diff options
Diffstat (limited to 'sys/dev/usb/uhci.c')
| -rw-r--r-- | sys/dev/usb/uhci.c | 112 |
1 files changed, 99 insertions, 13 deletions
diff --git a/sys/dev/usb/uhci.c b/sys/dev/usb/uhci.c index 6573e0a..a18ad43 100644 --- a/sys/dev/usb/uhci.c +++ b/sys/dev/usb/uhci.c @@ -1,7 +1,7 @@ /* $NetBSD: uhci.c,v 1.160 2002/05/28 12:42:39 augustss Exp $ */ /* $FreeBSD$ */ -/* Also incorporated from NetBSD: 1.165 */ +/* Also incorporated from NetBSD: 1.165, 166 */ /* * Copyright (c) 1998 The NetBSD Foundation, Inc. @@ -169,6 +169,7 @@ struct uhci_pipe { }; Static void uhci_globalreset(uhci_softc_t *); +Static usbd_status uhci_portreset(uhci_softc_t*, int); Static void uhci_reset(uhci_softc_t *); #if defined(__NetBSD__) || defined(__OpenBSD__) Static void uhci_shutdown(void *v); @@ -2981,6 +2982,101 @@ uhci_str(usb_string_descriptor_t *p, int l, char *s) } /* + * The USB hub protocol requires that SET_FEATURE(PORT_RESET) also + * enables the port, and also states that SET_FEATURE(PORT_ENABLE) + * should not be used by the USB subsystem. As we cannot issue a + * SET_FEATURE(PORT_ENABLE) externally, we must ensure that the port + * will be enabled as part of the reset. + * + * On the VT83C572, the port cannot be successfully enabled until the + * outstanding "port enable change" and "connection status change" + * events have been reset. + */ +Static usbd_status +uhci_portreset(uhci_softc_t *sc, int index) +{ + int lim, port, x; + + if (index == 1) + port = UHCI_PORTSC1; + else if (index == 2) + port = UHCI_PORTSC2; + else + return (USBD_IOERROR); + + x = URWMASK(UREAD2(sc, port)); + UWRITE2(sc, port, x | UHCI_PORTSC_PR); + + usb_delay_ms(&sc->sc_bus, USB_PORT_ROOT_RESET_DELAY); + + DPRINTFN(3,("uhci port %d reset, status0 = 0x%04x\n", + index, UREAD2(sc, port))); + + x = URWMASK(UREAD2(sc, port)); + UWRITE2(sc, port, x & ~UHCI_PORTSC_PR); + + delay(100); + + DPRINTFN(3,("uhci port %d reset, status1 = 0x%04x\n", + index, UREAD2(sc, port))); + + x = URWMASK(UREAD2(sc, port)); + UWRITE2(sc, port, x | UHCI_PORTSC_PE); + + for (lim = 10; --lim > 0;) { + usb_delay_ms(&sc->sc_bus, USB_PORT_RESET_DELAY); + + x = UREAD2(sc, port); + + DPRINTFN(3,("uhci port %d iteration %u, status = 0x%04x\n", + index, lim, x)); + + if (!(x & UHCI_PORTSC_CCS)) { + /* + * No device is connected (or was disconnected + * during reset). Consider the port reset. + * The delay must be long enough to ensure on + * the initial iteration that the device + * connection will have been registered. 50ms + * appears to be sufficient, but 20ms is not. + */ + DPRINTFN(3,("uhci port %d loop %u, device detached\n", + index, lim)); + break; + } + + if (x & (UHCI_PORTSC_POEDC | UHCI_PORTSC_CSC)) { + /* + * Port enabled changed and/or connection + * status changed were set. Reset either or + * both raised flags (by writing a 1 to that + * bit), and wait again for state to settle. + */ + UWRITE2(sc, port, URWMASK(x) | + (x & (UHCI_PORTSC_POEDC | UHCI_PORTSC_CSC))); + continue; + } + + if (x & UHCI_PORTSC_PE) + /* Port is enabled */ + break; + + UWRITE2(sc, port, URWMASK(x) | UHCI_PORTSC_PE); + } + + DPRINTFN(3,("uhci port %d reset, status2 = 0x%04x\n", + index, UREAD2(sc, port))); + + if (lim <= 0) { + DPRINTFN(1,("uhci port %d reset timed out\n", index)); + return (USBD_TIMEOUT); + } + + sc->sc_isreset = 1; + return (USBD_NORMAL_COMPLETION); +} + +/* * Simulate a hardware hub by handling all the necessary requests. */ usbd_status @@ -3290,18 +3386,8 @@ uhci_root_ctrl_start(usbd_xfer_handle xfer) UWRITE2(sc, port, x | UHCI_PORTSC_SUSP); break; case UHF_PORT_RESET: - x = URWMASK(UREAD2(sc, port)); - UWRITE2(sc, port, x | UHCI_PORTSC_PR); - usb_delay_ms(&sc->sc_bus, USB_PORT_ROOT_RESET_DELAY); - UWRITE2(sc, port, x & ~UHCI_PORTSC_PR); - delay(100); - x = UREAD2(sc, port); - UWRITE2(sc, port, x | UHCI_PORTSC_PE); - usb_delay_ms(&sc->sc_bus, 10); /* XXX */ - DPRINTFN(3,("uhci port %d reset, status = 0x%04x\n", - index, UREAD2(sc, port))); - sc->sc_isreset = 1; - break; + err = uhci_portreset(sc, index); + goto ret; case UHF_PORT_POWER: /* Pretend we turned on power */ err = USBD_NORMAL_COMPLETION; |
