title "Ethernet Interface Name" --menu \ "Please select the type of ethernet interface you have:\n" -1 -1 11 \ "ed0" "WD80x3, SMC, Novell NE[21]000 or 3C503 generic NIC" \ "ed1" "Same as above, but at a different address" \ "eg0" "3Com 3c505 (Etherlink/+)" \ "ep0" "3COM 3C509" \ "de0" "DEC PCI ethernet adapter (or compatible)" \ "ie0" "AT&T StarLan and EN100 family" \ "is0" "Isolan 4141-0 or Isolink 4110" \ "ix0" "Intel EtherExpress" \ "le0" "DEC Etherworks ethernet adapter" \ "lnc0" "Ether 32V board (VL ethernet card)" \ "ze0" "PCMCIA IBM or National card" \ "zp0" "3Com 3c589 PCMCIA card" \ 2> ${TMP}/menu.tmp.$$ RETVAL=$? INTERFACE=`cat ${TMP}/menu.tmp.$$` rm -f ${TMP}/menu.tmp.$$ if ! handle_rval ${RETVAL}; then return 1; fi } network_setup_remote() { DEFAULT_VALUE="${REMOTE_IPADDR}" if ! network_dialog "What is the IP number for the remote host?"; then return 1 fi REMOTE_IPADDR=${ANSWER} } network_setup_serial() { network_setup_remote INTERFACE=$1 DEFAULT_VALUE=${SERIAL_INTERFACE} if ! network_dialog "What serial port do you wish to use?"; then return 1 fi SERIAL_INTERFACE=${ANSWER} DEFAULT_VALUE=${SERIAL_SPEED} if ! network_dialog "What speed is the serial connection?"; then return 1 fi SERIAL_SPEED=${ANSWER} if dialog --title "Dial" --yesno \ "Do you need to dial the phone or otherwise talk to the modem?" \ -1 -1; then confirm \ "You may now dialog with your modem and set up the connection. Be sure to disable DTR sensitivity (usually with AT&D0) or the modem may hang up when you exit 'cu'. Use ~. to exit cu and continue." dialog --clear # Grottyness to deal with a weird crunch bug. if [ ! -f /stand/cu ]; then ln /stand/tip /stand/cu; fi /stand/cu -l ${SERIAL_INTERFACE} -s ${SERIAL_SPEED} dialog --clear fi } network_setup_plip() { network_setup_remote INTERFACE=lp0 } network_setup() { DONE=0 while [ "${INTERFACE}" = "" ]; do dialog --title "Set up network interface" --menu \ "Please select the type of network connection you have:\n" \ -1 -1 3 \ "Ether" "A supported ethernet card" \ "SLIP" "A point-to-point SLIP (Serial Line IP) connection" \ "PLIP" "A Parallel-Line IP setup (with standard laplink cable)" \ 2> ${TMP}/menu.tmp.$$ RETVAL=$? CHOICE=`cat ${TMP}/menu.tmp.$$` rm -f ${TMP}/menu.tmp.$$ if ! handle_rval ${RETVAL}; then return 1; fi case ${CHOICE} in Ether) if ! network_setup_ether; then continue; fi ;; SLIP) if ! network_setup_serial sl0; then continue; fi ;; PLIP) if ! network_setup_plip; then continue; fi ;; esac if [ "${INTERFACE}" = "" ]; then continue; fi network_basic_setup DEFAULT_VALUE="${NETMASK}" if network_dialog "Please specify the netmask"; then if [ "${ANSWER}" != "" ]; then NETMASK=${ANSWER} fi fi DEFAULT_VALUE="" if network_dialog "Any extra flags to ${IFCONFIG_CMD}, put them here"; then IFCONFIG_FLAGS=${ANSWER} fi echo "Progress <${IFCONFIG_CMD} ${INTERFACE} ${IPADDR} ${REMOTE_IPADDR} netmask ${NETMASK} ${IFCONFIG_FLAGS}>" >/dev/ttyv1 if ! ${IFCONFIG_CMD} ${INTERFACE} ${IPADDR} ${REMOTE_IPADDR} netmask ${NETMASK} ${IFCONFIG_FLAGS} > /dev/ttyv1 2>&1 ; then error "Unable to configure interface ${INTERFACE}" IPADDR="" INTERFACE="" continue fi if [ "${INTERFACE}" = "sl0" ]; then DEFAULT_VALUE=${SLATTACH_FLAGS} if network_dialog "Set extra flags to ${SLATTACH_CMD}?"; then SLATTACH_FLAGS=${ANSWER} fi ${SLATTACH_CMD} ${SLATTACH_FLAGS} ${SERIAL_SPEED} ${SERIAL_INTERFACE} progress ${SLATTACH_CMD} ${SLATTACH_FLAGS} ${SERIAL_SPEED} ${SERIAL_INTERFACE} fi echo "${IPADDR} ${REMOTE_IPADDR} netmask ${NETMASK} ${IFCONFIG_FLAGS}" > ${ETC}/hostname.${INTERFACE} DEFAULT_VALUE="" if network_dialog "If you have a default gateway, enter its IP address"; then if [ "${ANSWER}" != "" ]; then GATEWAY=${ANSWER} ${ROUTE_CMD} ${ROUTE_FLAGS} ${GATEWAY} > /dev/ttyv1 2>&1 progress ${ROUTE_CMD} ${ROUTE_FLAGS} ${GATEWAY} echo ${GATEWAY} > ${ETC}/defaultrouter fi fi DEFAULT_VALUE="" if network_dialog "If you have a name server, enter its IP address"; then if [ "${ANSWER}" != "" ]; then NAMESERVER=${ANSWER} echo "domain ${DOMAIN}" > ${ETC}/resolv.conf echo "nameserver ${NAMESERVER}" >> ${ETC}/resolv.conf fi fi done return 0 }