1 files changed, 248 insertions, 0 deletions
diff --git a/share/man/man4/natmip.4 b/share/man/man4/natmip.4
new file mode 100644
index 0000000..154e97d
--- /dev/null
+++ b/share/man/man4/natmip.4
@@ -0,0 +1,248 @@
+.\"
+.\" Copyright (c) 2003
+.\"	Fraunhofer Institute for Open Communication Systems (FhG Fokus).
+.\" 	All rights reserved.
+.\"
+.\" Author: Hartmut Brandt <harti@FreeBSD.org>
+.\"
+.\" Redistribution and use in source and binary forms, with or without
+.\" modification, are permitted provided that the following conditions
+.\" are met:
+.\" 1. Redistributions of source code must retain the above copyright
+.\"    notice, this list of conditions and the following disclaimer.
+.\" 2. Redistributions in binary form must reproduce the above copyright
+.\"    notice, this list of conditions and the following disclaimer in the
+.\"    documentation and/or other materials provided with the distribution.
+.\"
+.\" THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND
+.\" ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+.\" IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+.\" ARE DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE
+.\" FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+.\" DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
+.\" OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
+.\" HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT
+.\" LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
+.\" OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
+.\" SUCH DAMAGE.
+.\"
+.\" $FreeBSD$
+.\"
+.Dd August 11, 2003
+.Dt NATMIP 4
+.Os
+.Sh NAME
+.Nm natmip
+.Nd IP over ATM PVCs
+.Sh SYNOPSIS
+.Cd "device atm"
+.Cd "options NATM"
+.Sh DESCRIPTION
+The NATM protocol stack includes support for IP over ATM.
+Without any
+additional signalling stacks or other modules it is possible to build
+a CLIP (classical IP over ATM) network based on PVCs.
+.Pp
+An ATM network card
+.Li ( en0
+in this example) is configured for IP by something
+like:
+.Pp
+.Dl "ifconfig en0 128.252.200.1 netmask 0xffffff00 up"
+.Pp
+IP routing is done with special interface routes (routes with directly
+reachable destinations) with a link layer gateway address.
+The link layer address specifies the ATM interface through which the
+destination can be reached, the virtual channel that connects to the
+destination and the ATM characteristics of this channel.
+The address part of the link layer address (see
+.Xr link_addr 3 )
+consists of a fixed part (the first 5 bytes) and a part that
+depends on the kind of the PVC (UBR, CBR, VBR, ABR).
+Multi-byte values
+are big-endian encoded: the bytes with the lower numbers contain the
+higher order bits.
+.Bl -tag -width "bytes 12...12" -offset indent
+.It byte 0
+Is a flag byte.
+Currently only flag 0x20 is used.
+When set, all IP frames are LLC/SNAP encapsulated before putting them into
+an AAL5 frame.
+Setting this flag is recommended and allows interoperability with other
+CLIP implementations.
+Note that BPF works only with LLC/SNAP encapsulation.
+.It byte 1
+This is the VPI of the channel.
+.It bytes 2...3
+VCI of the channel.
+Must not be zero.
+.It byte 4
+Traffic type.
+One of 0 (UBR), 1 (CBR), 2 (ABR), 3 (VBR).
+.El
+.Pp
+The variable part for UBR connections may be either empty or three bytes:
+.Bl -tag -width "bytes 12...12" -offset indent
+.It bytes 5...7
+Specifies the peak cell rate for UBR.
+.El
+.Pp
+The variable part for CBR connections must be three bytes:
+.Bl -tag -width "bytes 12...12" -offset indent
+.It bytes 5...7
+Specifies the peak cell rate for CBR.
+.El
+.Pp
+The variable part for VBR connections must be 9 bytes long and specifies three
+values:
+.Bl -tag -width "bytes 12...12" -offset indent
+.It bytes 5...7
+Specifies the peak cell rate for VBR.
+.It bytes 8...10
+This is the sustainable cell rate.
+.It bytes 11...13
+The maximum burst size.
+.El
+.Pp
+The variable part for ABR connections must be 19 bytes long and specifies the
+following values:
+.Bl -tag -width "bytes 12...12" -offset indent
+.It bytes 5...7
+Specifies the peak cell rate for ABR.
+.It bytes 8...10
+The minimum cell rate.
+.It bytes 11...13
+The initial cell rate.
+.It bytes 14...16
+The transient buffer exposure.
+.It byte 17
+The NRM value.
+.It byte 18
+The TRM value.
+.It bytes 19...20
+The ADTF value.
+.It byte 21
+The rate increase factor (RIF).
+.It byte 22
+The rate decrease factor (RDF).
+.It byte 23
+The cutoff decrease factor (CDF).
