Nuke these two out of date readme files. This stuff should be in de(4)

man pages rather than hidden here anyway.

2 files changed, 0 insertions, 84 deletions

diff --git a/sys/pci/README.de b/sys/pci/README.de
deleted file mode 100644
index 087f465..0000000
--- a/sys/pci/README.de
+++ /dev/null
@@ -1,51 +0,0 @@
-$Id$
-
-THIS FILE IS SERIOUSLY OUT OF DATE AND NO LONGER REFLECTS
-REALITY.  THE ULTIMATE REFERENCE IS THE SOURCE CODE ITSELF.
-				rgrimes@FreeBSD.org
-----------------
-
-The enclosed driver should be considered as beta-test software.  It
-has run on exactly one machine.  Therefore testing has been limited.
-This driver is in no way supported by Digital Equipment.  See the
-disclaimers in the sources for more.
-
-This driver the DEC DE435 PCI NIC.  It should also work with other PCI
-boards that use the 21040-AA chip (also known as TULIP).  This
-driver requires the 21040-AA to be pass 2.3 or later.  If you are
-using a eariler pass chip, you may encounter undetected transmit
-corruptions.  This driver also requires that 21040-AA use a serial
-Ethernet address ROM as described in the 21040 specification.
-
-The DEC DE425 EISA NIC based on the 21040-AA is not support at
-this time.  A future update will include support for it.
-
-The driver includes full support for both BPF and IP Multicast.
-If the autosensing of the driver fails, you can use ifconfig(8) to
-switch the driver to the correct port.
-
-	ifconfig de0 altphys	Thinwire/AUI port
-	ifconfig de0 -altphys	10baseT/UTP port
-
-To enable this driver, you first need to add the following lines to
-your config file (in i386/conf):
-
-        controller pci0
-        device de0
-
-The PCI support code will automatically determine and enable the
-correct IRQ.
-
-Now you are ready to rebuild your kernel, reboot, and see if the
-driver can configure your board.  When the system boots, you will
-hopefully something close to:
-
-	de0 <digital 21040 ethernet> int a irq 9 on pci0:7
-	    reg20: virtual=0xf290a000 physical=0xc0001000
-	de0: enabling Thinwire/AUI port
-	de0: 21040 [10Mb/s] pass 2.3 ethernet address 08:00:2b:e2:1e:09
-	bpf: de0 attached
-
-in the startup log.  If so, the board configured properly and
-should be ready to use.
-
diff --git a/sys/pci/README.de-le b/sys/pci/README.de-le
deleted file mode 100644
index 09443fc..0000000
--- a/sys/pci/README.de-le
+++ /dev/null
@@ -1,33 +0,0 @@
-$Id$
-
-----------------
-
-The enclosed drivers should be considered beta-test software.  These
-drivers are in no way supported by Digital Equipment.  See the
-disclaimers in the sources for more information.  Please be aware that
-Digital does not employee me to write drivers for FreeBSD.
-
-This kit contains one driver:
-
-	de	DEC DE435 PCI NIC or compatible
-
-See README.de for information and installation instruction specific to this
-driver.
-
-Could you please send me the startup messages in the boot
-long along with the type of your PC once the driver configures?  
-
-If you have any problems, comments, suggestions, rant or raves, don't
-hesitate to send me mail @ thomas@lkg.dec.com.
-
-Lastly, if you change or modify the code, I want context diffs of your
-changes.  I want this to the canonical DEC EtherWORKS driver kit for
-FreeBSD, NetBSD, BSD/386, and any other BSD based O/S.  Please make
-sure your diffs are approriate conditionalized.
-
-Thanks,
-Matt Thomas
---
-Mail:	thomas@lkg.dec.com
-URL:	http://ftp.digital.com/~thomas/
-