diff options
-rw-r--r-- | share/man/man4/Makefile | 1 | ||||
-rw-r--r-- | share/man/man4/ucom.4 | 1 | ||||
-rw-r--r-- | share/man/man4/umcs7840.4 | 97 | ||||
-rw-r--r-- | sys/conf/files | 3 | ||||
-rw-r--r-- | sys/dev/usb/serial/umcs7840.c | 1075 | ||||
-rw-r--r-- | sys/dev/usb/serial/umcs7840.h | 644 | ||||
-rw-r--r-- | sys/dev/usb/usb_process.c | 7 | ||||
-rw-r--r-- | sys/dev/usb/usbdevs | 2 | ||||
-rw-r--r-- | sys/modules/usb/Makefile | 2 | ||||
-rw-r--r-- | sys/modules/usb/umcs7840/Makefile | 36 |
10 files changed, 1865 insertions, 3 deletions
diff --git a/share/man/man4/Makefile b/share/man/man4/Makefile index 47ffd55..a94d828 100644 --- a/share/man/man4/Makefile +++ b/share/man/man4/Makefile @@ -475,6 +475,7 @@ MAN= aac.4 \ ukbd.4 \ ulpt.4 \ umass.4 \ + umcs7840.4 \ umct.4 \ umodem.4 \ ums.4 \ diff --git a/share/man/man4/ucom.4 b/share/man/man4/ucom.4 index ff891cb..ee9c517 100644 --- a/share/man/man4/ucom.4 +++ b/share/man/man4/ucom.4 @@ -78,6 +78,7 @@ multiple external ports. .Xr uark 4 , .Xr uchcom 4 , .Xr uftdi 4 , +.Xr umcs7840 4 , .Xr umct 4 , .Xr umodem 4 , .Xr uplcom 4 , diff --git a/share/man/man4/umcs7840.4 b/share/man/man4/umcs7840.4 new file mode 100644 index 0000000..4b3ef5e --- /dev/null +++ b/share/man/man4/umcs7840.4 @@ -0,0 +1,97 @@ +.\" +.\" Copyright (c) 2010 Lev Serebryakov <lev@FreeBSD.org>. +.\" All rights reserved. +.\" +.\" This code is derived from software contributed to The NetBSD Foundation +.\" by Lennart Augustsson. +.\" +.\" Redistribution and use in source and binary forms, with or without +.\" modification, are permitted provided that the following conditions +.\" are met: +.\" 1. Redistributions of source code must retain the above copyright +.\" notice, this list of conditions and the following disclaimer. +.\" 2. Redistributions in binary form must reproduce the above copyright +.\" notice, this list of conditions and the following disclaimer in the +.\" documentation and/or other materials provided with the distribution. +.\" +.\" THIS SOFTWARE IS PROVIDED BY THE NETBSD FOUNDATION, INC. AND CONTRIBUTORS +.\" ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED +.\" TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR +.\" PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE FOUNDATION OR CONTRIBUTORS +.\" BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR +.\" CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF +.\" SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS +.\" INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN +.\" CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) +.\" ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE +.\" POSSIBILITY OF SUCH DAMAGE. +.\" +.\" $FreeBSD$ +.\" +.Dd December 10, 2010 +.Dt UMCS7840 4 +.Os +.Sh NAME +.Nm umcs7840 +.Nd USB support for serial adapters based on the MCS7820 and MCS7840 chips +.Sh SYNOPSIS +To compile this driver into the kernel, +place the following lines in your +kernel configuration file: +.Bd -ragged -offset indent +.Cd "device umcs7840" +.Ed +.Pp +Alternatively, to load the driver as a +module at boot time, place the following line in +.Xr loader.conf 5 : +.Bd -literal -offset indent +umcs7840_load="YES" +.Ed +.Sh DESCRIPTION +The +.Nm +driver provides support for various multiport serial adapters based on the MosCom +MCS7820 and MCS7840 chips. They are 2- or 4-port adapters with full-featured +16550-compatible UARTs and very flexible baud generators. Also, these chips +support RS422/RS485 and IrDA oprations. +.Pp +The device is accessed through the +.Xr ucom 4 +driver which makes it behave like a +.Xr tty 4 . +.Pp +Different ports on device are presented as sub-units, like +.Pa /dev/ttyU0.1 +and +.Pa /dev/ttyU0.2 +.Sh HARDWARE +The +.Nm +driver was tested on the following adapters: +.Pp +.Bl -bullet -compact +.It +ST Lab U-360 two-port serial USB adapter +.It +ST Lab U-400 four-port serial USB adapter +.El +.Sh SEE ALSO +.Xr tty 4 , +.Xr ucom 4 , +.Xr usb 4 +.Sh BUGS +This driver doesn't support access to any fine tunes of +chip, like RS522/RS485 mode, non-standard baudrates, etc. +.Sh HISTORY +The +.Nm +driver +appeared in ports since December of 2010. +.Sh AUTHORS +.An -nosplit +The +.Nm +driver was written by +.An Lev Serebryakov +.Aq lev@FreeBSD.org . diff --git a/sys/conf/files b/sys/conf/files index 82f633d..d75a2b8 100644 --- a/sys/conf/files +++ b/sys/conf/files @@ -1955,6 +1955,7 @@ dev/usb/serial/uftdi.c optional uftdi dev/usb/serial/ugensa.c optional ugensa dev/usb/serial/uipaq.c optional uipaq dev/usb/serial/ulpt.c optional ulpt +dev/usb/serial/umcs7840.c optional umcs7840 dev/usb/serial/umct.c optional umct dev/usb/serial/umodem.c optional umodem dev/usb/serial/umoscom.c optional umoscom @@ -1964,7 +1965,7 @@ dev/usb/serial/uvisor.c optional uvisor dev/usb/serial/uvscom.c optional uvscom dev/usb/serial/usb_serial.c optional ucom | u3g | uark | ubsa | ubser | \ uchcom | ucycom | ufoma | uftdi | \ - ugensa | uipaq | umct | \ + ugensa | uipaq | umcs7840 | umct | \ umodem | umoscom | uplcom | uslcom | \ uvisor | uvscom # diff --git a/sys/dev/usb/serial/umcs7840.c b/sys/dev/usb/serial/umcs7840.c new file mode 100644 index 0000000..34b68a1 --- /dev/null +++ b/sys/dev/usb/serial/umcs7840.c @@ -0,0 +1,1075 @@ +/*- + * Copyright (c) 2010 Lev Serebryakov <lev@FreeBSD.org>. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + */ + +/* + * This driver supports several multiport USB-to-RS232 serial adapters driven + * by MosChip mos7820 and mos7840, bridge chips. + * The adapters are sold under many different brand names. + * + * Datasheets are available at MosChip www site at + * http://www.moschip.com. The datasheets don't contain full + * programming information for the chip. + * + * It is nornal to have only two enabled ports in devices, based on + * quad-port mos7840. + * + */ +#include <sys/cdefs.h> +__FBSDID("$FreeBSD$"); + +#include <sys/stdint.h> +#include <sys/stddef.h> +#include <sys/param.h> +#include <sys/queue.h> +#include <sys/types.h> +#include <sys/systm.h> +#include <sys/kernel.h> +#include <sys/bus.h> +#include <sys/linker_set.h> +#include <sys/module.h> +#include <sys/lock.h> +#include <sys/mutex.h> +#include <sys/condvar.h> +#include <sys/sysctl.h> +#include <sys/sx.h> +#include <sys/unistd.h> +#include <sys/callout.h> +#include <sys/malloc.h> +#include <sys/priv.h> + +#include <dev/usb/usb.h> +#include <dev/usb/usbdi.h> +#include <dev/usb/usbdi_util.h> +#include <dev/usb/usb_cdc.h> +#include "usbdevs.h" + +#define USB_DEBUG_VAR umcs7840_debug +#include <dev/usb/usb_debug.h> +#include <dev/usb/usb_process.h> + +#include <dev/usb/serial/usb_serial.h> + +#include <dev/usb/serial/umcs7840.h> + +#define UMCS7840_MODVER 1 + +#ifdef USB_DEBUG +static int umcs7840_debug = 0; + +SYSCTL_NODE(_hw_usb, OID_AUTO, umcs7840, CTLFLAG_RW, 0, "USB umcs7840 quadport serial adapter"); +SYSCTL_INT(_hw_usb_umcs7840, OID_AUTO, debug, CTLFLAG_RW, &umcs7840_debug, 0, "Debug level"); +#endif /* USB_DEBUG */ + + +/* + * Two-port devices (both with 7820 chip and 7840 chip configured as two-port) + * have ports 0 and 2, with ports 1 and 3 omitted. + * So,PHYSICAL port numbers (indexes) on two-port device will be 0 and 2. + * This driver trys to use physical numbers as much as possible. + */ + +/* + * Indexed by PHYSICAL port number. + * Pack non-regular registers to array to easier if-less access. + */ +struct umcs7840_port_registers { + uint8_t reg_sp; /* SP register. */ + uint8_t reg_control; /* CONTROL register. */ + uint8_t reg_dcr; /* DCR0 register. DCR1 & DCR2 can be + * calculated */ +}; + +static const struct umcs7840_port_registers umcs7840_port_registers[UMCS7840_MAX_PORTS] = { + {.reg_sp = MCS7840_DEV_REG_SP1,.reg_control = MCS7840_DEV_REG_CONTROL1,.reg_dcr = MCS7840_DEV_REG_DCR0_1}, + {.reg_sp = MCS7840_DEV_REG_SP2,.reg_control = MCS7840_DEV_REG_CONTROL2,.reg_dcr = MCS7840_DEV_REG_DCR0_2}, + {.reg_sp = MCS7840_DEV_REG_SP3,.reg_control = MCS7840_DEV_REG_CONTROL3,.reg_dcr = MCS7840_DEV_REG_DCR0_3}, + {.reg_sp = MCS7840_DEV_REG_SP4,.reg_control = MCS7840_DEV_REG_CONTROL4,.reg_dcr = MCS7840_DEV_REG_DCR0_4}, +}; + +enum { + UMCS7840_BULK_RD_EP, + UMCS7840_BULK_WR_EP, + UMCS7840_N_TRANSFERS +}; + +struct umcs7840_softc_oneport { + struct usb_xfer *sc_xfer[UMCS7840_N_TRANSFERS]; /* Control structures + * for two transfers */ + + uint8_t sc_lcr; /* local line control register */ + uint8_t