summaryrefslogtreecommitdiffstats
path: root/sys/dev/vr
Commit message (Collapse)AuthorAgeFilesLines
* Announce flow control capability to PHY drivers and enable flowyongari2011-11-282-11/+43
| | | | | | | | | | control for all vr(4) controllers that support it. It's known that old vr(4) controllers(Rhine II) does not support TX pause but Rhine III supports both TX and RX pause. Make TX pause really work on Rhine III by letting controller know available RX buffers. While here, adjust XON/XOFF parameters to get better performance with flow control.
* Reuse flag variable to represent driver internal states rather thanyongari2011-11-282-19/+19
| | | | | | | using member variables in softc. While I'm here change media after setting IFF_DRV_RUNNING. This will remove unnecessary link state handling in vr_tick() if controller established a link immediately.
* - There's no need to overwrite the default device method with the defaultmarius2011-11-221-5/+1
| | | | | | | | | | one. Interestingly, these are actually the default for quite some time (bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9) since r52045) but even recently added device drivers do this unnecessarily. Discussed with: jhb, marcel - While at it, use DEVMETHOD_END. Discussed with: jhb - Also while at it, use __FBSDID.
* Close a race where SIOCGIFMEDIA ioctl get inconsistent link status.yongari2011-10-171-1/+1
| | | | | | | | Because driver is accessing a common MII structure in mii_pollstat(), updating user supplied structure should be done before dropping a driver lock. Reported by: Karim (fodillemlinkarimi <> gmail dot com)
* Sprinkle const.marius2011-10-091-9/+9
|
* Remove link state change callback handler. There is no need toyongari2011-06-222-28/+20
| | | | | | | | | | | | | | register both status change and link state change callbacks. Implement checking valid link in state change callback and poll active link state in vr_tick(). This allows immediate detection of lost link as well as protecting driver from frequent link flips during link renegotiation. taskq implementation was removed because driver now needs to poll link state in vr_tick(). While I'm here do not report current link state if interface is not running. Tested by: n_hibma MFC after: 1 week
* - Remove attempts to implement setting of BMCR_LOOP/MIIF_NOLOOPmarius2011-05-031-4/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | (reporting IFM_LOOP based on BMCR_LOOP is left in place though as it might provide useful for debugging). For most mii(4) drivers it was unclear whether the PHYs driven by them actually support loopback or not. Moreover, typically loopback mode also needs to be activated on the MAC, which none of the Ethernet drivers using mii(4) implements. Given that loopback media has no real use (and obviously hardly had a chance to actually work) besides for driver development (which just loopback mode should be sufficient for though, i.e one doesn't necessary need support for loopback media) support for it is just dropped as both NetBSD and OpenBSD already did quite some time ago. - Let mii_phy_add_media() also announce the support of IFM_NONE. - Restructure the PHY entry points to use a structure of entry points instead of discrete function pointers, and extend this to include a "reset" entry point. Make sure any PHY-specific reset routine is always used, and provide one for lxtphy(4) which disables MII interrupts (as is done for a few other PHYs we have drivers for). This includes changing NIC drivers which previously just called the generic mii_phy_reset() to now actually call the PHY-specific reset routine, which might be crucial in some cases. While at it, the redundant checks in these NIC drivers for mii->mii_instance not being zero before calling the reset routines were removed because as soon as one PHY driver attaches mii->mii_instance is incremented and we hardly can end up in their