| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
command register. The lazy BAR allocation code in FreeBSD sometimes
disables this bit when it detects a range conflict, and will re-enable
it on demand when a driver allocates the BAR. Thus, the bit is no longer
a reliable indication of capability, and should not be checked. This
results in the elimination of a lot of code from drivers, and also gives
the opportunity to simplify a lot of drivers to use a helper API to set
the busmaster enable bit.
This changes fixes some recent reports of disk controllers and their
associated drives/enclosures disappearing during boot.
Submitted by: jhb
Reviewed by: jfv, marius, achadd, achim
MFC after: 1 day
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
running state. fxp(4) requires controller reinitialization for the
following cases.
o RX lockup condition on i82557
o promiscuous mode change
o multicast filter change
o WOL configuration
o TSO/VLAN hardware tagging/checksum offloading configuration
o MAC reprogramming after speed/duplex/flow-control resolution
o Any events that result in MAC reprogramming(link UP/DOWN,
remote link partner's restart of auto-negotiation etc)
o Microcode loading/unloading
Apart from above cases which come from hardware limitation, upper
stack also blindly reinitializes controller whenever an IP address
is assigned. After r194573, fxp(4) no longer needs to reinitialize
the controller to program multicast filter after upping the
interface. So keeping track of driver running state should remove
all unnecessary controller reinitializations.
This change will also address endless controller reinitialization
triggered by dhclient(8).
Tested by: hrs, Alban Hertroys <haramrae@gmail.com>
|
|
|
|
| |
malloc(9) flags in sys/dev.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
them, please let me know if not). Most of these are of the form:
static const struct bzzt_type {
[...list of members...]
} const bzzt_devs[] = {
[...list of initializers...]
};
The second const is unnecessary, as arrays cannot be modified anyway,
and if the elements are const, the whole thing is const automatically
(e.g. it is placed in .rodata).
I have verified this does not change the binary output of a full kernel
build (except for build timestamps embedded in the object files).
Reviewed by: yongari, marius
MFC after: 1 week
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
deterministically handled after the corresponding PHY drivers when
loaded as modules. Otherwise, when these MAC/PHY driver pairs are
compiled into a single module probing the PHY driver may fail. This
makes r151438 and r226154 actually work. [1]
Reported and tested by: yongari (fxp(4))
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
Submitted by: jhb [1]
MFC after: 3 days
|
|
|
|
|
|
|
|
|
| |
violation should be activated unless the system is cold-booted
after updating EEPROM.
The PCI protocol violation happens only when established link is
10Mbps so the workaround should be updated whenever link state
change is detected. Previously the workaround was activated only
when user checks current media status with ifconfig(8).
|
|
|
|
|
|
|
|
|
|
|
| |
whether the checksum of EEPROM is valid or not. Because driver
heavily relies on EEPROM information when it selectively enables
features/workarounds, it would be helpful to know whether driver
sees valid EEPROM.
While I'm here remove all other EEPROM accesses since the entire
EEPROM is loaded at device attach time.
MFC after: 2 weeks
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
for 82550C. For 82550 controllers this change restores CPUSaver
microcode loading. Due to silicon bug on 82550 and 82550C with
server extension, these controllers seem to require CPUSaver
microcode to receive fragmented UDP datagrams. However the
microcode shouldn't be used on client featured 82550C as it locks
up the controller. In addition, client featured 82550C does not
have the silicon bug. Also clear temporary memory used for
microcode loading since the same memory area is used for other
commands.
While I'm here use 82550C in probe message instead of generic
82550.
Reported by: Andreas Longwitz <longwitz <> incore de>
Tested by: Andreas Longwitz <longwitz <> incore de>
MFC after: 2 weeks
|
|
|
|
|
|
|
|
|
|
|
|
| |
driver is running driver would have already completed flow control
configuration. This change removes unnecessary media changes in
controller reconfiguration cases such that it does not trigger link
reestablishment for configuration change requests like promiscuous
mode change.
Reported by: Many
Tested by: Mike Tancsa <mike <> sentex dot net>
MFC after: 1 week
|
| |
|
|
|
|
|
| |
bus_dmamap_load(9) that it should return immediately with error
when there are insufficient mapping resources.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix the TCP header size calculation such that makes TSO engine
cache all header(ethernet/IP/TCP) bytes to its internal buffer.
While here, remove extra pull up for TCP payload. Unlike some
em(4) controllers, fxp(4) does not require such work around for
TSO.