sc_mcr; /* local modem control register */ + uint8_t sc_lsr; /* local line status register */ + uint8_t sc_msr; /* local modem status register */ +}; + +struct umcs7840_softc { + struct ucom_super_softc sc_super_ucom; + struct ucom_softc sc_ucom[UMCS7840_MAX_PORTS]; /* Need to be continuous + * array, so indexed by + * LOGICAL port + * (subunit) number */ + + struct usb_xfer *sc_intr_xfer; /* Interrupt endpoint */ + + device_t sc_dev; /* Device for error prints */ + struct usb_device *sc_udev; /* USB Device for all operations */ + struct mtx sc_mtx; /* ucom requires this */ + + uint8_t sc_driver_done; /* Flag when enumeration is finished */ + + uint8_t sc_numports; /* Number of ports (subunits) */ + struct umcs7840_softc_oneport sc_ports[UMCS7840_MAX_PORTS]; /* Indexed by PHYSICAL + * port number. */ +}; + +/* prototypes */ +static usb_error_t umcs7840_get_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t *); +static usb_error_t umcs7840_set_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t); +static usb_error_t umcs7840_get_UART_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t, uint8_t *); +static usb_error_t umcs7840_set_UART_reg_sync(struct umcs7840_softc *, uint8_t, uint8_t, uint8_t); + +static usb_error_t umcs7840_set_baudrate(struct umcs7840_softc *, uint8_t, uint32_t); +static usb_error_t umcs7840_calc_baudrate(uint32_t rate, uint16_t *, uint8_t *); + +static void umcs7840_cfg_get_status(struct ucom_softc *, uint8_t *, uint8_t *); +static void umcs7840_cfg_set_dtr(struct ucom_softc *, uint8_t); +static void umcs7840_cfg_set_rts(struct ucom_softc *, uint8_t); +static void umcs7840_cfg_set_break(struct ucom_softc *, uint8_t); +static void umcs7840_cfg_param(struct ucom_softc *, struct termios *); +static void umcs7840_cfg_open(struct ucom_softc *); +static void umcs7840_cfg_close(struct ucom_softc *); + +static int umcs7840_pre_param(struct ucom_softc *, struct termios *); + +static void umcs7840_start_read(struct ucom_softc *); +static void umcs7840_stop_read(struct ucom_softc *); + +static void umcs7840_start_write(struct ucom_softc *); +static void umcs7840_stop_write(struct ucom_softc *); + +static void umcs7840_poll(struct ucom_softc *ucom); + +static device_probe_t umcs7840_probe; +static device_attach_t umcs7840_attach; +static device_detach_t umcs7840_detach; + +static usb_callback_t umcs7840_intr_callback; +static usb_callback_t umcs7840_read_callback1; +static usb_callback_t umcs7840_read_callback2; +static usb_callback_t umcs7840_read_callback3; +static usb_callback_t umcs7840_read_callback4; +static usb_callback_t umcs7840_write_callback1; +static usb_callback_t umcs7840_write_callback2; +static usb_callback_t umcs7840_write_callback3; +static usb_callback_t umcs7840_write_callback4; + +static void umcs7840_read_callbackN(struct usb_xfer *, usb_error_t, uint8_t); +static void umcs7840_write_callbackN(struct usb_xfer *, usb_error_t, uint8_t); + +/* Indexed by LOGICAL port number (subunit), so two-port device uses 0 & 1 */ +static usb_callback_t *umcs7840_rw_callbacks[UMCS7840_MAX_PORTS][UMCS7840_N_TRANSFERS] = { + {&umcs7840_read_callback1, &umcs7840_write_callback1}, + {&umcs7840_read_callback2, &umcs7840_write_callback2}, + {&umcs7840_read_callback3, &umcs7840_write_callback3}, + {&umcs7840_read_callback4, &umcs7840_write_callback4}, +}; + +static const struct usb_config umcs7840_bulk_config_data[UMCS7840_N_TRANSFERS] = { + [UMCS7840_BULK_RD_EP] = { + .type = UE_BULK, + .endpoint = 0x01, + .direction = UE_DIR_IN, + .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, + .bufsize = 0, /* use wMaxPacketSize */ + .callback = &umcs7840_read_callback1, + .if_index = 0, + }, + + [UMCS7840_BULK_WR_EP] = { + .type = UE_BULK, + .endpoint = 0x02, + .direction = UE_DIR_OUT, + .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, + .bufsize = 0, /* use wMaxPacketSize */ + .callback = &umcs7840_write_callback1, + .if_index = 0, + }, +}; + +static const struct usb_config umcs7840_intr_config_data[1] = { + [0] = { + .type = UE_INTERRUPT, + .endpoint = 0x09, + .direction = UE_DIR_IN, + .flags = {.pipe_bof = 1,.short_xfer_ok = 1,}, + .bufsize = 0, /* use wMaxPacketSize */ + .callback = &umcs7840_intr_callback, + .if_index = 0, + }, +}; + +static struct ucom_callback umcs7840_callback = { + .ucom_cfg_get_status = &umcs7840_cfg_get_status, + + .ucom_cfg_set_dtr = &umcs7840_cfg_set_dtr, + .ucom_cfg_set_rts = &umcs7840_cfg_set_rts, + .ucom_cfg_set_break = &umcs7840_cfg_set_break, + + .ucom_cfg_param = &umcs7840_cfg_param, + .ucom_cfg_open = &umcs7840_cfg_open, + .ucom_cfg_close = &umcs7840_cfg_close, + + .ucom_pre_param = &umcs7840_pre_param, + + .ucom_start_read = &umcs7840_start_read, + .ucom_stop_read = &umcs7840_stop_read, + + .ucom_start_write = &umcs7840_start_write, + .ucom_stop_write = &umcs7840_stop_write, + + .ucom_poll = &umcs7840_poll, +}; + +static const struct usb_device_id umcs7840_devs[] = { + {USB_VPI(USB_VENDOR_MOSCHIP, USB_PRODUCT_MOSCHIP_MCS7820, 0)}, + {USB_VPI(USB_VENDOR_MOSCHIP, USB_PRODUCT_MOSCHIP_MCS7840, 0)}, +}; + +static device_method_t umcs7840_methods[] = { + DEVMETHOD(device_probe, umcs7840_probe), + DEVMETHOD(device_attach, umcs7840_attach), + DEVMETHOD(device_detach, umcs7840_detach), + {0, 0} +}; + +static devclass_t umcs7840_devclass; + +static driver_t umcs7840_driver = { + .name = "umcs7840", + .methods = umcs7840_methods, + .size = sizeof(struct umcs7840_softc), +}; + +DRIVER_MODULE(umcs7840, uhub, umcs7840_driver, umcs7840_devclass, 0, 0); +MODULE_DEPEND(umcs7840, ucom, 1, 1, 1); +MODULE_DEPEND(umcs7840, usb, 1, 1, 1); +MODULE_VERSION(umcs7840, UMCS7840_MODVER); + +static int +umcs7840_probe(device_t dev) +{ + struct usb_attach_arg *uaa = device_get_ivars(dev); + + if (uaa->usb_mode != USB_MODE_HOST) + return (ENXIO); + if (uaa->info.bConfigIndex != MCS7840_CONFIG_INDEX) + return (ENXIO); + if (uaa->info.bIfaceIndex != MCS7840_IFACE_INDEX) + return (ENXIO); + return (usbd_lookup_id_by_uaa(umcs7840_devs, sizeof(umcs7840_devs), uaa)); +} + +static int +umcs7840_attach(device_t dev) +{ + struct usb_config umcs7840_config_tmp[UMCS7840_N_TRANSFERS]; + struct usb_attach_arg *uaa = device_get_ivars(dev); + struct umcs7840_softc *sc = device_get_softc(dev); + + uint8_t iface_index = MCS7840_IFACE_INDEX; + int error; + int subunit; + int n; + uint8_t data; + + for (n = 0; n < UMCS7840_N_TRANSFERS; ++n) + umcs7840_config_tmp[n] = umcs7840_bulk_config_data[n]; + + device_set_usb_desc(dev); + mtx_init(&sc->sc_mtx, "umcs7840", NULL, MTX_DEF); + + sc->sc_dev = dev; + sc->sc_udev = uaa->device; + + /* + * Get number of ports + * Documentation (full datasheet) says, that number of ports is + * set as MCS7840_DEV_MODE_SELECT24S bit in MODE R/Only + * register. But vendor driver uses these undocumented + * register & bit. + * + * Experiments show, that MODE register can have `0' + * (4 ports) bit on 2-port device, so use vendor driver's way. + * + * Also, see notes in header file for these constants. + */ + umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_GPIO, &data); + if (data & MCS7840_DEV_GPIO_4PORTS) { + sc->sc_numports = 4; + /* Store physical port numbers in sc_portno */ + sc->sc_ucom[0].sc_portno = 0; + sc->sc_ucom[1].sc_portno = 1; + sc->sc_ucom[2].sc_portno = 2; + sc->sc_ucom[3].sc_portno = 3; + } else { + sc->sc_numports = 2; + /* Store physical port numbers in sc_portno */ + sc->sc_ucom[0].sc_portno = 0; + sc->sc_ucom[1].sc_portno = 2; /* '1' is skipped */ + } + device_printf(dev, "Chip mcs%04x, found %d active ports\n", uaa->info.idProduct, sc->sc_numports); + if (!umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_MODE, &data)) { + device_printf(dev, "On-die confguration: RST: active %s, HRD: %s, PLL: %s, POR: %s, Ports: %s, EEPROM write %s, IrDA is %savailable\n", + (data & MCS7840_DEV_MODE_RESET) ? "low" : "high", + (data & MCS7840_DEV_MODE_SER_PRSNT) ? "yes" : "no", + (data & MCS7840_DEV_MODE_PLLBYPASS) ? "bypassed" : "avail", + (data & MCS7840_DEV_MODE_PORBYPASS) ? "bypassed" : "avail", + (data & MCS7840_DEV_MODE_SELECT24S) ? "2" : "4", + (data & MCS7840_DEV_MODE_EEPROMWR) ? "enabled" : "disabled", + (data & MCS7840_DEV_MODE_IRDA) ? "" : "not "); + } + /* Setup all transfers */ + for (subunit = 0; subunit < sc->sc_numports; ++subunit) { + for (n = 0; n < UMCS7840_N_TRANSFERS; ++n) { + /* Set endpoint address */ + umcs7840_config_tmp[n].endpoint = umcs7840_bulk_config_data[n].endpoint + 2 * sc->sc_ucom[subunit].sc_portno; + umcs7840_config_tmp[n].callback = umcs7840_rw_callbacks[subunit][n]; + } + error = usbd_transfer_setup(uaa->device, + &iface_index, sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer, umcs7840_config_tmp, + UMCS7840_N_TRANSFERS, sc, &sc->sc_mtx); + if (error) { + device_printf(dev, "allocating USB transfers failed for subunit %d of %d\n", + subunit + 1, sc->sc_numports); + goto detach; + } + } + error = usbd_transfer_setup(uaa->device, + &iface_index, &sc->sc_intr_xfer, umcs7840_intr_config_data, + 1, sc, &sc->sc_mtx); + if (error) { + device_printf(dev, "allocating USB transfers failed for interrupt\n"); + goto detach; + } + /* clear stall at first run */ + mtx_lock(&sc->sc_mtx); + for (subunit = 0; subunit < sc->sc_numports; ++subunit) { + usbd_xfer_set_stall(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer[UMCS7840_BULK_RD_EP]); + usbd_xfer_set_stall(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer[UMCS7840_BULK_WR_EP]); + } + mtx_unlock(&sc->sc_mtx); + + error = ucom_attach(&sc->sc_super_ucom, sc->sc_ucom, sc->sc_numports, sc, + &umcs7840_callback, &sc->sc_mtx); + if (error) + goto detach; + + ucom_set_pnpinfo_usb(&sc->sc_super_ucom, dev); + + return (0); + +detach: + umcs7840_detach(dev); + return (ENXIO); +} + +static int +umcs7840_detach(device_t dev) +{ + struct umcs7840_softc *sc = device_get_softc(dev); + int subunit; + + ucom_detach(&sc->sc_super_ucom, sc->sc_ucom); + + for (subunit = 0; subunit < sc->sc_numports; ++subunit) + usbd_transfer_unsetup(sc->sc_ports[sc->sc_ucom[subunit].sc_portno].sc_xfer, UMCS7840_N_TRANSFERS); + usbd_transfer_unsetup(&sc->sc_intr_xfer, 1); + + mtx_destroy(&sc->sc_mtx); + return (0); +} + +static void +umcs7840_cfg_open(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint16_t pn = ucom->sc_portno; + uint8_t data; + + /* If it very first open, finish global configuration */ + if (!sc->sc_driver_done) { + /* + * USB enumeration is finished, pass internal memory to FIFOs + * If it is done in the end of "attach", kernel panics. + */ + if (umcs7840_get_reg_sync(sc, MCS7840_DEV_REG_CONTROL1, &data)) + return; + data |= MCS7840_DEV_CONTROL1_DRIVER_DONE; + if (umcs7840_set_reg_sync(sc, MCS7840_DEV_REG_CONTROL1, data)) + return; + sc->sc_driver_done = 1; + } + /* Toggle reset bit on-off */ + if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, &data)) + return; + data |= MCS7840_DEV_SPx_UART_RESET; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) + return; + data &= ~MCS7840_DEV_SPx_UART_RESET; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) + return; + + /* Set RS-232 mode */ + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_SCRATCHPAD, MCS7840_UART_SCRATCHPAD_RS232)) + return; + + /* Disable RX on time of initialization */ + if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) + return; + data |= MCS7840_DEV_CONTROLx_RX_DISABLE; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) + return; + + /* Disable all interrupts */ + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, 0)) + return; + + /* Reset FIFO -- documented */ + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_FCR, 0)) + return; + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_FCR, + MCS7840_UART_FCR_ENABLE | MCS7840_UART_FCR_FLUSHRHR | + MCS7840_UART_FCR_FLUSHTHR | MCS7840_UART_FCR_RTL_1_14)) + return; + + /* Set 8 bit, no parity, 1 stop bit -- documented */ + sc->sc_ports[pn].sc_lcr = MCS7840_UART_LCR_DATALEN8 | MCS7840_UART_LCR_STOPB1; + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr)) + return; + + /* + * Enable DTR/RTS on modem control, enable modem interrupts -- + * documented + */ + sc->sc_ports[pn].sc_mcr = MCS7840_UART_MCR_DTR | MCS7840_UART_MCR_RTS | MCS7840_UART_MCR_IE; + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr)) + return; + + /* Clearing Bulkin and Bulkout FIFO */ + if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, &data)) + return; + data |= MCS7840_DEV_SPx_RESET_OUT_FIFO | MCS7840_DEV_SPx_RESET_IN_FIFO; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) + return; + data &= ~(MCS7840_DEV_SPx_RESET_OUT_FIFO | MCS7840_DEV_SPx_RESET_IN_FIFO); + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_sp, data)) + return; + + /* Set speed 9600 */ + if (umcs7840_set_baudrate(sc, pn, 9600)) + return; + + + /* Finally enable all interrupts -- documented */ + /* + * Copied from vendor driver, I don't know why we should read LCR + * here + */ + if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, &sc->sc_ports[pn].sc_lcr)) + return; + if (umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, + MCS7840_UART_IER_RXSTAT | MCS7840_UART_IER_MODEM)) + return; + + /* Enable RX */ + if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) + return; + data &= ~MCS7840_DEV_CONTROLx_RX_DISABLE; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) + return; + + /* Read LSR & MSR */ + if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_LSR, &sc->sc_ports[pn].sc_lsr)) + return; + if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_MSR, &sc->sc_ports[pn].sc_msr)) + return; + DPRINTF("Port %d has been opened, LSR=%02x MSR=%02x\n", pn, sc->sc_ports[pn].sc_lsr, sc->sc_ports[pn].sc_msr); +} + +static void +umcs7840_cfg_close(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint16_t pn = ucom->sc_portno; + uint8_t data; + + umcs7840_stop_read(ucom); + umcs7840_stop_write(ucom); + + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, 0); + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_IER, 0); + + /* Disable RX */ + if (umcs7840_get_reg_sync(sc, umcs7840_port_registers[pn].reg_control, &data)) + return; + data |= MCS7840_DEV_CONTROLx_RX_DISABLE; + if (umcs7840_set_reg_sync(sc, umcs7840_port_registers[pn].reg_control, data)) + return; + DPRINTF("Port %d has been closed\n", pn); +} + +static void +umcs7840_cfg_set_dtr(struct ucom_softc *ucom, uint8_t onoff) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + if (onoff) + sc->sc_ports[pn].sc_mcr |= MCS7840_UART_MCR_DTR; + else + sc->sc_ports[pn].sc_mcr &= ~MCS7840_UART_MCR_DTR; + + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); + DPRINTF("Port %d DTR set to: %s\n", pn, onoff ? "on" : "off"); +} + +static void +umcs7840_cfg_set_rts(struct ucom_softc *ucom, uint8_t onoff) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + if (onoff) + sc->sc_ports[pn].sc_mcr |= MCS7840_UART_MCR_RTS; + else + sc->sc_ports[pn].sc_mcr &= ~MCS7840_UART_MCR_RTS; + + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); + DPRINTF("Port %d RTS set to: %s\n", pn, onoff ? "on" : "off"); +} + +static void +umcs7840_cfg_set_break(struct ucom_softc *ucom, uint8_t onoff) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + if (onoff) + sc->sc_ports[pn].sc_lcr |= MCS7840_UART_LCR_BREAK; + else + sc->sc_ports[pn].sc_lcr &= ~MCS7840_UART_LCR_BREAK; + + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr); + DPRINTF("Port %d BREAK set to: %s\n", pn, onoff ? "on" : "off"); +} + + +static void +umcs7840_cfg_param(struct ucom_softc *ucom, struct termios *t) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + uint8_t lcr = sc->sc_ports[pn].sc_lcr; + uint8_t mcr = sc->sc_ports[pn].sc_mcr; + + DPRINTF("Port %d config:\n", pn); + if (t->c_cflag & CSTOPB) { + DPRINTF(" 2 stop bits\n"); + lcr |= MCS7840_UART_LCR_STOPB2; + } else { + lcr |= MCS7840_UART_LCR_STOPB1; + DPRINTF(" 1 stop bit\n"); + } + + lcr &= ~MCS7840_UART_LCR_PARITYMASK; + if (t->c_cflag & PARENB) { + lcr |= MCS7840_UART_LCR_PARITYON; + if (t->c_cflag & PARODD) { + lcr = MCS7840_UART_LCR_PARITYODD; + DPRINTF(" parity on - odd\n"); + } else { + lcr = MCS7840_UART_LCR_PARITYEVEN; + DPRINTF(" parity on - even\n"); + } + } else { + lcr &= ~MCS7840_UART_LCR_PARITYON; + DPRINTF(" parity off\n"); + } + + lcr &= ~MCS7840_UART_LCR_DATALENMASK; + switch (t->c_cflag & CSIZE) { + case CS5: + lcr |= MCS7840_UART_LCR_DATALEN5; + DPRINTF(" 5 bit\n"); + break; + case CS6: + lcr |= MCS7840_UART_LCR_DATALEN6; + DPRINTF(" 6 bit\n"); + break; + case CS7: + lcr |= MCS7840_UART_LCR_DATALEN7; + DPRINTF(" 7 bit\n"); + break; + case CS8: + lcr |= MCS7840_UART_LCR_DATALEN8; + DPRINTF(" 8 bit\n"); + break; + } + + if (t->c_cflag & CRTSCTS) { + mcr |= MCS7840_UART_MCR_CTSRTS; + DPRINTF(" CTS/RTS\n"); + } else + mcr &= ~MCS7840_UART_MCR_CTSRTS; + + if (t->c_cflag & (CDTR_IFLOW | CDSR_OFLOW)) { + mcr |= MCS7840_UART_MCR_DTRDSR; + DPRINTF(" DTR/DSR\n"); + } else + mcr &= ~MCS7840_UART_MCR_DTRDSR; + + sc->sc_ports[pn].sc_lcr = lcr; + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_LCR, sc->sc_ports[pn].sc_lcr); + DPRINTF("Port %d LCR=%02x\n", pn, sc->sc_ports[pn].sc_lcr); + + sc->sc_ports[pn].sc_mcr = mcr; + umcs7840_set_UART_reg_sync(sc, pn, MCS7840_UART_REG_MCR, sc->sc_ports[pn].sc_mcr); + DPRINTF("Port %d MCR=%02x\n", pn, sc->sc_ports[pn].sc_mcr); + + umcs7840_set_baudrate(sc, pn, t->c_ospeed); +} + + +static int +umcs7840_pre_param(struct ucom_softc *ucom, struct termios *t) +{ + uint8_t clk; + uint16_t divisor; + + if (umcs7840_calc_baudrate(t->c_ospeed, &divisor, &clk) || !divisor) + return (EINVAL); + return (0); +} + +static void +umcs7840_start_read(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + /* Start interrupt transfer */ + usbd_transfer_start(sc->sc_intr_xfer); + + /* Start read transfer */ + usbd_transfer_start(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_RD_EP]); +} + +static void +umcs7840_stop_read(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + /* Stop read transfer */ + usbd_transfer_stop(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_RD_EP]); +} + +static void +umcs7840_start_write(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + /* Start interrupt transfer */ + usbd_transfer_start(sc->sc_intr_xfer); + + /* Start write transfer */ + usbd_transfer_start(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_WR_EP]); +} + +static void +umcs7840_stop_write(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + uint8_t pn = ucom->sc_portno; + + /* Stop write transfer */ + usbd_transfer_stop(sc->sc_ports[pn].sc_xfer[UMCS7840_BULK_WR_EP]); +} + +static void +umcs7840_cfg_get_status(struct ucom_softc *ucom, uint8_t *lsr, uint8_t *msr) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + + *lsr = sc->sc_ports[ucom->sc_portno].sc_lsr; + *msr = sc->sc_ports[ucom->sc_portno].sc_msr; + DPRINTF("Port %d status: LSR=%02x MSR=%02x\n", ucom->sc_portno, *lsr, *msr); +} + +static void +umcs7840_intr_callback(struct usb_xfer *xfer, usb_error_t error) +{ + struct umcs7840_softc *sc = usbd_xfer_softc(xfer); + struct usb_page_cache *pc; + uint8_t buf[13]; + int actlen; + int subunit; + + usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); + + switch (USB_GET_STATE(xfer)) { + case USB_ST_TRANSFERRED: + if (actlen == 5 || actlen == 13) { + pc = usbd_xfer_get_frame(xfer, 0); + usbd_copy_out(pc, 0, buf, actlen); + /* Check status of all ports */ + for (subunit = 0; subunit < sc->sc_numports; ++subunit) { + uint8_t pn = sc->sc_ucom[subunit].sc_portno; + + if (buf[pn] & MCS7840_UART_ISR_NOPENDING) + continue; + DPRINTF("Port %d has pending interrupt: %02x (FIFO: %02x)\n", pn, buf[pn] & MCS7840_UART_ISR_INTMASK, buf[pn] & (~MCS7840_UART_ISR_INTMASK)); + switch (buf[pn] & MCS7840_UART_ISR_INTMASK) { + case MCS7840_UART_ISR_RXERR: + case MCS7840_UART_ISR_RXHASDATA: + case MCS7840_UART_ISR_RXTIMEOUT: + /* Read new LSR */ + if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_LSR, &sc->sc_ports[pn].sc_lsr)) + break; /* Inner switch */ + ucom_status_change(&sc->sc_ucom[subunit]); + /* Inner switch */ + break; + case MCS7840_UART_ISR_TXEMPTY: + /* Do nothing */ + break; /* Inner switch */ + case MCS7840_UART_ISR_MSCHANGE: + /* Read new MSR */ + if (umcs7840_get_UART_reg_sync(sc, pn, MCS7840_UART_REG_MSR, &sc->sc_ports[pn].sc_msr)) + break; /* Inner switch */ + DPRINTF("Port %d: new MSR %02x\n", pn, sc->sc_ports[pn].sc_msr); + ucom_status_change(&sc->sc_ucom[subunit]); + break; + } + } + } else + device_printf(sc->sc_dev, "Invalid interrupt data length %d", actlen); + /* FALLTHROUGH */ + case USB_ST_SETUP: +tr_setup: + usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); + usbd_transfer_submit(xfer); + return; + + default: /* Error */ + if (error != USB_ERR_CANCELLED) { + /* try to clear stall first */ + usbd_xfer_set_stall(xfer); + goto tr_setup; + } + return; + } +} + +static void +umcs7840_read_callback1(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_read_callbackN(xfer, error, 0); +} + +static void +umcs7840_read_callback2(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_read_callbackN(xfer, error, 1); +} +static void +umcs7840_read_callback3(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_read_callbackN(xfer, error, 2); +} + +static void +umcs7840_read_callback4(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_read_callbackN(xfer, error, 3); +} + +static void +umcs7840_read_callbackN(struct usb_xfer *xfer, usb_error_t error, uint8_t subunit) +{ + struct umcs7840_softc *sc = usbd_xfer_softc(xfer); + struct ucom_softc *ucom = &sc->sc_ucom[subunit]; + struct usb_page_cache *pc; + int actlen; + + usbd_xfer_status(xfer, &actlen, NULL, NULL, NULL); + + DPRINTF("Port %d read, state = %d, data length = %d\n", ucom->sc_portno, USB_GET_STATE(xfer), actlen); + + switch (USB_GET_STATE(xfer)) { + case USB_ST_TRANSFERRED: + pc = usbd_xfer_get_frame(xfer, 0); + ucom_put_data(ucom, pc, 0, actlen); + /* FALLTHROUGH */ + case USB_ST_SETUP: +tr_setup: + usbd_xfer_set_frame_len(xfer, 0, usbd_xfer_max_len(xfer)); + usbd_transfer_submit(xfer); + return; + + default: /* Error */ + if (error != USB_ERR_CANCELLED) { + /* try to clear stall first */ + usbd_xfer_set_stall(xfer); + goto tr_setup; + } + return; + } +} + +static void +umcs7840_write_callback1(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_write_callbackN(xfer, error, 0); +} + +static void +umcs7840_write_callback2(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_write_callbackN(xfer, error, 1); +} + +static void +umcs7840_write_callback3(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_write_callbackN(xfer, error, 2); +} + +static void +umcs7840_write_callback4(struct usb_xfer *xfer, usb_error_t error) +{ + umcs7840_write_callbackN(xfer, error, 3); +} + +static void +umcs7840_write_callbackN(struct usb_xfer *xfer, usb_error_t error, uint8_t subunit) +{ + struct umcs7840_softc *sc = usbd_xfer_softc(xfer); + struct ucom_softc *ucom = &sc->sc_ucom[subunit]; + struct usb_page_cache *pc; + uint32_t actlen; + + DPRINTF("Port %d write, state = %d\n", ucom->sc_portno, USB_GET_STATE(xfer)); + + switch (USB_GET_STATE(xfer)) { + case USB_ST_SETUP: + case USB_ST_TRANSFERRED: +tr_setup: + pc = usbd_xfer_get_frame(xfer, 0); + if (ucom_get_data(ucom, pc, 0, usbd_xfer_max_len(xfer), &actlen)) { + DPRINTF("Port %d write, has %d bytes\n", ucom->sc_portno, actlen); + usbd_xfer_set_frame_len(xfer, 0, actlen); + usbd_transfer_submit(xfer); + } + return; + + default: /* Error */ + if (error != USB_ERR_CANCELLED) { + /* try to clear stall first */ + usbd_xfer_set_stall(xfer); + goto tr_setup; + } + return; + } +} + +static void +umcs7840_poll(struct ucom_softc *ucom) +{ + struct umcs7840_softc *sc = ucom->sc_parent; + + DPRINTF("Port %d poll\n", ucom->sc_portno); + usbd_transfer_poll(sc->sc_ports[ucom->sc_portno].sc_xfer, UMCS7840_N_TRANSFERS); + usbd_transfer_poll(&sc->sc_intr_xfer, 1); +} + +static usb_error_t +umcs7840_get_reg_sync(struct umcs7840_softc *sc, uint8_t reg, uint8_t *data) +{ + struct usb_device_request req; + usb_error_t err; + uint16_t len; + + req.bmRequestType = UT_READ_VENDOR_DEVICE; + req.bRequest = MCS7840_RDREQ; + USETW(req.wValue, 0); + USETW(req.wIndex, reg); + USETW(req.wLength, UMCS7840_READ_LENGTH); + + err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, (void *)data, 0, &len, UMCS7840_CTRL_TIMEOUT); + if (err == USB_ERR_NORMAL_COMPLETION && len != 1) { + device_printf(sc->sc_dev, "Reading register %d failed: invalid length %d\n", reg, len); + return (USB_ERR_INVAL); + } else if (err) + device_printf(sc->sc_dev, "Reading register %d failed: %s\n", reg, usbd_errstr(err)); + return (err); +} + +static usb_error_t +umcs7840_set_reg_sync(struct umcs7840_softc *sc, uint8_t reg, uint8_t data) +{ + struct usb_device_request req; + usb_error_t err; + + req.bmRequestType = UT_WRITE_VENDOR_DEVICE; + req.bRequest = MCS7840_WRREQ; + USETW(req.wValue, data); + USETW(req.wIndex, reg); + USETW(req.wLength, 0); + + err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, NULL, 0, NULL, UMCS7840_CTRL_TIMEOUT); + if (err) + device_printf(sc->sc_dev, "Writing register %d failed: %s\n", reg, usbd_errstr(err)); + + return (err); +} + +static usb_error_t +umcs7840_get_UART_reg_sync(struct umcs7840_softc *sc, uint8_t portno, uint8_t reg, uint8_t *data) +{ + struct usb_device_request req; + uint16_t wVal; + usb_error_t err; + uint16_t len; + + /* portno is port number */ + wVal = ((uint16_t)(portno + 1)) << 8; + + req.bmRequestType = UT_READ_VENDOR_DEVICE; + req.bRequest = MCS7840_RDREQ; + USETW(req.wValue, wVal); + USETW(req.wIndex, reg); + USETW(req.wLength, UMCS7840_READ_LENGTH); + + err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, (void *)data, 0, &len, UMCS7840_CTRL_TIMEOUT); + if (err == USB_ERR_NORMAL_COMPLETION && len != 1) { + device_printf(sc->sc_dev, "Reading UART%d register %d failed: invalid length %d\n", portno, reg, len); + return (USB_ERR_INVAL); + } else if (err) + device_printf(sc->sc_dev, "Reading UART%d register %d failed: %s\n", portno, reg, usbd_errstr(err)); + return (err); +} + +static usb_error_t +umcs7840_set_UART_reg_sync(struct umcs7840_softc *sc, uint8_t portno, uint8_t reg, uint8_t data) +{ + struct usb_device_request req; + usb_error_t err; + uint16_t wVal; + + /* portno is port number */ + wVal = ((uint16_t)(portno + 1)) << 8 | data; + + req.bmRequestType = UT_WRITE_VENDOR_DEVICE; + req.bRequest = MCS7840_WRREQ; + USETW(req.wValue, wVal); + USETW(req.wIndex, reg); + USETW(req.wLength, 0); + + err = usbd_do_request_proc(sc->sc_udev, &sc->sc_super_ucom.sc_tq, &req, NULL, 0, NULL, UMCS7840_CTRL_TIMEOUT); + if (err) + device_printf(sc->sc_dev, "Writing UART%d register %d failed: %s\n", portno, reg, usbd_errstr(err)); + return (err); +} + +static usb_error_t +umcs7840_set_baudrate(struct umcs7840_softc *sc, uint8_t portno, uint32_t rate) +{ + usb_error_t err; + uint16_t divisor; + uint8_t clk; + uint8_t data; + + if (umcs7840_calc_baudrate(rate, &divisor, &clk)) { + DPRINTF("Port %d bad speed: %d\n", portno, rate); + return (-1); + } + if (divisor == 0 || (clk & MCS7840_DEV_SPx_CLOCK_MASK) != clk) { + DPRINTF("Port %d bad speed calculation: %d\n", portno, rate); + return (-1); + } + DPRINTF("Port %d set speed: %d (%02x / %d)\n", portno, rate, clk, divisor); + + /* Set clock source for standard BAUD frequences */ + err = umcs7840_get_reg_sync(sc, umcs7840_port_registers[portno].reg_sp, &data); + if (err) + return (err); + data &= MCS7840_DEV_SPx_CLOCK_MASK; + data |= clk; + err = umcs7840_set_reg_sync(sc, umcs7840_port_registers[portno].reg_sp, data); + if (err) + return (err); + + /* Set divider */ + sc->sc_ports[portno].sc_lcr |= MCS7840_UART_LCR_DIVISORS; + err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_LCR, sc->sc_ports[portno].sc_lcr); + if (err) + return (err); + + err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_DLL, (uint8_t)(divisor & 0xff)); + if (err) + return (err); + err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_DLM, (uint8_t)((divisor >> 8) & 0xff)); + if (err) + return (err); + + /* Turn off access to DLL/DLM registers of UART */ + sc->sc_ports[portno].sc_lcr &= ~MCS7840_UART_LCR_DIVISORS; + err = umcs7840_set_UART_reg_sync(sc, portno, MCS7840_UART_REG_LCR, sc->sc_ports[portno].sc_lcr); + if (err) + return (err); + return (0); +} + +/* Maximum speeds for standard frequences, when PLL is not used */ +static const uint32_t umcs7840_baudrate_divisors[] = {0, 115200, 230400, 403200, 460800, 806400, 921600, 1572864, 3145728,}; +static const uint8_t umcs7840_baudrate_divisors_len = sizeof(umcs7840_baudrate_divisors) / sizeof(umcs7840_baudrate_divisors[0]); + +static usb_error_t +umcs7840_calc_baudrate(uint32_t rate, uint16_t *divisor, uint8_t *clk) +{ + uint8_t i = 0; + + if (rate > umcs7840_baudrate_divisors[umcs7840_baudrate_divisors_len - 1]) + return (-1); + + for (i = 0; i < umcs7840_baudrate_divisors_len - 1 && + !(rate > umcs7840_baudrate_divisors[i] && rate <= umcs7840_baudrate_divisors[i + 1]); ++i); + *divisor = umcs7840_baudrate_divisors[i + 1] / rate; + /* 0x00 .. 0x70 */ + *clk = i << MCS7840_DEV_SPx_CLOCK_SHIFT; + return (0); +} diff --git a/sys/dev/usb/serial/umcs7840.h b/sys/dev/usb/serial/umcs7840.h new file mode 100644 index 0000000..310b4af --- /dev/null +++ b/sys/dev/usb/serial/umcs7840.h @@ -0,0 +1,644 @@ +/* $FreeBSD$ */ +/*- + * Copyright (c) 2010 Lev Serebryakov <lev@FreeBSD.org>. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND + * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE + * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT + * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY + * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF + * SUCH DAMAGE. + */ +#ifndef _UMCS7840_H_ +#define _UMCS7840_H_ + +#define UMCS7840_MAX_PORTS 4 + +#define UMCS7840_READ_LENGTH 1 /* bytes */ +#define UMCS7840_CTRL_TIMEOUT 500 /* ms */ + +/* Read/Wrtire registers vendor commands */ +#define MCS7840_RDREQ 0x0d +#define MCS7840_WRREQ 0x0e + +/* Read/Wrtie EEPROM values */ +#define MCS7840_EEPROM_RW_WVALUE 0x0900 + +/* + * All these registers are documented only in full datasheet, + * which can be requested from MosChip tech support. + */ +#define MCS7840_DEV_REG_SP1 0x00 /* Options for for UART 1, R/W */ +#define MCS7840_DEV_REG_CONTROL1 0x01 /* Control bits for UART 1, + * R/W */ +#define MCS7840_DEV_REG_PINPONGHIGH 0x02 /* High bits of ping-pong + * register, R/W */ +#define MCS7840_DEV_REG_PINPONGLOW 0x03 /* Low bits of ping-pong + * register, R/W */ +/* DCRx_1 Registers goes here (see below, they are documented) */ +#define MCS7840_DEV_REG_GPIO 0x07 /* GPIO_0 and GPIO_1 bits, + * undocumented, see notes + * below R/W */ +#define MCS7840_DEV_REG_SP2 0x08 /* Options for for UART 2, R/W */ +#define MCS7840_DEV_REG_CONTROL2 0x09 /* Control bits for UART 2, + * R/W */ +#define MCS7840_DEV_REG_SP3 0x0a /* Options for for UART 3, R/W */ +#define MCS7840_DEV_REG_CONTROL3 0x0b /* Control bits for UART 3, + * R/W */ +#define MCS7840_DEV_REG_SP4 0x0c /* Options for for UART 4, R/W */ +#define MCS7840_DEV_REG_CONTROL4 0x0d /* Control bits for UART 4, + * R/W */ +#define MCS7840_DEV_REG_PLL_DIV_M 0x0e /* Pre-diviedr for PLL, R/W */ +#define MCS7840_DEV_REG_UNKNOWN1 0x0f /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_PLL_DIV_N 0x10 /* Loop divider for PLL, R/W */ +#define MCS7840_DEV_REG_CLOCK_MUX 0x12 /* PLL input clock & Interrupt + * endpoint control, R/W */ +#define MCS7840_DEV_REG_UNKNOWN2 0x11 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_CLOCK_SELECT12 0x13 /* Clock source for ports 1 & + * 2, R/W */ +#define MCS7840_DEV_REG_CLOCK_SELECT34 0x14 /* Clock source for ports 3 & + * 4, R/W */ +#define MCS7840_DEV_REG_UNKNOWN3 0x15 /* NOT MENTIONED AND NOT USED */ +/* DCRx_2-DCRx_4 Registers goes here (see below, they are documented) */ +#define MCS7840_DEV_REG_UNKNOWN4 0x1f /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWN5 0x20 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWN6 0x21 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWN7 0x22 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWN8 0x23 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWN9 0x24 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWNA 0x25 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWNB 0x26 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWNC 0x27 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWND 0x28 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWNE 0x29 /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_UNKNOWNF 0x2a /* NOT MENTIONED AND NOT USED */ +#define MCS7840_DEV_REG_MODE 0x2b /* Hardware configuration, + * R/Only */ +#define MCS7840_DEV_REG_SP1_ICG 0x2c /* Inter character gap + * configuration for Port 1, + * R/W */ +#define MCS7840_DEV_REG_SP2_ICG 0x2d /* Inter character gap + * configuration for Port 2, + * R/W */ +#define MCS7840_DEV_REG_SP3_ICG 0x2e /* Inter character gap + * configuration for Port 3, + * R/W */ +#define MCS7840_DEV_REG_SP4_ICG 0x2f /* Inter character gap + * configuration for Port 4, + * R/W */ +#define MCS7840_DEV_REG_RX_SAMPLING12 0x30 /* RX sampling for ports 1 & + * 2, R/W */ +#define MCS7840_DEV_REG_RX_SAMPLING34 0x31 /* RX sampling for ports 3 & + * 4, R/W */ +#define MCS7840_DEV_REG_BI_FIFO_STAT1 0x32 /* Bulk-In FIFO Stat for Port + * 1, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BO_FIFO_STAT1 0x33 /* Bulk-out FIFO Stat for Port + * 1, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BI_FIFO_STAT2 0x34 /* Bulk-In FIFO Stat for Port + * 2, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BO_FIFO_STAT2 0x35 /* Bulk-out FIFO Stat