| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| | |
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
o Grab the MAC address out of the CIS if the card has the special
3Com 0x88 tuple. Most 3Com cards don't have this tuple, but we
prefer it to the eeprom since it only appears to be present when
the eeprom doesn't have the info. So far, I've only observed this
on my 3C362 and 3C362B cards, but the NetBSD driver implies that
the 3C362C also has this tuple, and that some 3C574 cards do too (none
of mine do). ep_pccard_mac was written after looking at the NetBSD
code.
o Store the enet addr in the softc for this device, so we can use the
overridden MAC to set the station address.
o Create a routine to set the station address and use it where we need it.
o setup the cmd shitfs and such before we call ep_alloc(), and remove
setting up the cmd shift value there. It initializes to 0, and those
attachments that need to frob it do so before calling ep_alloc.
o Remove some obsolete comments
o No longer a need to export ep_get_macaddr, so make it static
o ep_alloc already grabs the EEPROM id, so we don't need to grab it again
in ep_pccard_attach.
o eliminate unit, it isn't needed, fix some printfs to be device_printf
instead.
# All my pccards except the 3C1 work now. Didn't test ISA or cbus cards
# that I have: 3C509B-TP or 3C569B-J-TPO
Tested on: 3C589B, 3C589C, 3C589D, 3C589D-TP, 3C562, 3C562B/3C563B,
3C562D/3C563D, 3CCFE574BT, 3CXEM556, 3CCSH572BT, 3C574-TX,
3CCE589EC, 3CXE589EC, 3CCFEM556, 3C1
Approved by: re (scottl)
|
| |
|
|
|
|
|
|
|
| |
that says why we do this (or rather, explains that it is some voodoo magic
that's poorly understood). The local buffer fixes the crash on attach.
o Rename get_e() to ep_get_e() to avoid namespace pollution.
Submitted by: mux
Approved by: re (scottl)
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
|
| | |
|
| | |
|
| |
|
|
|
|
| |
o give an argument to EP_BUSY_WAIT
o use foo_locked rather than foo_body
o Add locking assertions for extra safety.
|
| |
|
|
|
|
|
|
| |
o Make the driver MPSAFE
o Some changes due to diff reduction effort with vx.
o Removed some obsolete junk.
Reviewed by: sam, modd
|
| | |
|
| | |
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Use EP_{READ,WRITE}{,_MULTI}_{1,2,4} instead. I've had several people
submit patches like this over the years of varying qualities, markm
being the last. The names were chosen in consulation with mdodd on
irc.
I've tested this with only PCMCIA cards: 3CCE589EC and 3CCSH572BT.
I've not tried with my more extensive ISA, EISA and cbus collection.
Reviewed by: mdodd
|
| |
|
|
|
|
|
| |
The next round of commits will be to fix up locking in it. This lot
is to at least give a consistent base to work off.
OK'ed by: imp, mdodd
|
| |
|
|
|
| |
- Move ep_pccard_detach() to if_ep.c and rename to ep_detach()
- Specify detach methods for all bus frontends.
|
| |
|
|
|
| |
- Modify ep_get_macaddr() to return an error status.
- Reverse the return value logic of eeprom_rdy().
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
|
| |
|
|
|
|
|
| |
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- Rip out all the static softc stuff and do softc allocation the right way.
- Rewrite most of the ISA code so that it provides a DEVICE_IDENTIFY
method to enumerate all non-PnP ISA devices.
This has the following consequences:
- No 'ep' devices may be hardwired.
- All hardwired devices will probably be detected twice.
By hardwired I mean:
device ep0 at isa? port 0x300 irq 10
- 'ep' devices are ordered by bus, slot, and then MAC address.
- Make 3c509B cards work in PnP mode. Yes, they really work.
- Convert over to using ifmedia for media selection. No more of this
lame 'linkX' stuff.
- Consolidate a lot of duplicated code.
- Make a stab at not breaking MII based PCCARD devices.
I doubt that the PCCARD stuff works any more than it did before my
changes but theres hope. My PCCARD hardware should arrive in a
week or so.
- Retreive the media settings from the card EEPROM rather than guessing.
I've got a 3c509-TPO that thinks its got an AUI port and if others
can report similar problems I'll write a bit of clever code that will
fix this but right now it works correctly on all but 1 card.
- Clean up a few things and make some cosmetic changes.
- Add myself as the MAINTAINER since nobody else wants to. I'm
in the best position to do this as I've got an example of most
of the cards:
EISA 3c579 bnc/aui
MCA 3c529 tp/aui
ISA 3c509 tpo
ISA-PnP 3c509B combo
If someone wants to send me a any cards I don't have I'd appriciate
it. Also welcome are 3c59x boards since I'll be folding if_vx and
if_ep at some point.
|
| |
|
|
|
|
|
|
|
|
|
| |
I'm committing this from a laptop running this driver. Have only one
devclass for all ep devices (at least for pccard and eisa) so unit
numbering is sane. Might not work with both isa and non-isa devices
on the same system until ep is updated (Matt has some patches in the
pipeline which should resolve this, he wanted me to commit this so he
can resolve any conflicts against cvs rather than my patches).
Reviewed by: Matt Dodd <mdodd@freebsd.org>
|
|
|
- Split out the prototypes, externs and struct decls from if_epreg.h into
if_epvar.h.
- Add support for MCA based Etherlink III (3c529) devices.
None of this code is used right now; the old if_ep driver is still
in place and used.
I will eventually get around to converting if_ep_isa.c to newbus once I've
had a talk with Peter and DFR about the DEVICE_IDENTIFY() method.
I have tested this code on my PS/2. It works. I would like EISA and ISA
testers since my example hardware hasn't arrived yet.
Add:
dev/ep/if_ep.c optional ep
dev/ep/if_ep_isa.c optional ep isa
dev/ep/if_ep_eisa.c optional ep eisa
dev/ep/if_ep_mca.c optional ep mca
dev/ep/if_ep_pccard.c optional ep card
to sys/conf/files
Remove:
i386/eisa/3c5x9.c optional ep
i386/isa/if_ep.c optional ep
from sys/i386/conf/files.i386
PCCARD testers wanted!
I will switch off and cvs rm the old driver in favor of this copy once
I've had positive feedback or have the hardware to verify that it works.
|