The two limitations are ethernet/IP/TCP header size should be less
than or equal to the size of controller's internal buffer(80 bytes)
and these header information should be found in the first fragment
of a TSO frame.
|
|
|
|
| |
0x10.
|
|
|
|
|
|
|
|
|
|
| |
the microcode caused SCB timeouts. Linux driver does not allow
microcode loading for these controllers and jfv also confirmed that
there is no need to do and it shouldn't.
PR: kern/103332
Additional confirmation from: jfv
MFC after: 1 week
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
(reporting IFM_LOOP based on BMCR_LOOP is left in place though as
it might provide useful for debugging). For most mii(4) drivers it
was unclear whether the PHYs driven by them actually support
loopback or not. Moreover, typically loopback mode also needs to
be activated on the MAC, which none of the Ethernet drivers using
mii(4) implements. Given that loopback media has no real use (and
obviously hardly had a chance to actually work) besides for driver
development (which just loopback mode should be sufficient for
though, i.e one doesn't necessary need support for loopback media)
support for it is just dropped as both NetBSD and OpenBSD already
did quite some time ago.
- Let mii_phy_add_media() also announce the support of IFM_NONE.
- Restructure the PHY entry points to use a structure of entry points
instead of discrete function pointers, and extend this to include
a "reset" entry point. Make sure any PHY-specific reset routine is
always used, and provide one for lxtphy(4) which disables MII
interrupts (as is done for a few other PHYs we have drivers for).
This includes changing NIC drivers which previously just called the
generic mii_phy_reset() to now actually call the PHY-specific reset
routine, which might be crucial in some cases. While at it, the
redundant checks in these NIC drivers for mii->mii_instance not being
zero before calling the reset routines were removed because as soon
as one PHY driver attaches mii->mii_instance is incremented and we
hardly can end up in their media change callbacks etc if no PHY driver
has attached as mii_attach() would have failed in that case and not
attach a miibus(4) instance.
Consequently, NIC drivers now no longer should call mii_phy_reset()
directly, so it was removed from EXPORT_SYMS.
- Add a mii_phy_dev_attach() as a companion helper to mii_phy_dev_probe().
The purpose of that function is to perform the common steps to attach
a PHY driver instance and to hook it up to the miibus(4) instance and to
optionally also handle the probing, addition and initialization of the
supported media. So all a PHY driver without any special requirements
has to do in its bus attach method is to call mii_phy_dev_attach()
along with PHY-specific MIIF_* flags, a pointer to its PHY functions
and the add_media set to one. All PHY drivers were updated to take
advantage of mii_phy_dev_attach() as appropriate. Along with these
changes the capability mask was added to the mii_softc structure so
PHY drivers taking advantage of mii_phy_dev_attach() but still
handling media on their own do not need to fiddle with the MII attach
arguments anyway.
- Keep track of the PHY offset in the mii_softc structure. This is done
for compatibility with NetBSD/OpenBSD.
- Keep track of the PHY's OUI, model and revision in the mii_softc
structure. Several PHY drivers require this information also after
attaching and previously had to wrap their own softc around mii_softc.
NetBSD/OpenBSD also keep track of the model and revision on their
mii_softc structure. All PHY drivers were updated to take advantage
as appropriate.
- Convert the mebers of the MII data structure to unsigned where
appropriate. This is partly inspired by NetBSD/OpenBSD.
- According to IEEE 802.3-2002 the bits actually have to be reversed
when mapping an OUI to the MII ID registers. All PHY drivers and
miidevs where changed as necessary. Actually this now again allows to
largely share miidevs with NetBSD, which fixed this problem already
9 years ago. Consequently miidevs was synced as far as possible.
- Add MIIF_NOMANPAUSE and mii_phy_flowstatus() calls to drivers that
weren't explicitly converted to support flow control before. It's
unclear whether flow control actually works with these but typically
it should and their net behavior should be more correct with these
changes in place than without if the MAC driver sets MIIF_DOPAUSE.
Obtained from: NetBSD (partially)
Reviewed by: yongari (earlier version), silence on arch@ and net@
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
makes controller to receive bad frames and i82557 will also receive
bad frames since fxp(4) have to receive VLAN oversized frames. If
fxp(4) encounter DMA overrun error, the received frame size would
be 0 so the actual frame size after checksum field extraction the
length would be negative(-2). Due to signed/unsigned comparison
used in driver, frame length check did not work for DMA overrun
frames. Correct this by casting it to int.
While I'm here explicitly check DMA overrun error and discard the
frame regardless of result of received frame length check.
Reported by: n_hibma
Tested by: n_hibma
MFC after: 1 week
|
|
|
|
| |
pci_find_cap() instead.
|
|
|
|
|
| |
coherent.
