diff options
Diffstat (limited to 'contrib/wpa/wpa_supplicant/defconfig')
| -rw-r--r-- | contrib/wpa/wpa_supplicant/defconfig | 157 |
1 files changed, 138 insertions, 19 deletions
diff --git a/contrib/wpa/wpa_supplicant/defconfig b/contrib/wpa/wpa_supplicant/defconfig index 8c32cb3..711b407 100644 --- a/contrib/wpa/wpa_supplicant/defconfig +++ b/contrib/wpa/wpa_supplicant/defconfig @@ -78,10 +78,15 @@ CONFIG_DRIVER_ATMEL=y #CONFIG_DRIVER_RALINK=y # Driver interface for generic Linux wireless extensions +# Note: WEXT is deprecated in the current Linux kernel version and no new +# functionality is added to it. nl80211-based interface is the new +# replacement for WEXT and its use allows wpa_supplicant to properly control +# the driver to improve existing functionality like roaming and to support new +# functionality. CONFIG_DRIVER_WEXT=y # Driver interface for Linux drivers using the nl80211 kernel interface -#CONFIG_DRIVER_NL80211=y +CONFIG_DRIVER_NL80211=y # Driver interface for FreeBSD net80211 layer (e.g., Atheros driver) #CONFIG_DRIVER_BSD=y @@ -109,11 +114,6 @@ CONFIG_DRIVER_WEXT=y # Driver interface for development testing #CONFIG_DRIVER_TEST=y -# Include client MLME (management frame processing) for test driver -# This can be used to test MLME operations in hostapd with the test interface. -# space. -#CONFIG_CLIENT_MLME=y - # Driver interface for wired Ethernet drivers CONFIG_DRIVER_WIRED=y @@ -123,6 +123,10 @@ CONFIG_DRIVER_WIRED=y # Driver interface for no driver (e.g., WPS ER only) #CONFIG_DRIVER_NONE=y +# Solaris libraries +#LIBS += -lsocket -ldlpi -lnsl +#LIBS_c += -lsocket + # Enable IEEE 802.1X Supplicant (automatically included if any EAP method is # included) CONFIG_IEEE8021X_EAPOL=y @@ -161,6 +165,9 @@ CONFIG_EAP_OTP=y # EAP-PSK (experimental; this is _not_ needed for WPA-PSK) #CONFIG_EAP_PSK=y +# EAP-pwd (secure authentication using only a password) +#CONFIG_EAP_PWD=y + # EAP-PAX #CONFIG_EAP_PAX=y @@ -190,6 +197,15 @@ CONFIG_EAP_LEAP=y # Wi-Fi Protected Setup (WPS) #CONFIG_WPS=y +# Enable WSC 2.0 support +#CONFIG_WPS2=y +# Enable WPS external registrar functionality +#CONFIG_WPS_ER=y +# Disable credentials for an open network by default when acting as a WPS +# registrar. +#CONFIG_WPS_REG_DISABLE_OPEN=y +# Enable WPS support with NFC config method +#CONFIG_WPS_NFC=y # EAP-IKEv2 #CONFIG_EAP_IKEV2=y @@ -206,6 +222,9 @@ CONFIG_SMARTCARD=y # Enable this if EAP-SIM or EAP-AKA is included #CONFIG_PCSC=y +# Support HT overrides (disable HT/HT40, mask MCS rates, etc.) +#CONFIG_HT_OVERRIDES=y + # Development testing #CONFIG_EAPOL_TEST=y @@ -213,6 +232,7 @@ CONFIG_SMARTCARD=y # unix = UNIX domain sockets (default for Linux/*BSD) # udp = UDP sockets using localhost (127.0.0.1) # named_pipe = Windows Named Pipe (default for Windows) +# udp-remote = UDP sockets with remote access (only for tests systems/purpose) # y = use default (backwards compatibility) # If this option is commented out, control interface is not included in the # build. @@ -224,6 +244,10 @@ CONFIG_CTRL_IFACE=y # the resulting binary. #CONFIG_READLINE=y +# Include internal line edit mode in wpa_cli. This can be used as a replacement +# for GNU Readline to provide limited command line editing and history support. +#CONFIG_WPA_CLI_EDIT=y + # Remove debugging code that is printing out debug message to stdout. # This can be used to reduce the size of the wpa_supplicant considerably # if debugging code is not needed. The size reduction can be around 35% @@ -285,6 +309,9 @@ CONFIG_BACKEND=file # eloop_none = Empty template #CONFIG_ELOOP=eloop +# Should we use poll instead of select? Select is used by default. +#CONFIG_ELOOP_POLL=y + # Select layer 2 packet implementation # linux = Linux packet socket (default) # pcap = libpcap/libdnet/WinPcap @@ -297,26 +324,30 @@ CONFIG_BACKEND=file # PeerKey handshake for Station to Station Link (IEEE 802.11e DLS) CONFIG_PEERKEY=y -# IEEE 802.11w (management frame protection) -# This version is an experimental implementation based on IEEE 802.11w/D1.0 -# draft and is subject to change since the standard has not yet been finalized. +# IEEE 802.11w (management frame protection), also known as PMF # Driver support is also needed for IEEE 802.11w. #CONFIG_IEEE80211W=y # Select TLS implementation # openssl = OpenSSL (default) -# gnutls = GnuTLS (needed for TLS/IA, see also CONFIG_GNUTLS_EXTRA) +# gnutls = GnuTLS # internal = Internal TLSv1 implementation (experimental) # none = Empty template #CONFIG_TLS=openssl -# Whether to enable TLS/IA support, which is required for EAP-TTLSv1. -# You need CONFIG_TLS=gnutls for this to have any effect. Please note that -# even though the core GnuTLS library is released under LGPL, this extra -# library uses GPL and as such, the terms of GPL apply to the combination -# of wpa_supplicant and GnuTLS if this option is enabled. BSD license may not -# apply for distribution of the resulting binary. -#CONFIG_GNUTLS_EXTRA=y +# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1) +# can be enabled to get a stronger construction of messages when block ciphers +# are used. It should be noted that some existing TLS v1.0 -based +# implementation may not be compatible with TLS v1.1 message (ClientHello is +# sent prior to negotiating which version will be used) +#CONFIG_TLSV11=y + +# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2) +# can be enabled to enable