summaryrefslogtreecommitdiffstats
path: root/sys/pci/if_ste.c
Commit message (Collapse)AuthorAgeFilesLines
* Make all Ethernet drivers attach using ether_ifattach() and detach usingarchie2000-07-131-7/+3
| | | | | | | | | ether_ifdetach(). The former consolidates the operations of if_attach(), ng_ether_attach(), and bpfattach(). The latter consolidates the corresponding detach operations. Reviewed by: julian, freebsd-net
* Use the correct register name. s/PCI_COMMAND_STATUS_REG/PCIR_COMMAND/peter2000-05-281-3/+3
|
* Move code to handle BPF and bridging for incoming Ethernet packets outarchie2000-05-141-37/+0
| | | | | | | | | | | | | | | of the individual drivers and into the common routine ether_input(). Also, remove the (incomplete) hack for matching ethernet headers in the ip_fw code. The good news: net result of 1016 lines removed, and this should make bridging now work with *all* Ethernet drivers. The bad news: it's nearly impossible to test every driver, especially for bridging, and I was unable to get much testing help on the mailing lists. Reviewed by: freebsd-net
* Depend on miibus.peter2000-04-291-0/+2
| | | | | | | | Note that if_aue doesn't strictly depend on usb because it uses the method interface for calls rather than using internal symbols, and because it's a child driver of usb and therefore will not try and do anything unless the parent usb code is loaded at some point. if_aue does strictly depend on miibus as it will fail to link if it is missing.
* Spruce up the Sundance ST201 driver:wpaul1999-12-071-130/+112
| | | | | | | | | | | | - Convert to using TX descritor polling similar to the xl driver (the ST201 is a clone of the 3c90xB chipset and offers the same transmit polling scheme). This should reduce TX overhad a little. - Make sure to reset PHY when switching mode, as in the starfire driver. - Fix instances of free() that should be contigfree(). - Remove dead code.
* As suggested by phk, unconditionalize BPF support in these drivers. Sincewpaul1999-09-231-13/+0
| | | | | | | there are stubs compiled into the kernel if BPF support is not enabled, there aren't any problems with unresolved symbols. The modules in /modules are compiled with BPF support enabled anyway, so the most this will do is bloat GENERIC a little.
* Tweak these for what I hope is the last time: change the DRIVER_MODULE()wpaul1999-09-221-1/+1
| | | | | | | | | | declaration for the interface driver from "foo" to "if_foo" but leave the declaration for the miibus attached to the interface driver alone. This lets the internal module name be "if_foo" while still allowing the miibus instances to attach to "foo." This should allow ifconfig to autoload driver modules again without breaking the miibus attach.
* Un-do the changes to the DRIVER_MODULE() declarations in these drivers.wpaul1999-09-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This whole idea isn't going to work until somebody makes the bus/kld code smarter. The idea here is to change the module's internal name from "foo" to "if_foo" so that ifconfig can tell a network driver from a non-network one. However doing this doesn't work correctly no matter how you slice it. For everything to work, you have to change the name in both the driver_t struct and the DRIVER_MODULE() declaration. The problems are: - If you change the name in both places, then the kernel thinks that the device's name is now "if_foo", so you get things like: if_foo0: <FOO ethernet> irq foo at device foo on pcifoo if_foo0: Ethernet address: foo:foo:foo:foo:foo:foo This is bogus. Now the device name doesn't agree with the logical interface name. There's no reason for this, and it violates the principle of least astonishment. - If you leave the name in the driver_t struct as "foo" and only change the names in the DRIVER_MODULE() declaration to "if_foo" then attaching drivers to child devices doesn't work because the names don't agree. This breaks miibus: drivers that need to have miibuses and PHY drivers attached never get them. In other words: damned if you do, damned if you don't. This needs to be thought through some more. Since the drivers that use miibus are broken, I have to change these all back in order to make them work again. Yes this will stop ifconfig from being able to demand load driver modules. On the whole, I'd rather have that than having the drivers not work at all.
* Grrr. Okay, changing the devnames was a bad idea. Put them back the waywpaul1999-09-201-1/+1
| | | | they were.
* Fix the strings in the driver_t structs so that they match the new nameswpaul1999-09-201-1/+1
| | | | in the DRIVER_MODULES() declarations. *sigh*
* Goofed and didn't change the second DRIVER_MODULE() linking these withobrien1999-09-201-1/+1
| | | | | | the miibus. Noticed by: wpaul
* Change the name we register with DRIVER_MODULE() to include the leadingobrien1999-09-201-1/+1
| | | | | | "if_". Reviewed by: msmith, wpaul
* Add a pointer to "controller miibus0" for people who will not read thepeter1999-09-081-0/+1
| | | | | commit messages or GENERIC and insist on running -CURRENT. It probably won't work, but it's worth a try.
* Make sure to free resources on failure correctly in a couple of placeswpaul1999-08-311-2/+8
| | | | in ste_attach().
* Don't restrict our requests for contiguous memory to addresses >= 1MB.bde1999-08-291-1/+1
| | | | | | | | This fixes, at least, panics in ncr_attach() on i386's with about 5MB of memory. The restriction was a hack to leave some low memory for ISA DMA, but on i386's we now allocate pages from the top down, so all the restriction did was cause our allocations to fail when there is no free memory above 1MB.
* $Id$ -> $FreeBSD$peter1999-08-281-2/+2
|
* Properly re-enable the transmitter in the TX error handler.wpaul1999-08-261-5/+3
|
* This commit adds device driver support for the Sundance Technologies ST201wpaul1999-08-211-0/+1644
PCI fast ethernet controller. Currently, the only card I know that uses this chip is the D-Link DFE-550TX. (Don't ask me where to buy these: the only cards I have are samples sent to me by D-Link.) This driver is the first to make use of the miibus code once I'm sure it all works together nicely, I'll start converting the other drivers. The Sundance chip is a clone of the 3Com 3c90x Etherlink XL design only with its own register layout. Support is provided for ifmedia, hardware multicast filtering, bridging and promiscuous mode.
OpenPOWER on IntegriCloud