- Update a comment to no longer reference Alpha.
|
|
|
|
|
|
|
|
|
|
|
| |
caused link re-negotiation whenever application joins or leaves a
multicast group. If driver is running, it would have established a
link so there is no need to start re-negotiation. The re-negotiation
broke established link which in turn stopped multicast application
working while re-negotiation is in progress.
PR: kern/154667
MFC after: 1 week
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
the controller to workaround silicon bug of i82557. Each reset will
re-establish link which in turn triggers MII status change
callback. The callback will try to reconfigure controller if the
controller is not i82557 to enable flow-control. This caused
endless link UP/DOWN when the workaround was enabled on non-i82557
controller.
To fix the issue, apply RX lockup workaround only for i82557.
Previously it blindly checked undocumented EEPROM location such
that it sometimes enabled the workaround for other controllers. At
this time, only i82557 is known to have the silicon bug.
This fixes a regression introduced in r215906 which enabled flow
control support for all controllers except i82557.
Reported by: Karl Denninger (karl <> denninger dot net)
Tested by: Karl Denninger (karl <> denninger dot net)
MFC after: 3 days
|
|
|
|
|
|
|
|
| |
the dev.fxp.%d.noflow tunable as the same effect can now be achieved with
ifconfig(8) by setting the flowcontrol media option as desired (besides
the tunable never having a chance to actually enable flow control support
so far).
In joint forces with: yongari
|
|
|
|
|
| |
- Remove an alpha remnant.
- Minor comment and style fixes.
|
|
|
|
|
|
|
|
|
| |
VLAN hardware tagging to make TSO work over VLAN. So if VLAN
hardware tagging is disabled explicitly clear TSO over VLAN. While
I'm here allow disabling VLAN TX checksum offloading.
Tested by: Liudas < liudasb <> centras dot lt >
MFC after: 10 days
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
the NIC drivers as well as the PHY drivers to take advantage of the
mii_attach() introduced in r213878 to get rid of certain hacks. For
the most part these were:
- Artificially limiting miibus_{read,write}reg methods to certain PHY
addresses; we now let mii_attach() only probe the PHY at the desired
address(es) instead.
- PHY drivers setting MIIF_* flags based on the NIC driver they hang
off from, partly even based on grabbing and using the softc of the
parent; we now pass these flags down from the NIC to the PHY drivers
via mii_attach(). This got us rid of all such hacks except those of
brgphy() in combination with bce(4) and bge(4), which is way beyond
what can be expressed with simple flags.
While at it, I took the opportunity to change the NIC drivers to pass
up the error returned by mii_attach() (previously by mii_phy_probe())
and unify the error message used in this case where and as appropriate
as mii_attach() actually can fail for a number of reasons, not just
because of no PHY(s) being present at the expected address(es).
Reviewed by: jhb, yongari
|
|
|
|
|
|
|
|
|
|
|
| |
header parser uses m_pullup(9) to get access to mbuf chain.
m_pullup(9) can allocate new mbuf chain and free old one if the
space left in the mbuf chain is not enough to hold requested
contiguous bytes. Previously drivers can use stale ip/tcp header
pointer if m_pullup(9) returned new mbuf chain.
Reported by: Andrew Boyer (aboyer <> averesystems dot com)
MFC after: 10 days
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
|
|
|
|
| |
EINPROGRESS.
|
|
|
|
| |
Add missing BUS_DMASYNC_POSTWRITE and BUS_DMASYNC_PREREAD.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
fxp(4) already used to extract most hardware MAC statistics but it
didn't show them. With this change, all MAC statistics counters
are exported. Because there are a couple of new counters for 82558
and 82559, enable extended MAC statistics functionality to get
these counters. Accoring to public data sheet, 82559 MAC statistics
return 24 DWORD counters(3 counters are unknown at this moment) so
increase MAC counter structure to meet the MAC statistics block size.
The completion of MAC counter dump is now checked against
FXP_STATS_DR_COMPLETE status code which is appended at the end of
status block. Previously fxp(4) ignored the status of the
FXP_SCB_COMMAND_CU_DUMPRESET command. fxp(4) does not wait for the
completion of pending command before issuing
FXP_SCB_COMMAND_CU_DUMPRESET. Instead it skips the command and try
it next time. This scheme may show better performance but there is
chance to loose updated counters after stopping controller. So make
sure to update MAC statistics in fxp_stop().
While I'm here move sysctl node creation to fxp_sysctl_node().
Tested by: Larry Baird < lab <> gta dot com >
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
table. The default size of the configuration table was 22 bytes. To
use extended feature of 82550/82551 the configuration table size
was expanded to 32 bytes. The added configuration for 82550/82551
specifies VLAN hardware tagging and IPSec configuration as well as
TCO.