use of stronger crypto algorithms. It should be +# noted that some existing TLS v1.0 -based implementation may not be compatible +# with TLS v1.2 message (ClientHello is sent prior to negotiating which version +# will be used) +#CONFIG_TLSV12=y # If CONFIG_TLS=internal is used, additional library and include paths are # needed for LibTomMath. Alternatively, an integrated, minimal version of @@ -378,6 +409,17 @@ CONFIG_PEERKEY=y # Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt) #CONFIG_DEBUG_FILE=y +# Send debug messages to syslog instead of stdout +#CONFIG_DEBUG_SYSLOG=y +# Set syslog facility for debug messages +#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON + +# Add support for sending all debug messages (regardless of debug verbosity) +# to the Linux kernel tracing facility. This helps debug the entire stack by +# making it easy to record everything happening from the driver up into the +# same file, e.g., using trace-cmd. +#CONFIG_DEBUG_LINUX_TRACING=y + # Enable privilege separation (see README 'Privilege separation' for details) #CONFIG_PRIVSEP=y @@ -389,7 +431,7 @@ CONFIG_PEERKEY=y # This tracks use of memory allocations and other registrations and reports # incorrect use with a backtrace of call (or allocation) location. #CONFIG_WPA_TRACE=y -# For BSD, comment out these. +# For BSD, uncomment these. #LIBS += -lexecinfo #LIBS_p += -lexecinfo #LIBS_c += -lexecinfo @@ -398,7 +440,84 @@ CONFIG_PEERKEY=y # This enables use of libbfd to get more detailed symbols for the backtraces # generated by CONFIG_WPA_TRACE=y. #CONFIG_WPA_TRACE_BFD=y -# For BSD, comment out these. +# For BSD, uncomment these. #LIBS += -lbfd -liberty -lz #LIBS_p += -lbfd -liberty -lz #LIBS_c += -lbfd -liberty -lz + +# wpa_supplicant depends on strong random number generation being available +# from the operating system. os_get_random() function is used to fetch random +# data when needed, e.g., for key generation. On Linux and BSD systems, this +# works by reading /dev/urandom. It should be noted that the OS entropy pool +# needs to be properly initialized before wpa_supplicant is started. This is +# important especially on embedded devices that do not have a hardware random +# number generator and may by default start up with minimal entropy available +# for random number generation. +# +# As a safety net, wpa_supplicant is by default trying to internally collect +# additional entropy for generating random data to mix in with the data fetched +# from the OS. This by itself is not considered to be very strong, but it may +# help in cases where the system pool is not initialized properly. However, it +# is very strongly recommended that the system pool is initialized with enough +# entropy either by using hardware assisted random number generator or by +# storing state over device reboots. +# +# wpa_supplicant can be configured to maintain its own entropy store over +# restarts to enhance random number generation. This is not perfect, but it is +# much more secure than using the same sequence of random numbers after every +# reboot. This can be enabled with -e<entropy file> command line option. The +# specified file needs to be readable and writable by wpa_supplicant. +# +# If the os_get_random() is known to provide strong random data (e.g., on +# Linux/BSD, the board in question is known to have reliable source of random +# data from /dev/urandom), the internal wpa_supplicant random pool can be +# disabled. This will save some in binary size and CPU use. However, this +# should only be considered for builds that are known to be used on devices +# that meet the requirements described above. +#CONFIG_NO_RANDOM_POOL=y + +# IEEE 802.11n (High Throughput) support (mainly for AP mode) +#CONFIG_IEEE80211N=y + +# Wireless Network Management (IEEE Std 802.11v-2011) +# Note: This is experimental and not complete implementation. +#CONFIG_WNM=y + +# Interworking (IEEE 802.11u) +# This can be used to enable functionality to improve interworking with +# external networks (GAS/ANQP to learn more about the networks and network +# selection based on available credentials). +#CONFIG_INTERWORKING=y + +# Hotspot 2.0 +#CONFIG_HS20=y + +# AP mode operations with wpa_supplicant +# This can be used for controlling AP mode operations with wpa_supplicant. It +# should be noted that this is mainly aimed at simple cases like +# WPA2-Personal while more complex configurations like WPA2-Enterprise with an +# external RADIUS server can be supported with hostapd. +#CONFIG_AP=y + +# P2P (Wi-Fi Direct) +# This can be used to enable P2P support in wpa_supplicant. See README-P2P for +# more information on P2P operations. +#CONFIG_P2P=y + +# Autoscan +# This can be used to enable automatic scan support in wpa_supplicant. +# See wpa_supplicant.conf for more information on autoscan usage. +# +# Enabling directly a module will enable autoscan support. +# For exponential module: +#CONFIG_AUTOSCAN_EXPONENTIAL=y +# For periodic module: +#CONFIG_AUTOSCAN_PERIODIC=y + +# Password (and passphrase, etc.) backend for external storage +# These optional mechanisms can be used to add support for storing passwords +# and other secrets in external (to wpa_supplicant) location. This allows, for +# example, operating system specific key storage to be used +# +# External password backend for testing purposes (developer use) +#CONFIG_EXT_PASSWORD_TEST=y |