for Port + * 2, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BI_FIFO_STAT3 0x36 /* Bulk-In FIFO Stat for Port + * 3, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BO_FIFO_STAT3 0x37 /* Bulk-out FIFO Stat for Port + * 3, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BI_FIFO_STAT4 0x38 /* Bulk-In FIFO Stat for Port + * 4, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_BO_FIFO_STAT4 0x39 /* Bulk-out FIFO Stat for Port + * 4, contains number of + * availiable bytes, R/Only */ +#define MCS7840_DEV_REG_ZERO_PERIOD1 0x3a /* Period between zero out + * frames for Port 1, R/W */ +#define MCS7840_DEV_REG_ZERO_PERIOD2 0x3b /* Period between zero out + * frames for Port 1, R/W */ +#define MCS7840_DEV_REG_ZERO_PERIOD3 0x3c /* Period between zero out + * frames for Port 1, R/W */ +#define MCS7840_DEV_REG_ZERO_PERIOD4 0x3d /* Period between zero out + * frames for Port 1, R/W */ +#define MCS7840_DEV_REG_ZERO_ENABLE 0x3e /* Enable/disable of zero out + * frames, R/W */ +#define MCS7840_DEV_REG_THR_VAL_LOW1 0x3f /* Low 8 bits of threshhold + * value for Bulk-Out for Port + * 1, R/W */ +#define MCS7840_DEV_REG_THR_VAL_HIGH1 0x40 /* High 1 bit of threshhold + * value for Bulk-Out and + * enable flag for Port 1, R/W */ +#define MCS7840_DEV_REG_THR_VAL_LOW2 0x41 /* Low 8 bits of threshhold + * value for Bulk-Out for Port + * 2, R/W */ +#define MCS7840_DEV_REG_THR_VAL_HIGH2 0x42 /* High 1 bit of threshhold + * value for Bulk-Out and + * enable flag for Port 2, R/W */ +#define MCS7840_DEV_REG_THR_VAL_LOW3 0x43 /* Low 8 bits of threshhold + * value for Bulk-Out for Port + * 3, R/W */ +#define MCS7840_DEV_REG_THR_VAL_HIGH3 0x44 /* High 1 bit of threshhold + * value for Bulk-Out and + * enable flag for Port 3, R/W */ +#define MCS7840_DEV_REG_THR_VAL_LOW4 0x45 /* Low 8 bits of threshhold + * value for Bulk-Out for Port + * 4, R/W */ +#define MCS7840_DEV_REG_THR_VAL_HIGH4 0x46 /* High 1 bit of threshhold + * value for Bulk-Out and + * enable flag for Port 4, R/W */ + +/* Bits for SPx registers */ +#define MCS7840_DEV_SPx_LOOP_PIPES 0x01 /* Loop Bulk-Out FIFO to the + * Bulk-In FIFO, default = 0 */ +#define MCS7840_DEV_SPx_SKIP_ERR_DATA 0x02 /* Drop data bytes from UART, + * which were recevied with + * errors, default = 0 */ +#define MCS7840_DEV_SPx_RESET_OUT_FIFO 0x04 /* Reset Bulk-Out FIFO */ +#define MCS7840_DEV_SPx_RESET_IN_FIFO 0x08 /* Reset Bulk-In FIFO */ +#define MCS7840_DEV_SPx_CLOCK_MASK 0x70 /* Mask to extract Baud CLK + * source */ +#define MCS7840_DEV_SPx_CLOCK_X1 0x00 /* CLK = 1.8432Mhz, max speed + * = 115200 bps, default */ +#define MCS7840_DEV_SPx_CLOCK_X2 0x10 /* CLK = 3.6864Mhz, max speed + * = 230400 bps */ +#define MCS7840_DEV_SPx_CLOCK_X35 0x20 /* CLK = 6.4512Mhz, max speed + * = 403200 bps */ +#define MCS7840_DEV_SPx_CLOCK_X4 0x30 /* CLK = 7.3728Mhz, max speed + * = 460800 bps */ +#define MCS7840_DEV_SPx_CLOCK_X7 0x40 /* CLK = 12.9024Mhz, max speed + * = 806400 bps */ +#define MCS7840_DEV_SPx_CLOCK_X8 0x50 /* CLK = 14.7456Mhz, max speed + * = 921600 bps */ +#define MCS7840_DEV_SPx_CLOCK_24MHZ 0x60 /* CLK = 24.0000Mhz, max speed + * = 1.5 Mbps */ +#define MCS7840_DEV_SPx_CLOCK_48MHZ 0x70 /* CLK = 48.0000Mhz, max speed + * = 3.0 Mbps */ +#define MCS7840_DEV_SPx_CLOCK_SHIFT 4 /* Value 0..7 can be shifted + * to get clock value */ +#define MCS7840_DEV_SPx_UART_RESET 0x80 /* Reset UART */ + +/* Bits for CONTROLx registers */ +#define MCS7840_DEV_CONTROLx_HWFC 0x01 /* Enable hardware flow + * control (when power + * down? It is unclear + * in documents), + * default = 0 */ +#define MCS7840_DEV_CONTROLx_UNUNSED1 0x02 /* Reserved */ +#define MCS7840_DEV_CONTROLx_CTS_ENABLE 0x04 /* CTS changes are + * translated to MSR, + * default = 0 */ +#define MCS7840_DEV_CONTROLx_UNUSED2 0x08 /* Reserved for ports + * 2,3,4 */ +#define MCS7840_DEV_CONTROL1_DRIVER_DONE 0x08 /* USB enumerating is + * finished, USB + * enumeration memory + * can be used as FIFOs */ +#define MCS7840_DEV_CONTROLx_RX_NEGATE 0x10 /* Negate RX input, + * works for IrDA mode + * only, default = 0 */ +#define MCS7840_DEV_CONTROLx_RX_DISABLE 0x20 /* Disable RX logic, + * works only for + * RS-232/RS-485 mode, + * default = 0 */ +#define MCS7840_DEV_CONTROLx_FSM_CONTROL 0x40 /* Disable RX FSM when + * TX is in progress, + * works for IrDA mode + * only, default = 0 */ +#define MCS7840_DEV_CONTROLx_UNUSED3 0x80 /* Reserved */ + +/* + * Bits for PINPONGx registers + * These registers control how often two input buffers + * for Bulk-In FIFOs are swapped. One of buffers is used + * for USB trnasfer, other for receiving data from UART. + * Exact meaning of 15 bit value in these registers is unknown + */ +#define MCS7840_DEV_PINPONGHIGH_MULT 128 /* Only 7 bits in PINPONGLOW + * register */ +#define MCS7840_DEV_PINPONGLOW_BITS 7 /* Only 7 bits in PINPONGLOW + * register */ + +/* + * THIS ONE IS UNDOCUMENTED IN FULL DATASHEET, but e-mail from tech support + * confirms, that it is register for GPIO_0 and GPIO_1 data input/output. + * Chips has 2 GPIO, but first one (lower bit) MUST be used by device + * authors as "number of port" indicator, grounded (0) for two-port + * devices and pulled-up to 1 for 4-port devices. + */ +#define MCS7840_DEV_GPIO_4PORTS 0x01 /* Device has 4 ports + * configured */ +#define MCS7840_DEV_GPIO_GPIO_0 0x01 /* The same as above */ +#define MCS7840_DEV_GPIO_GPIO_1 0x02 /* GPIO_1 data */ + +/* + * Constants for PLL dividers + * Ouptut frequency of PLL is: + * Fout = (N/M) * Fin. + * Default PLL input frequency Fin is 12Mhz (on-chip). + */ +#define MCS7840_DEV_PLL_DIV_M_BITS 6 /* Number of useful bits for M + * divider */ +#define MCS7840_DEV_PLL_DIV_M_MASK 0x3f /* Mask for M divider */ +#define MCS7840_DEV_PLL_DIV_M_MIN 1 /* Minimum value for M, 0 is + * forbidden */ +#define MCS7840_DEV_PLL_DIV_M_DEF 1 /* Default value for M */ +#define MCS7840_DEV_PLL_DIV_M_MAX 63 /* Maximum value for M */ +#define MCS7840_DEV_PLL_DIV_N_BITS 6 /* Number of useful bits for N + * divider */ +#define MCS7840_DEV_PLL_DIV_N_MASK 0x3f /* Mask for N divider */ +#define MCS7840_DEV_PLL_DIV_N_MIN 1 /* Minimum value for N, 0 is + * forbidden */ +#define MCS7840_DEV_PLL_DIV_N_DEF 8 /* Default value for N */ +#define MCS7840_DEV_PLL_DIV_N_MAX 63 /* Maximum value for N */ + +/* Bits for CLOCK_MUX register */ +#define MCS7840_DEV_CLOCK_MUX_INPUTMASK 0x03 /* Mask to extract PLL clock + * input */ +#define MCS7840_DEV_CLOCK_MUX_IN12MHZ 0x00 /* 12Mhz PLL input, default */ +#define MCS7840_DEV_CLOCK_MUX_INEXTRN 0x01 /* External (device-depended) + * PLL input */ +#define MCS7840_DEV_CLOCK_MUX_INRSV1 0x02 /* Reserved */ +#define MCS7840_DEV_CLOCK_MUX_INRSV2 0x03 /* Reserved */ +#define MCS7840_DEV_CLOCK_MUX_PLLHIGH 0x04 /* 0 = PLL Output is + * 20MHz-100MHz (default), 1 = + * 100MHz-300MHz range */ +#define MCS7840_DEV_CLOCK_MUX_INTRFIFOS 0x08 /* Enable additional 8 bytes + * fro Interrupt USB pipe with + * USB FIFOs statuses, default + * = 0 */ +#define MCS7840_DEV_CLOCK_MUX_RESERVED1 0x10 /* Unused */ +#define MCS7840_DEV_CLOCK_MUX_RESERVED2 0x20 /* Unused */ +#define MCS7840_DEV_CLOCK_MUX_RESERVED3 0x40 /* Unused */ +#define MCS7840_DEV_CLOCK_MUX_RESERVED4 0x80 /* Unused */ + +/* Bits for CLOCK_SELECTxx registers */ +#define MCS7840_DEV_CLOCK_SELECT1_MASK 0x07 /* Bits for port 1 in + * CLOCK_SELECT12 */ +#define MCS7840_DEV_CLOCK_SELECT1_SHIFT 0 /* Shift for port 1in + * CLOCK_SELECT12 */ +#define MCS7840_DEV_CLOCK_SELECT2_MASK 0x38 /* Bits for port 2 in + * CLOCK_SELECT12 */ +#define MCS7840_DEV_CLOCK_SELECT2_SHIFT 3 /* Shift for port 2 in + * CLOCK_SELECT12 */ +#define MCS7840_DEV_CLOCK_SELECT3_MASK 0x07 /* Bits for port 3 in + * CLOCK_SELECT23 */ +#define MCS7840_DEV_CLOCK_SELECT3_SHIFT 0 /* Shift for port 3 in + * CLOCK_SELECT23 */ +#define MCS7840_DEV_CLOCK_SELECT4_MASK 0x38 /* Bits for port 4 in + * CLOCK_SELECT23 */ +#define MCS7840_DEV_CLOCK_SELECT4_SHIFT 3 /* Shift for port 4 in + * CLOCK_SELECT23 */ +#define MCS7840_DEV_CLOCK_SELECT_STD 0x00 /* STANDARD baudrate derived + * from 96Mhz, default for all + * ports */ +#define MCS7840_DEV_CLOCK_SELECT_30MHZ 0x01 /* 30Mhz */ +#define MCS7840_DEV_CLOCK_SELECT_96MHZ 0x02 /* 96Mhz direct */ +#define MCS7840_DEV_CLOCK_SELECT_120MHZ 0x03 /* 120Mhz */ +#define MCS7840_DEV_CLOCK_SELECT_PLL 0x04 /* PLL output (see for M and N + * dividers) */ +#define MCS7840_DEV_CLOCK_SELECT_EXT 0x05 /* External clock input + * (device-dependend) */ +#define MCS7840_DEV_CLOCK_SELECT_RES1 0x06 /* Unused */ +#define MCS7840_DEV_CLOCK_SELECT_RES2 0x07 /* Unused */ + +/* Bits for MODE register */ +#define MCS7840_DEV_MODE_RESERVED1 0x01 /* Unused */ +#define MCS7840_DEV_MODE_RESET 0x02 /* 0: RESET = Active High + * (default), 1: Reserved (?) */ +#define MCS7840_DEV_MODE_SER_PRSNT 0x04 /* 0: Reserved, 1: Do not use + * hardocded values (default) + * (?) */ +#define MCS7840_DEV_MODE_PLLBYPASS 0x08 /* 1: PLL output is bypassed, + * default = 0 */ +#define MCS7840_DEV_MODE_PORBYPASS 0x10 /* 1: Power-On Reset is + * bypassed, default = 0 */ +#define MCS7840_DEV_MODE_SELECT24S 0x20 /* 0: 4 Serial Ports / IrDA + * active, 1: 2 Serial Ports / + * IrDA active */ +#define MCS7840_DEV_MODE_EEPROMWR 0x40 /* EEPROM write is enabled, + * default */ +#define MCS7840_DEV_MODE_IRDA 0x80 /* IrDA mode is activated + * (could be turned on), + * default */ + +/* Bits for SPx ICG */ +#define MCS7840_DEV_SPx_ICG_DEF 0x24 /* All 8 bits is used as + * number of BAUD clocks of + * pause */ + +/* + * Bits for RX_SAMPLINGxx registers + * These registers control when bit value will be sampled within + * the baud period. + * 0 is very beginning of period, 15 is very end, 7 is the middle. + */ +#define MCS7840_DEV_RX_SAMPLING1_MASK 0x0f /* Bits for port 1 in + * RX_SAMPLING12 */ +#define MCS7840_DEV_RX_SAMPLING1_SHIFT 0 /* Shift for port 1in + * RX_SAMPLING12 */ +#define MCS7840_DEV_RX_SAMPLING2_MASK 0xf0 /* Bits for port 2 in + * RX_SAMPLING12 */ +#define MCS7840_DEV_RX_SAMPLING2_SHIFT 4 /* Shift for port 2 in + * RX_SAMPLING12 */ +#define MCS7840_DEV_RX_SAMPLING3_MASK 0x0f /* Bits for port 3 in + * RX_SAMPLING23 */ +#define MCS7840_DEV_RX_SAMPLING3_SHIFT 0 /* Shift for port 3 in + * RX_SAMPLING23 */ +#define MCS7840_DEV_RX_SAMPLING4_MASK 0xf0 /* Bits for port 4 in + * RX_SAMPLING23 */ +#define MCS7840_DEV_RX_SAMPLING4_SHIFT 4 /* Shift for port 4 in + * RX_SAMPLING23 */ +#define MCS7840_DEV_RX_SAMPLINGx_MIN 0 /* Max for any RX Sampling */ +#define MCS7840_DEV_RX_SAMPLINGx_DEF 7 /* Default for any RX + * Sampling, center of period */ +#define MCS7840_DEV_RX_SAMPLINGx_MAX 15 /* Min for any RX Sampling */ + +/* Bits for ZERO_PERIODx */ +#define MCS7840_DEV_ZERO_PERIODx_DEF 20 /* Number of Bulk-in requests + * befor sending zero-sized + * reply */ + +/* Bits for ZERO_ENABLE */ +#define MCS7840_DEV_ZERO_ENABLE_PORT1 0x01 /* Enable of sending + * zero-sized replies for port + * 1, default */ +#define MCS7840_DEV_ZERO_ENABLE_PORT2 0x02 /* Enable of sending + * zero-sized replies for port + * 2, default */ +#define MCS7840_DEV_ZERO_ENABLE_PORT3 0x04 /* Enable of sending + * zero-sized replies for port + * 3, default */ +#define MCS7840_DEV_ZERO_ENABLE_PORT4 0x08 /* Enable of sending + * zero-sized replies for port + * 4, default */ + +/* Bits for THR_VAL_HIGHx */ +#define MCS7840_DEV_THR_VAL_HIGH_MASK 0x01 /* Only one bit is used */ +#define MCS7840_DEV_THR_VAL_HIGH_MUL 256 /* This one bit is means "256" */ +#define MCS7840_DEV_THR_VAL_HIGH_SHIFT 8 /* This one bit is means "256" */ +#define MCS7840_DEV_THR_VAL_HIGH_ENABLE 0x80 /* Enable threshold */ + +/* These are documented in "public" datasheet */ +#define MCS7840_DEV_REG_DCR0_1 0x04 /* Device contol register 0 for Port + * 1, R/W */ +#define MCS7840_DEV_REG_DCR1_1 0x05 /* Device contol register 1 for Port + * 1, R/W */ +#define MCS7840_DEV_REG_DCR2_1 0x06 /* Device contol register 2 for Port + * 1, R/W */ +#define MCS7840_DEV_REG_DCR0_2 0x16 /* Device contol register 0 for Port + * 2, R/W */ +#define MCS7840_DEV_REG_DCR1_2 0x17 /* Device contol register 1 for Port + * 2, R/W */ +#define MCS7840_DEV_REG_DCR2_2 0x18 /* Device contol register 2 for Port + * 2, R/W */ +#define MCS7840_DEV_REG_DCR0_3 0x19 /* Device contol register 0 for Port + * 3, R/W */ +#define MCS7840_DEV_REG_DCR1_3 0x1a /* Device contol register 1 for Port + * 3, R/W */ +#define MCS7840_DEV_REG_DCR2_3 0x1b /* Device contol register 2 for Port + * 3, R/W */ +#define MCS7840_DEV_REG_DCR0_4 0x1c /* Device contol register 0 for Port + * 4, R/W */ +#define MCS7840_DEV_REG_DCR1_4 0x1d /* Device contol register 1 for Port + * 4, R/W */ +#define MCS7840_DEV_REG_DCR2_4 0x1e /* Device contol register 2 for Port + * 4, R/W */ + +/* Bits of DCR0 registers, documented in datasheet */ +#define MCS7840_DEV_DCR0_PWRSAVE 0x01 /* Shutdown transiver + * when USB Suspend is + * engaged, default = 1 */ +#define MCS7840_DEV_DCR0_RESERVED1 0x02 /* Unused */ +#define MCS7840_DEV_DCR0_GPIO_MODE_MASK 0x0c /* GPIO Mode bits, WORKS + * ONLY FOR PORT 1 */ +#define MCS7840_DEV_DCR0_GPIO_MODE_IN 0x00 /* GPIO Mode - Input + * (0b00), WORKS ONLY + * FOR PORT 1 */ +#define MCS7840_DEV_DCR0_GPIO_MODE_OUT 0x08 /* GPIO Mode - Input + * (0b10), WORKS ONLY + * FOR PORT 1 */ +#define MCS7840_DEV_DCR0_RTS_ACTIVE_HIGH 0x10 /* RTS Active is HIGH, + * default = 0 (low) */ +#define MCS7840_DEV_DCR0_RTS_AUTO 0x20 /* RTS is controlled by + * state of TX buffer, + * default = 0 + * (controlled by MCR) */ +#define MCS7840_DEV_DCR0_IRDA 0x40 /* IrDA mode */ +#define MCS7840_DEV_DCR0_RESERVED2 0x80 /* Unused */ + +/* Bits of DCR1 registers, documented in datasheet */ +#define MCS7840_DEV_DCR1_GPIO_CURRENT_MASK 0x03 /* Mask to extract GPIO + * current value, WORKS + * ONLY FOR PORT 1 */ +#define MCS7840_DEV_DCR1_GPIO_CURRENT_6MA 0x00 /* GPIO output current + * 6mA, WORKS ONLY FOR + * PORT 1 */ +#define MCS7840_DEV_DCR1_GPIO_CURRENT_8MA 0x01 /* GPIO output current + * 8mA, defauilt, WORKS + * ONLY FOR PORT 1 */ +#define MCS7840_DEV_DCR1_GPIO_CURRENT_10MA 0x02 /* GPIO output current + * 10mA, WORKS ONLY FOR + * PORT 1 */ +#define MCS7840_DEV_DCR1_GPIO_CURRENT_12MA 0x03 /* GPIO output current + * 12mA, WORKS ONLY FOR + * PORT 1 */ +#define MCS7840_DEV_DCR1_UART_CURRENT_MASK 0x0c /* Mask to extract UART + * signals current value */ +#define MCS7840_DEV_DCR1_UART_CURRENT_6MA 0x00 /* UART output current + * 6mA */ +#define MCS7840_DEV_DCR1_UART_CURRENT_8MA 0x04 /* UART output current + * 8mA, defauilt */ +#define MCS7840_DEV_DCR1_UART_CURRENT_10MA 0x08 /* UART output current + * 10mA */ +#define MCS7840_DEV_DCR1_UART_CURRENT_12MA 0x0c /* UART output current + * 12mA */ +#define MCS7840_DEV_DCR1_WAKEUP_DISABLE 0x10 /* Disable Remote USB + * Wakeup */ +#define MCS7840_DEV_DCR1_PLLPWRDOWN_DISABLE 0x20 /* Disable PLL power + * down when not needed, + * WORKS ONLY FOR PORT 1 */ +#define MCS7840_DEV_DCR1_LONG_INTERRUPT 0x40 /* Enable 13 bytes of + * interrupt data, with + * FIFO statistics, + * WORKS ONLY FOR PORT 1 */ +#define MCS7840_DEV_DCR1_RESERVED1 0x80 /* Unused */ + +/* + * Bits of DCR2 registers, documented in datasheet + * Wakeup will work only if DCR0_IRDA = 0 (RS-xxx mode) and + * DCR1_WAKEUP_DISABLE = 0 (wakeup enabled). + */ +#define MCS7840_DEV_DCR2_WAKEUP_CTS 0x01 /* Wakeup on CTS change, + * default = 0 */ +#define MCS7840_DEV_DCR2_WAKEUP_DCD 0x02 /* Wakeup on DCD change, + * default = 0 */ +#define MCS7840_DEV_DCR2_WAKEUP_RI 0x04 /* Wakeup on RI change, + * default = 1 */ +#define MCS7840_DEV_DCR2_WAKEUP_DSR 0x08 /* Wakeup on DSR change, + * default = 0 */ +#define MCS7840_DEV_DCR2_WAKEUP_RXD 0x10 /* Wakeup on RX Data change, + * default = 0 */ +#define MCS7840_DEV_DCR2_WAKEUP_RESUME 0x20 /* Wakeup issues RESUME + * signal, DISCONNECT + * otherwise, default = 1 */ +#define MCS7840_DEV_DCR2_RESERVED1 0x40 /* Unused */ +#define MCS7840_DEV_DCR2_SHDN_POLARITY 0x80 /* 0: Pin 12 Active Low, 1: + * Pin 12 Active High, default + * = 0 */ + +/* Interrupt endpoint bytes & bits */ +#define MCS7840_IEP_FIFO_STATUS_INDEX 5 +/* + * Thesse can be calculated as "1 << portnumber" for Bulk-out and + * "1 << (portnumber+1)" for Bulk-in + */ +#define MCS7840_IEP_BO_PORT1_HASDATA 0x01 +#define MCS7840_IEP_BI_PORT1_HASDATA 0x02 +#define MCS7840_IEP_BO_PORT2_HASDATA 0x04 +#define MCS7840_IEP_BI_PORT2_HASDATA 0x08 +#define MCS7840_IEP_BO_PORT3_HASDATA 0x10 +#define MCS7840_IEP_BI_PORT3_HASDATA 0x20 +#define MCS7840_IEP_BO_PORT4_HASDATA 0x40 +#define MCS7840_IEP_BI_PORT4_HASDATA 0x80 + +/* Documented UART registers (fully compatible with 16550 UART) */ +#define MCS7840_UART_REG_THR 0x00 /* Transmitter Holding + * Register W/Only */ +#define MCS7840_UART_REG_RHR 0x00 /* Receiver Holding Register + * R/Only */ +#define MCS7840_UART_REG_IER 0x01 /* Interrupt enable register - + * R/W */ +#define MCS7840_UART_REG_FCR 0x02 /* FIFO Control register - + * W/Only */ +#define MCS7840_UART_REG_ISR 0x02 /* Interrupt Status Registter + * R/Only */ +#define MCS7840_UART_REG_LCR 0x03 /* Line control register R/W */ +#define MCS7840_UART_REG_MCR 0x04 /* Modem control register R/W */ +#define MCS7840_UART_REG_LSR 0x05 /* Line status register R/Only */ +#define MCS7840_UART_REG_MSR 0x06 /* Modem status register + * R/Only */ +#define MCS7840_UART_REG_SCRATCHPAD 0x07 /* Scratch pad register */ + +#define MCS7840_UART_REG_DLL 0x00 /* Low bits of BAUD divider */ +#define MCS7840_UART_REG_DLM 0x01 /* High bits of BAUD divider */ + +/* IER bits */ +#define MCS7840_UART_IER_RXREADY 0x01 /* RX Ready interrumpt mask */ +#define MCS7840_UART_IER_TXREADY 0x02 /* TX Ready interrumpt mask */ +#define MCS7840_UART_IER_RXSTAT 0x04 /* RX Status interrumpt mask */ +#define MCS7840_UART_IER_MODEM 0x08 /* Modem status change + * interrumpt mask */ +#define MCS7840_UART_IER_SLEEP 0x10 /* SLEEP enable */ + +/* FCR bits */ +#define MCS7840_UART_FCR_ENABLE 0x01 /* Enable FIFO */ +#define MCS7840_UART_FCR_FLUSHRHR 0x02 /* Flush RHR and FIFO */ +#define MCS7840_UART_FCR_FLUSHTHR 0x04 /* Flush THR and FIFO */ +#define MCS7840_UART_FCR_RTLMASK 0xa0 /* Mask to select RHR + * Interrupt Trigger level */ +#define MCS7840_UART_FCR_RTL_1_1 0x00 /* L1 = 1, L2 = 1 */ +#define MCS7840_UART_FCR_RTL_1_4 0x40 /* L1 = 1, L2 = 4 */ +#define MCS7840_UART_FCR_RTL_1_8 0x80 /* L1 = 1, L2 = 8 */ +#define MCS7840_UART_FCR_RTL_1_14 0xa0 /* L1 = 1, L2 = 14 */ + +/* ISR bits */ +#define MCS7840_UART_ISR_NOPENDING 0x01 /* No interrupt pending */ +#define MCS7840_UART_ISR_INTMASK 0x3f /* Mask to select interrupt + * source */ +#define MCS7840_UART_ISR_RXERR 0x06 /* Recevir error */ +#define MCS7840_UART_ISR_RXHASDATA 0x04 /* Recevier has data */ +#define MCS7840_UART_ISR_RXTIMEOUT 0x0c /* Recevier timeout */ +#define MCS7840_UART_ISR_TXEMPTY 0x02 /* Transmitter empty */ +#define MCS7840_UART_ISR_MSCHANGE 0x00 /* Modem status change */ + +/* LCR bits */ +#define MCS7840_UART_LCR_DATALENMASK 0x03 /* Mask for data length */ +#define MCS7840_UART_LCR_DATALEN5 0x00 /* 5 data bits */ +#define MCS7840_UART_LCR_DATALEN6 0x01 /* 6 data bits */ +#define MCS7840_UART_LCR_DATALEN7 0x02 /* 7 data bits */ +#define MCS7840_UART_LCR_DATALEN8 0x03 /* 8 data bits */ + +#define MCS7840_UART_LCR_STOPBMASK 0x04 /* Mask for stop bits */ +#define MCS7840_UART_LCR_STOPB1 0x00 /* 1 stop bit in any case */ +#define MCS7840_UART_LCR_STOPB2 0x04 /* 1.5-2 stop bits depends on + * data length */ + +#define MCS7840_UART_LCR_PARITYMASK 0x38 /* Mask for all parity data */ +#define MCS7840_UART_LCR_PARITYON 0x08 /* Parity ON/OFF - ON */ +#define MCS7840_UART_LCR_PARITYODD 0x00 /* Parity Odd */ +#define MCS7840_UART_LCR_PARITYEVEN 0x10 /* Parity Even */ +#define MCS7840_UART_LCR_PARITYODD 0x00 /* Parity Odd */ +#define MCS7840_UART_LCR_PARITYFORCE 0x20 /* Force parity odd/even */ + +#define MCS7840_UART_LCR_BREAK 0x40 /* Send BREAK */ +#define MCS7840_UART_LCR_DIVISORS 0x80 /* Map DLL/DLM instead of + * xHR/IER */ + +/* LSR bits */ +#define MCS7840_UART_LSR_RHRAVAIL 0x01 /* Data available for read */ +#define MCS7840_UART_LSR_RHROVERRUN 0x02 /* Data FIFO/register overflow */ +#define MCS7840_UART_LSR_PARITYERR 0x04 /* Parity error */ +#define MCS7840_UART_LSR_FRAMEERR 0x10 /* Framing error */ +#define MCS7840_UART_LSR_BREAKERR 0x20 /* BREAK sigmal received */ +#define MCS7840_UART_LSR_THREMPTY 0x40 /* THR register is empty, + * ready for transmit */ +#define MCS7840_UART_LSR_HASERR 0x80 /* Has error in receiver FIFO */ + +/* MCR bits */ +#define MCS7840_UART_MCR_DTR 0x01 /* Force DTR to be active + * (low) */ +#define MCS7840_UART_MCR_RTS 0x02 /* Force RTS to be active + * (low) */ +#define MCS7840_UART_MCR_IE 0x04 /* Enable interrupts (from + * code, not documented) */ +#define MCS7840_UART_MCR_LOOPBACK 0x10 /* Enable local loopback test + * mode */ +#define MCS7840_UART_MCR_CTSRTS 0x20 /* Enable CTS/RTS flow control + * in 550 (FIFO) mode */ +#define MCS7840_UART_MCR_DTRDSR 0x40 /* Enable DTR/DSR flow control + * in 550 (FIFO) mode */ +#define MCS7840_UART_MCR_DCD 0x80 /* Enable DCD flow control in + * 550 (FIFO) mode */ + +/* MSR bits */ +#define MCS7840_UART_MSR_DELTACTS 0x01 /* CTS was changed since last + * read */ +#define MCS7840_UART_MSR_DELTADSR 0x02 /* DSR was changed since last + * read */ +#define MCS7840_UART_MSR_DELTARI 0x04 /* RI was changed from low to + * high since last read */ +#define MCS7840_UART_MSR_DELTADCD 0x08 /* DCD was changed since last + * read */ +#define MCS7840_UART_MSR_NEGCTS 0x10 /* Negated CTS signal */ +#define MCS7840_UART_MSR_NEGDSR 0x20 /* Negated DSR signal */ +#define MCS7840_UART_MSR_NEGRI 0x40 /* Negated RI signal */ +#define MCS7840_UART_MSR_NEGDCD 0x80 /* Negated DCD signal */ + +/* SCRATCHPAD bits */ +#define MCS7840_UART_SCRATCHPAD_RS232 0x00 /* RS-485 disabled */ +#define MCS7840_UART_SCRATCHPAD_RS485_DTRRX 0x80 /* RS-485 mode, DTR High + * = RX */ +#define MCS7840_UART_SCRATCHPAD_RS485_DTRTX 0xc0 /* RS-485 mode, DTR High + * = TX */ + +#define MCS7840_CONFIG_INDEX 0 +#define MCS7840_IFACE_INDEX 0 + +#endif diff --git a/sys/dev/usb/usb_process.c b/sys/dev/usb/usb_process.c index 0509ec2..051ded9 100644 --- a/sys/dev/usb/usb_process.c +++ b/sys/dev/usb/usb_process.c @@ -360,7 +360,12 @@ usb_proc_is_gone(struct usb_process *up) if (up->up_gone) return (1); - mtx_assert(up->up_mtx, MA_OWNED); + /* + * Allow calls when up_mtx is NULL, before the USB process + * structure is initialised. + */ + if (up->up_mtx != NULL) + mtx_assert(up->up_mtx, MA_OWNED); return (0); } diff --git a/sys/dev/usb/usbdevs b/sys/dev/usb/usbdevs index eb49eb2..a970206 100644 --- a/sys/dev/usb/usbdevs +++ b/sys/dev/usb/usbdevs @@ -2273,7 +2273,9 @@ product MOBILITY EASIDOCK 0x0304 EasiDock Ethernet /* MosChip products */ product MOSCHIP MCS7703 0x7703 MCS7703 Serial Port Adapter product MOSCHIP MCS7730 0x7730 MCS7730 Ethernet +product MOSCHIP MCS7820 0x7820 MCS7820 Serial Port Adapter product MOSCHIP MCS7830 0x7830 MCS7830 Ethernet +product MOSCHIP MCS7840 0x7840 MCS7840 Serial Port Adapter /* Motorola products */ product MOTOROLA MC141555 0x1555 MC141555 hub controller diff --git a/sys/modules/usb/Makefile b/sys/modules/usb/Makefile index 38f56cb..ddff357 100644 --- a/sys/modules/usb/Makefile +++ b/sys/modules/usb/Makefile @@ -30,7 +30,7 @@ SUBDIR += ehci musb ohci uhci xhci uss820dci ${_at91dci} ${_atmegadci} SUBDIR += rum run uath upgt ural zyd ${_urtw} SUBDIR += atp uhid ukbd ums udbp ufm uep SUBDIR += ucom u3g uark ubsa ubser uchcom ucycom ufoma uftdi ugensa uipaq ulpt \ - umct umodem umoscom uplcom uslcom uvisor uvscom + umct umcs7840 umodem umoscom uplcom uslcom uvisor uvscom SUBDIR += uether aue axe cdce cue kue mos rue udav uhso ipheth SUBDIR += usfs umass urio SUBDIR += quirk template diff --git a/sys/modules/usb/umcs7840/Makefile b/sys/modules/usb/umcs7840/Makefile new file mode 100644 index 0000000..fa03a9e --- /dev/null +++ b/sys/modules/usb/umcs7840/Makefile @@ -0,0 +1,36 @@ +# +# $FreeBSD$ +# +# Copyright (c) 2011 Hans Petter Selasky. All rights reserved. +# +# Redistribution and use in source and binary forms, with or without +# modification, are permitted provided that the following conditions +# are met: +# 1. Redistributions of source code must retain the above copyright +# notice, this list of conditions and the following disclaimer. +# 2. Redistributions in binary form must reproduce the above copyright +# notice, this list of conditions and the following disclaimer in the +# documentation and/or other materials provided with the distribution. +# +# THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND +# ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE +# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE +# ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE +# FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL +# DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS +# OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) +# HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT +# LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY +# OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF +# SUCH DAMAGE. +# + +S= ${.CURDIR}/../../.. + +.PATH: $S/dev/usb/serial + +KMOD= umcs7840 +SRCS= opt_bus.h opt_usb.h device_if.h bus_if.h usb_if.h usbdevs.h \ + umcs7840.c + +.include <bsd.kmod.mk> |