media change callbacks etc if no PHY driver has attached as mii_attach() would have failed in that case and not attach a miibus(4) instance. Consequently, NIC drivers now no longer should call mii_phy_reset() directly, so it was removed from EXPORT_SYMS. - Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe(). The purpose of that function is to perform the common steps to attach a PHY driver instance and to hook it up to the miibus(4) instance and to optionally also handle the probing, addition and initialization of the supported media. So all a PHY driver without any special requirements has to do in its bus attach method is to call mii_phy_dev_attach() along with PHY-specific MIIF_* flags, a pointer to its PHY functions and the add_media set to one. All PHY drivers were updated to take advantage of mii_phy_dev_attach() as appropriate. Along with these changes the capability mask was added to the mii_softc structure so PHY drivers taking advantage of mii_phy_dev_attach() but still handling media on their own do not need to fiddle with the MII attach arguments anyway. - Keep track of the PHY offset in the mii_softc structure. This is done for compatibility with NetBSD/OpenBSD. - Keep track of the PHY's OUI, model and revision in the mii_softc structure. Several PHY drivers require this information also after attaching and previously had to wrap their own softc around mii_softc. NetBSD/OpenBSD also keep track of the model and revision on their mii_softc structure. All PHY drivers were updated to take advantage as appropriate. - Convert the mebers of the MII data structure to unsigned where appropriate. This is partly inspired by NetBSD/OpenBSD. - According to IEEE 802.3-2002 the bits actually have to be reversed when mapping an OUI to the MII ID registers. All PHY drivers and miidevs where changed as necessary. Actually this now again allows to largely share miidevs with NetBSD, which fixed this problem already 9 years ago. Consequently miidevs was synced as far as possible. - Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that weren't explicitly converted to support flow control before. It's unclear whether flow control actually works with these but typically it should and their net behavior should be more correct with these changes in place than without if the MAC driver sets MIIF_DOPAUSE. Obtained from: NetBSD (partially) Reviewed by: yongari (earlier version), silence on arch@ and net@
* Do a sweep of the tree replacing calls to pci_find_extcap() with calls tojhb2011-03-231-3/+3
| | | | pci_find_cap() instead.
* Convert the PHY drivers to honor the mii_flags passed down and convertmarius2010-10-152-15/+8
| | | | | | | | | | | | | | | | | | | | | | | the NIC drivers as well as the PHY drivers to take advantage of the mii_attach() introduced in r213878 to get rid of certain hacks. For the most part these were: - Artificially limiting miibus_{read,write}reg methods to certain PHY addresses; we now let mii_attach() only probe the PHY at the desired address(es) instead. - PHY drivers setting MIIF_* flags based on the NIC driver they hang off from, partly even based on grabbing and using the softc of the parent; we now pass these flags down from the NIC to the PHY drivers via mii_attach(). This got us rid of all such hacks except those of brgphy() in combination with bce(4) and bge(4), which is way beyond what can be expressed with simple flags. While at it, I took the opportunity to change the NIC drivers to pass up the error returned by mii_attach() (previously by mii_phy_probe()) and unify the error message used in this case where and as appropriate as mii_attach() actually can fail for a number of reasons, not just because of no PHY(s) being present at the expected address(es). Reviewed by: jhb, yongari
* vr_init_locked() will stop and reset the controller. Removeyongari2010-08-241-4/+0
| | | | unnecessary vr_stop()/vr_reset() calls.