+.El
+.Pp
+To add a PVC the
+.Xr route 8
+utility can be used:
+.Bd -ragged -offset indent
+.Nm route Cm add
+.Fl iface Aq Ar "remote\ IP\ address"
+.Fl link Ao Ar iface Ac : Ns Aq Ar lladdr
+.Ed
+.Pp
+The
+.Ar iface
+is the ATM interface through which
+.Ar "remote\ IP\ address"
+can be reached and
+.Ar lladdr
+is the link layer address as a string of dot-separated, hexadecimal bytes.
+.Pp
+NATM also supports the old, original format.
+This consists of 4 byte
+link layer addresses (and the channels are implicit UBR):
+.Bl -tag -width "bytes 12...12" -offset indent
+.It byte 0
+Flags:
+.Bl -tag -width "0x02" -offset indent -compact
+.It 0x01
+use AAL5.
+.It 0x02
+if using AAL5, use an LLC/SNAP header.
+.El
+.Pp
+Thus, parameter 3 means AAL5 and LLC/SNAP encapsulation (this is the required
+setting for interworking with other CLIP clients).
+Note that BPF works only with LLC/SNAP encapsulation.
+.It byte 1
+VPI for the channel
+.It bytes 2...3
+VCI for the channel
+.El
+.Sh EXAMPLES
+Suppose you have 3 hosts 128.252.200.1, 128.252.200.2 and
+128.252.200.3 connected by ATM through PVCs:
+.Pp
+.Bl -item -offset indent -compact
+.It
+between 128.252.200.1 and 128.252.200.2: 0xc9 UBR
+.It
+between 128.252.200.1 and 128.252.200.3: 0xca VBR
+.It
+between 128.252.200.2 and 128.252.200.3: 0xcb CBR
+.El
+.Pp
+The parameters for the VBR channel are: PCR 50000, SCR 10000, MBS 10.
+The peak cell rate for the CBR channel is 100000.
+.Pp
+To enable the links use the following commands:
+.Pp
+on host 128.252.200.1:
+.Bd -literal -offset indent -compact
+ifconfig en0 128.252.200.1 netmask 0xffffff00 up
+route add -iface 128.252.200.2 -link en0:3.0.0.c9.0
+route add -iface 128.252.200.3 -link en0:3.0.0.ca.3.0.c3.50.0.27.10.0.0.a
+.Ed
+.Pp
+on host 128.252.200.2:
+.Bd -literal -offset indent -compact
+ifconfig en0 128.252.200.2 netmask 0xffffff00 up
+route add -iface 128.252.200.1 -link en0:3.0.0.c9.0
+route add -iface 128.252.200.3 -link en0:3.0.0.cb.1.1.86.a0
+.Ed
+.Pp
+on host 128.252.200.3:
+.Bd -literal -offset indent -compact
+ifconfig en0 128.252.200.3 netmask 0xffffff00 up
+route add -iface 128.252.200.1 -link en0:3.0.0.ca.3.0.c3.50.0.27.10.0.0.a
+route add -iface 128.252.200.2 -link en0:3.0.0.cb.1.1.86.a0
+.Ed
+.Pp
+This can also be done in
+.Xr rc.conf 5 :
+.Pp
+on host 128.252.200.1:
+.Bd -literal -offset indent -compact
+network_interfaces="lo0 en0"
+ifconfig_en0="inet 128.252.200.1 netmask 255.255.255.0"
+static_routes="host2 host3"
+route_host2="-iface 128.252.200.2 -link en0:3.0.0.c9.0"
+route_host3="-iface 128.252.200.3 -link en0:3.0.0.ca.3.0.c3.50.0.27.10.0.0.a"
+.Ed
+.Pp
+on host 128.252.200.2:
+.Bd -literal -offset indent -compact
+network_interfaces="lo0 en0"
+ifconfig_en0="inet 128.252.200.2 netmask 255.255.255.0"
+static_routes="host1 host3"
+route_host1="-iface 128.252.200.1 -link en0:3.0.0.c9.0"
+route_host3="-iface 128.252.200.3 -link en0:3.0.0.cb.1.1.86.a0"
+.Ed
+.Pp
+on host 128.252.200.3:
+.Bd -literal -offset indent -compact
+network_interfaces="lo0 en0"
+ifconfig_en0="inet 128.252.200.3 netmask 255.255.255.0"
+static_routes="host1 host2"
+route_host1="-iface 128.252.200.1 -link en0:3.0.0.ca.3.0.c3.50.0.27.10.0.0.a"
+route_host2="-iface 128.252.200.2 -link en0:3.0.0.cb.1.1.86.a0"
+.Ed
+.Sh SEE ALSO
+.Xr en 4 ,
+.Xr fatm 4 ,
+.Xr hatm 4 ,
+.Xr natm 4 ,
+.Xr patm 4
+.Sh AUTHORS
+.An Chuck Cranor
+of Washington University implemented the NATM protocol layer
+along with the EN ATM driver in 1996 for
+.Nx .