To make configuration easier fxp(4) used a configuration template
and the template was copied to configuration table. After that,
some parameters of the configuration table was changed depending on
controller type and operation mode. However the size of template
was 22 bytes so some configuration parameters were not properly
initialized on 82550/82551.
Fix this by increasing the template size. For 82557, 82558 and
82559 the size of the configuration is still 22 bytes.
|
|
|
|
|
|
|
|
|
|
|
| |
unicast and the other for multicast. To receive multicast frames
that host didn't join in promiscuous mode, driver have to set
promiscuous mode for multicast frames as well.
The Open Source Software Developer Manual for i8255x was not clear
how to handle promiscuous mode.
PR: kern/145905
MFC after: 5 days
|
|
|
|
|
| |
drivers to take into account for the change. Basically CSUM_TSO
should be checked before checking CSUM_TCP.
|
|
|
|
|
|
|
|
|
| |
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
|
|
|
|
| |
know better than to commit with a cat in the area.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
To detect which controller is ICH based one, add a new member
variable ich to struct fxp_ident and move the struct to
if_fxpvar.h. Since I've faked controller revision, don't allow
microcode loading for ICH based controllers.
With this change all ICH based controllers will have WOL and Rx
checksum offload capability.
PR: kern/135451
Tested by: Alexey Shuvaev ( shuvaev <> physik dot uni-wuerzburg dot de ),
pluknet ( pluknet <> gmail dot com ),
Gary Jennejohn ( gary.jennejohn <> freenet dot de )
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
not allow multicast filter programming when controller is busy to
send/receive frames. So it used to mark need_mcsetup bit and defer
multicast filter programming until controller becomes idle state.
To detect when the controller is idle fxp(4) relied on Tx
completion interrupt with NOP command and fxp_start_body and
fxp_intr_body had to see whether pending multicast filter
programming was requested. This resulted in very complex logic and
sometimes it did not work as expected.
Since the controller should be in idle state before any multicast
filter modifications I changed it to reinitialize the controller
whenever multicast filter programming is required. This is the same
way what OpenBSD and NetBSD does. Also I added IFF_DRV_RUNNING
check in ioctl handler so controller would be reinitialized only if
it is absolutely needed.
With this change I guess we can remove fxp(4) DELAY hack in ifioctl
for IPv6 case.
|
|
|
|
|
|
|
|
| |
upper stack in fxp_start_body().
fxp(4) drops driver lock in Rx path so check the fxp(4) is still
running after reacquiring driver lock in Rx path. Also don't
invoke fxp_intr_body if fxp(4) is not running. With this change
there is no need to set suspend bit in device attach phase.
|
|
|
|
|
|
| |
the Rx lock-up workaround.
Obtained from: NetBSD
|
|
|
|
|
|
|
|
|
| |
hardware reset in attach phase. Selective reset does not clear
configured parameters so I think full hardware reset is required.
To prevent PCI bus lock-up, do selective reset first which will get
off the controller from PCI bus and request software reset after
selective reset. Software reset will unmask interrupts so disable
it after the reset.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
common mbuf dma tag for both Tx and Rx path but Rx buffer should
have single DMA segment and maximum buffer size of the segment
should be less than MCLBYTES.
fxp(4) also have to check Tx completion status which was updated by
DMA so we need BUS_DMASYNC_PREREAD and BUS_DMASYNC_POSTWRITE
synchronization in Tx path. Fix all misuse of bus_dmamap_sync(9) in
fxp(4). I guess this change shall fix occasional driver breakage in
PAE environments.
While I'm here add error messages of dma tag/buffer creation and
correct messages.
|
|
|
|
|
|
|
|
|
| |
driver should read updated status back after issuing a SCB command.
To send a command to controller and read updated status back,
driver should synchronize both memory read and write operations
with device. Fix bus_dmamap_sync operation specifier used in
fxp_dma_wait() by adding both memory read and memory write
operations.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
|
|
|
|
|
|
|
|
|
|
| |
Remote host can advertise smaller MSS than that of sender so upper
stack might have adjusted the MSS which in turn generates IP
packets that are less size than that of interface MTU.
Reported by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
Tested by: Bjoern Koenig ( bkoenig <> alpha-tierchen dot de )
MFC after: 3 days
|
| |
|
| |
|
|
|
|
|
| |
When fxp(4) intializes Rx buffers for the first time, there is no
loaded dma map so attempting to unload it is an invalid operation.
|
|
|
|
|
|
| |
payload length in TSO case. Leaving unused TBD also seem to cause
SCB timeouts under certain conditions when TSO/non-TSO traffics
are active at the same time.
|