* Remove unnecessary controller reinitialization.yongari2010-08-241-0/+6
| | | | | | | CAM filter handling was rewritten long time ago so it should not require controller reinitialization. PR: kern/87506
* Use if_maddr_rlock()/if_maddr_runlock() rather than IF_ADDR_LOCK()/rwatson2009-06-261-2/+2
| | | | | | | | | | | | | IF_ADDR_UNLOCK() across network device drivers when accessing the per-interface multicast address list, if_multiaddrs. This will allow us to change the locking strategy without affecting our driver programming interface or binary interface. For two wireless drivers, remove unnecessary locking, since they don't actually access the multicast address list. Approved by: re (kib) MFC after: 6 weeks
* When user_frac in the polling subsystem is low it is going to busy theattilio2009-05-301-9/+17
| | | | | | | | | | | | | | | | | | | | | CPU for too long period than necessary. Additively, interfaces are kept polled (in the tick) even if no more packets are available. In order to avoid such situations a new generic mechanism can be implemented in proactive way, keeping track of the time spent on any packet and fragmenting the time for any tick, stopping the processing as soon as possible. In order to implement such mechanism, the polling handler needs to change, returning the number of packets processed. While the intended logic is not part of this patch, the polling KPI is broken by this commit, adding an int return value and the new flag IFCAP_POLLING_NOCOUNT (which will signal that the return value is meaningless for the installed handler and checking should be skipped). Bump __FreeBSD_version in order to signal such situation. Reviewed by: emaste Sponsored by: Sandvine Incorporated
* It seems there are still issues on multicast perfect filtering.yongari2008-12-121-1/+1
| | | | | | | Disable it until I find spare time to analyze the issue. Reported by: Goran Lowkrantz <glz <> hidden-powers DOT com> MFC after: 3 days
* Fix typo. It restuled in activating unwanted Rx filtering as wellyongari2008-11-171-1/+2
| | | | | | as resetting Rx threshold configuration. Submitted by: Joost Mulders < Joost.Mulders <> Sun DOT COM >
* Fix a multicast handling regression on VT6105M introduced inyongari2008-07-162-25/+60
| | | | | | | | | | | | | | | | | | | | | | | vr(4) overhauling(r177050). It seems that filtering multicast addresses with multicast CAM entries require accessing 'CAM enable bit' for each CAM entry. Subsequent accessing multicast CAM control register without toggling the 'CAM enable bit' seem to no effects. In order to fix that separate CAM setup from CAM mask configuration and CAM entry modification. While I'm here add VLAN CAM filtering feature which will be enabled in future(FreeBSD now can receive VLAN id insertion/removal event from vlan(4) on the fly). For VT6105M hardware, explicitly disable VLAN hardware tag insertion/stripping and enable VLAN CAM filtering for VLAN id 0. This shall make non-VLAN frames set VR_RXSTAT_VIDHIT bit in Rx status word. Added multicast/VLAN CAM address definition to header file. PR: kern/125010, kern/125024 MFC after: 1 week
* Fix VR_RXSTAT_RX_OK bit definition which lasted for more than 9yongari2008-07-162-3/+4
| | | | | | | | | | | | | years. All datasheet I have indicates the bit 15 is the VR_RXSTAT_RX_OK. The bit 14 is reserved for all Rhine family except VT6105M. VT6105M uses that bit to indicate a VLAN frame with matching CAM VLAN id. Use the VR_RXSTAT_RX_OK instead of VR_RXSTAT_RXERR when vr(4) checks the validity of received frame. This should fix occasional dropping frames on VT6105M. Tested by: Goran Lowkrantz ( goran.lowkrantz at ismobile dot com ) MFC after: 1 week
* Teach vr(4) to use bus_dma(9) and major overhauling to handle linkyongari2008-03-112-789/+2006
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | state change and reliable error recovery. o Moved vr_softc structure and relevant macros to header file. o Use PCIR_BAR macro to get BARs. o Implemented suspend/resume methods. o Implemented automatic Tx threshold configuration which will be activated when it suffers from Tx underrun. Also Tx underrun will try to restart only Tx path and resort to previous full-reset(both Rx/Tx) operation if restarting Tx path have failed. o Removed old bit-banging MII interface. Rhine provides simple and efficient MII interface. While I'm here show PHY address and PHY register number when its read/write operation was failed. o Define VR_MII_TIMEOUT constant and use it in MII access routines. o Always honor link up/down state reported by mii layers. The link state information is used in vr_start() to determine whether we got a valid link. o Removed vr_setcfg() which is now handled in vr_link_task(), link state taskqueue handler. When mii layer reports link state changes the taskqueue handler reprograms MAC to reflect negotiated duplex settings. Flow-control changes are not handled yet and it should be revisited when mii layer knows the notion of flow-control. o Added a new sysctl interface to get statistics of an instance of the driver.(sysctl dev.vr.0.stats=1) o Chip name was renamed to reflect the official name of the chips described in VIA Rhine I/II/III datasheet. REV_ID_3065_A -> REV_ID_VT6102_A REV_ID_3065_B -> REV_ID_VT6102_B REV_ID_3065_C -> REV_ID_VT6102_C REV_ID_3106_J -> REV_ID_VT6105_A0 REV_ID_3106_S -> REV_ID_VT6105M_A0 The following chip revisions were added. #define REV_ID_VT6105_B0 0x83 #define REV_ID_VT6105_LOM 0x8A #define REV_ID_VT6107_A0 0x8C #define REV_ID_VT6107_A1 0x8D #define REV_ID_VT6105M_B1 0x94 o Always show chip revision number in device attach. This shall help identifying revision specific issues. o Check whether EEPROM reloading is complete by inspecting the state of VR_EECSR_LOAD bit. This bit is self-cleared after the EEPROM reloading. Previously vr(4) blindly spins for 200us which may/may not enough to complete the EEPROM reload. o Removed if_mtu setup. It's done in ether_ifattach(). o Use our own callout to drive watchdog timer. o In vr_attach disable further interrupts after reset. For VT6102 or newer hardwares, diable MII state change interrupt as well because mii state handling is done by mii layer. o Add more sane register initialization for VT6102 or newer chips. - Have NIC report error instead of retrying forever. - Let hardware detect MII coding error. - Enable MODE10T mode. - Enable memory-read-multiple for VT6107. o PHY address for VT6105 or newer chips is located at fixed address 1. For older chips the PHY address is stored in VR_PHYADDR register. Armed with these information, there is no need to re-read VR_PHYADDR register in miibus handler to get PHY address. This saves one register access cycle for each MII access. o Don't reprogram VR_PHYADDR register whenever access to a register located at a PHY address is made. Rhine fmaily allows reprogramming PHY address location via VR_PHYADDR register depending on VR_MIISTAT_PHYOPT bit of VR_MIISTAT register. This used to lead numerous phantom PHYs attached to miibus during phy probe phase and driver used to limit allowable PHY address in mii register accessors for certain chip revisions. This removes one more register access cycle for each MII access. o Correctly set VLAN header length. o bus_dma(9) conversion. - Limit DMA access to be in range of 32bit address space. Hardware doesn't support DAC. - Apply descriptor ring alignment requirements(16 bytes alignment) - Apply Rx buffer address alignment requirements(4 bytes alignment) - Apply Tx buffer address alignment requirements(4 bytes alignment) for Rhine I chip. Rhine II or III has no Tx buffer address alignment restrictions, though. - Reduce number of allowable number of DMA segments to 8. - Removed the atomic(9) used in descriptor ownership managements as it's job of bus_dmamap_sync(9). With these change vr(4) should work on all platforms. o Rhine uses two separated 8bits command registers to control Tx/Rx MAC. So don't access it as a single 16bit register. o For non-strict alignment architectures vr(4) no longer require time-consuming copy operation for received frames to align IP header. This greatly improves Rx performance on i386/amd64 platforms. However the alignment is still necessary for strict-alignment platforms(e.g. sparc64). The alignment is handled in new fuction vr_fixup_rx(). o vr_rxeof() now rejects multiple-segmented(fragmented) frames as vr(4) is not ready to handle this situation. Datasheet said nothing about the reason when/why it happens. o In vr_newbuf() don't set VR_RXSTAT_FIRSTFRAG/VR_RXSTAT_LASTFRAG bits as it's set by hardware. o Don't pass checksum offload information to upper layer for fragmented frames. The hardware assisted checksum is valid only when the frame is non-fragmented IP frames. Also mark the checksum is valid for corrupted frames such that upper layers doesn't need to recompute the checksum with software routine. o Removed vr_rxeoc(). RxDMA doesn't seem to need to be idle before sending VR_CMD_RX_GO command. Previously it used to stop RxDMA first which in turn resulted in long delays in Rx error recovery. o Rewrote Tx completion handler. - Always check VR_TXSTAT_OWN bit in status word prior to inspecting other status bits in the status word. - Collision counter updates were corrected as VT3071 or newer ones use different bits to notify collisions. - Unlike other chip revisions, VT86C100A uses different bit to indicate Tx underrun. For VT3071 or newer ones, check both VR_TXSTAT_TBUFF and VR_TXSTAT_UDF bits to see whether Tx underrun was happend. In case of Tx underrun requeue the failed frame and restart stalled Tx SM. Also double Tx DMA threshold size on each failure to mitigate future Tx underruns. - Disarm watchdog timer only if we have no queued packets, otherwise don't touch watchdog timer. o Rewrote interrupt handler. - status word in Tx/Rx descriptors indicates more detailed error state required to recover from the specific error. There is no need to rely on interrupt status word to recover from Tx/Rx error except PCI bus error. Other event notifications like statistics counter overflows or link state events will be handled in main interrupt handler. - Don't touch VR_IMR register if we are in suspend mode. Touching the register may hang the hardware if we are in suspended state. Previously it seems that touching VR_IMR register in interrupt handler was to work-around panic occurred in system shutdown stage on SMP systems. I think that work-around would hide root-cause of the panic and I couldn't reproduce the panic with multiple attempts on my box. o While padding space to meet minimum frame size, zero the pad data in order to avoid possibly leaking sensitive data. o Rewrote vr_start_locked(). - Don't try to queue packets if number of available Tx descriptors are short than that of required one. o Don't reinitialize hardware whenever media configuration is changed. Media/link state changes are reported from mii layer if this happens and vr_link_task() will perform necessary changes. o Don't reinitialize hardware if only PROMISC bit was changed. Just toggle the PROMISC bit in hardware is sufficient to reflect the request. o Rearrganed the IFCAP_POLLING/IFCAP_HWCSUM handling in vr_ioctl(). o Generate Tx completion interrupts for every VR_TX_INTR_THRESH-th frames. This reduces Tx completion interrupts under heavy network loads. o Since vr(4) doesn't request Tx interrupts for every queued frames, reclaim any pending descriptors not handled in Tx completion handler before actually firing up watchdog timeouts. o Added vr_tx_stop()/vr_rx_stop() to wait for the end of active TxDMA/RxDMA cycles(draining). These routines are used in vr_stop() to ensure sane state of MAC before releasing allocated Tx/Rx buffers. vr_link_task() also takes advantage of these functions to get to idle state prior to restarting Tx/Rx. o Added vr_tx_start()/vr_rx_start() to restart Rx/Tx. By separating Rx operation from Tx operation vr(4) no longer need to full-reset the hardware in case of Tx/Rx error recovery. o Implemented WOL. o Added VT6105M specific register definitions. VT6105M has the following hardware capabilities. - Tx/Rx IP/TCP/UDP checksum offload. - VLAN hardware tag insertion/extraction. Due to lack of information for getting extracted VLAN tag in Rx path, VLAN hardware support was not implemented yet. - CAM(Content Addressable Memory) based 32 entry perfect multicast/ VLAN filtering. - 8 priority queues. o Implemented CAM based 32 entry perfect multicast filtering for VT6105M. If number of multicast entry is greater than 32, vr(4) uses traditional hash based filtering. o Reflect real Tx/Rx descriptor structure. Previously vr(4) used to embed other driver (private) data into these structure. This type of embedding make it hard to work on LP64 systems. o Removed unused vr_mii_frame structure and MII bit-baning definitions. o Added new PCI configuration registers that controls mii operation and mode selection. o Reduced number of Tx/Rx descriptors to 128 from 256. From my testing, increasing number of descriptors above than 64 didn't help increasing performance at all. Experimentations show 128 Rx descriptors seems to help a lot reducing Rx FIFO overruns under high system loads. It seems the poor Tx performance of Rhine hardwares comes from the limitation of hardware. You wouldn't satuarte the link with vr(4) no matter how fast CPU/large number of descriptors are used. o Added vr_statistics structure to hold various counter values. No regression was reported but one variant of Rhine III(VT6105M) found on RouterBOARD 44 does not work yet(Reported by Milan Obuch). I hope this would be resolved in near future. I'd like to say big thanks to Mike Tancsa who kindly donated a Rhine hardware to me. Without his enthusiastic testing and feedbacks overhauling vr(4) never have been possible. Also thanks to Masayuki Murayama who provided some good comments on the hardware's internals. This driver is result of combined effort of many users who provided many feedbacks so I'd like to say special thanks to them. Hardware donated by: Mike Tancsa (mike AT sentex dot net) Reviewed by: remko (initial version) Tested by: Mike Tancsa(x86), JoaoBR ( joao AT matik DOT com DOT br ) Marcin Wisnicki ( mwisnicki+freebsd AT gmail DOT com ) Stefan Ehmann ( shoesoft AT gmx DOT net ) Florian Smeets ( flo AT kasimir DOT com ) Phil Oleson ( oz AT nixil DOT net ) Larry Baird ( lab AT gta DOT com ) Milan Obuch ( freebsd-current AT dino DOT sk ) remko (initial version)
* Forced commit to note that vr(4) was repocopied from sys/pciyongari2008-03-111-1/+1
| | | | and modified for its new location.
* Fix function prototype for device_shutdown method.yongari2007-11-221-2/+4
|
* Not all VIA Rhine chips support 256 register space. So touchingyongari2007-10-121-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | VR_STICKHW register would result in unexpected results on these hardwares. wpaul said the following for the issue. The vr_attach() routine unconditionally does this for all supported chips: /* * Windows may put the chip in suspend mode when it * shuts down. Be sure to kick it in the head to wake it * up again. */ VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1)); The problem is, the VR_STICKHW register is not valid on all Rhine devices. The VT86C100A chip, which is present on the D-Link DFE-530TX boards, doesn't support power management, and its register space is only 128 bytes wide. The VR_STICKHW register offset falls outside this range. This may go unnoticed in most scenarios, but if you happen to have another PCI device in your system which is assigned the register space immediately after that of the Rhine, the vr(4) driver will incorrectly stomp it. In my case, the BIOS on my test board decided to put the register space for my PRO/100 ethernet board right next to the Rhine, and the Rhine driver ended up clobbering the IMR register of the PRO/100 device. (Long story short: the board kept locking up on boot. Took me the better part of the morning suss out why.) The strictly correct thing to do would be to check the PCI config space to make sure the device supports the power management capability and only write to the VR_STICKHW register if it does. Instead of inspecting chip revision numbers for the availability of VR_STICKHW register, check the existence of power management capability of the hardware as wpaul suggested. Reported by: wpaul Suggested by: wpaul OK'ed by: jhb
* Add VLAN capability.phk2007-04-232-1/+2
| | | | Submitted by: Slawa Olhovchenkov <slw@zxy.spb.ru>
* Remove the old software bit-banging MII interface, we started usingphk2007-04-221-167/+1
| | | | the Rhines shiftregisters in four years ago (1.60).
* Remove further cobwebs: Two layers of pointless substructures.phk2007-04-222-105/+71
|
* Initialize the physical next pointer in the tx descriptors when wephk2007-04-221-7/+8
| | | | initialize instead of in the start routine.
* Don't rename fields with #define.phk2007-04-222-27/+18
| | | | | Collapse two semantically identical structs. Add missing vr_ prefix.
* Run if_vr(4) through FlexeLint and clean some of the cobwebs found.phk2007-04-222-101/+59
|
* Add support for hw-assisted checksums on 6105M.phk2007-04-172-17/+72
| | | | Sponsored by: Soekris Engineering
* No need to throw tag+handle around on the stack.phk2007-04-172-18/+7
|
* Improve the if_vr driver ever so slightly.phk2007-04-172-87/+110
| | | | | | | | | | | | | The 6105M and 6102 does not have the DWORD alignment problem, so don't m_defrag() every packet in the transmit path for those. More stringent usage of tx-descriptor ring and its flags. Tested on 6102 and 6105M, other chips may also be able to run without the m_defrag() but I have neither hardware nor docs to find out. Sponsored by: Soekris Engineering
* o break newbus api: add a new argument of type driver_filter_t topiso2007-02-231-1/+1
| | | | | | | | | | | | | bus_setup_intr() o add an int return code to all fast handlers o retire INTR_FAST/IH_FAST For more info: http://docs.freebsd.org/cgi/getmsg.cgi?fetch=465712+0+current/freebsd-current Reviewed by: many Approved by: re@
* Whitespace nits.ru2006-09-151-1/+1
|
* Consistently use if_printf() only in interface methods: if_start,glebius2006-09-152-9/+12
| | | | | | | | | | if_ioctl, if_watchdog, etc, or in functions that are used by these methods only. In all other cases use device_printf(). This also fixes several panics, when if_printf() is called before softc->ifp was initialized. Submitted by: Alex Lyashkov <umka sevcity.net>
* Remove various bits of conditional Alpha code and fixup a few comments.jhb2006-05-121-6/+0
|
* Do not touch ifp->if_baudrate in miibus aware drivers.glebius2006-02-141-1/+0
|
* - Store pointer to the link-level address right in "struct ifnet"ru2005-11-111-1/+1
| | | | | | | | | | rather than in ifindex_table[]; all (except one) accesses are through ifp anyway. IF_LLADDR() works faster, and all (except one) ifaddr_byindex() users were converted to use ifp->if_addr. - Stop storing a (pointer to) Ethernet address in "struct arpcom", and drop the IFP2ENADDR() macro; all users have been converted to use IF_LLADDR() instead.
* - Use callout_*() to manage the callout and make it MPSAFE.jhb2005-10-312-16/+11
| | | | | | | - Fix locking in detach(), we only need to lock across vr_stop(). Tested by: Mike Tancsa mike at sentex dot net MFC after: 1 week
* - Use if_printf() and device_printf() and remove vr_unit from the softc.jhb2005-10-272-53/+44
| | | | | | I had to initialize the ifnet a bit earlier in attach so that the if_printf()'s in vr_reset() didn't explode with a page fault. - Use M_ZERO with contigmalloc() rather than an explicit bzero.
* Replace FreeBSD 3.x syntax (controller miibus0) with 4.x syntaximp2005-10-221-1/+1
| | | | (device miibus) in time for 7.0 :-)
* In detach method, move if_free() after bus_teardown_intr().ru2005-10-131-2/+3
|
* - Don't pollute opt_global.h with DEVICE_POLLING and introduceglebius2005-10-051-0/+4
| | | | | | | | | opt_device_polling.h - Include opt_device_polling.h into appropriate files. - Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that can be compiled as loadable modules. Reviewed by: bde
* Big polling(4) cleanup.glebius2005-10-011-31/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | o Axe poll in trap. o Axe IFF_POLLING flag from if_flags. o Rework revision 1.21 (Giant removal), in such a way that poll_mtx is not dropped during call to polling handler. This fixes problem with idle polling. o Make registration and deregistration from polling in a functional way, insted of next tick/interrupt. o Obsolete kern.polling.enable. Polling is turned on/off with ifconfig. Detailed kern_poll.c changes: - Remove polling handler flags, introduced in 1.21. The are not needed now. - Forget and do not check if_flags, if_capenable and if_drv_flags. - Call all registered polling handlers unconditionally. - Do not drop poll_mtx, when entering polling handlers. - In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx. - In netisr_poll() axe the block, where polling code asks drivers to unregister. - In netisr_poll() and ether_poll() do polling always, if any handlers are present. - In ether_poll_[de]register() remove a lot of error hiding code. Assert that arguments are correct, instead. - In ether_poll_[de]register() use standard return values in case of error or success. - Introduce poll_switch() that is a sysctl handler for kern.polling.enable. poll_switch() goes through interface list and enabled/disables polling. A message that kern.polling.enable is deprecated is printed. Detailed driver changes: - On attach driver announces IFCAP_POLLING in if_capabilities, but not in if_capenable. - On detach driver calls ether_poll_deregister() if polling is enabled. - In polling handler driver obtains its lock and checks IFF_DRV_RUNNING flag. If there is no, then unlocks and returns. - In ioctl handler driver checks for IFCAP_POLLING flag requested to be set or cleared. Driver first calls ether_poll_[de]register(), then obtains driver lock and [dis/en]ables interrupts. - In interrupt handler driver checks IFCAP_POLLING flag in if_capenable. If present, then returns.This is important to protect from spurious interrupts. Reviewed by: ru, sam, jhb
* Fix "struct ifnet" leaks when attach() fails in the middle, e.g.ru2005-09-161-2/+2
| | | | | | when mii_phy_probe() or bus_setup_intr() fails. For drivers that call their detach() in this case, call if_free() there to cover this case too.
* Propagate rename of IFF_OACTIVE and IFF_RUNNING to IFF_DRV_OACTIVE andrwatson2005-08-091-7/+7
| | | | | | | | | | | | | | IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to ifnet.if_drv_flags. Device drivers are now responsible for synchronizing access to these flags, as they are in if_drv_flags. This helps prevent races between the network stack and device driver in maintaining the interface flags field. Many __FreeBSD__ and __FreeBSD_version checks maintained and continued; some less so. Reviewed by: pjd, bz MFC after: 7 days
* Modify device drivers supporting multicast addresses to lock if_addr_mtxrwatson2005-08-031-0/+2
| | | | | | | | over iteration of their multicast address lists when synchronizing the hardware address filter with the network stack-maintained list. Problem reported by: Ed Maste (emaste at phaedrus dot sandvine dot ca> MFC after: 1 week
* Stop embedding struct ifnet at the top of driver softcs. Instead thebrooks2005-06-102-12/+19
| | | | | | | | | | | | | | | | | | | | struct ifnet or the layer 2 common structure it was embedded in have been replaced with a struct ifnet pointer to be filled by a call to the new function, if_alloc(). The layer 2 common structure is also allocated via if_alloc() based on the interface type. It is hung off the new struct ifnet member, if_l2com. This change removes the size of these structures from the kernel ABI and will allow us to better manage them as interfaces come and go. Other changes of note: - Struct arpcom is no longer referenced in normal interface code. Instead the Ethernet address is accessed via the IFP2ENADDR() macro. To enforce this ac_enaddr has been renamed to _ac_enaddr. - The second argument to ether_ifattach is now always the mac address from driver private storage rather than sometimes being ac_enaddr. Reviewed by: sobomax, sam
* Remove bus_{mem,p}io.h and related code for a micro-optimization on i386nyan2005-05-291-2/+0
| | | | | | and amd64. The optimization is a trivial on recent machines. Reviewed by: -arch (imp, marcel, dfr)
* Fix style(9) issues with __P removal.imp2005-02-241-38/+36
| | | | Noticed by: bde
* Return BUS_PROBE_DEFAULT instead of 0.imp2005-02-241-1/+1
|
* /* -> /*- for license, minor formatting changesimp2005-01-072-2/+2
|
OpenPOWER on IntegriCloud