Remove MII/PHY related junk from here. It's not needed anymore.

1 files changed, 1 insertions, 106 deletions

diff --git a/sys/pci/if_stereg.h b/sys/pci/if_stereg.h
index f602421..78bc215 100644
--- a/sys/pci/if_stereg.h
+++ b/sys/pci/if_stereg.h
@@ -29,7 +29,7 @@
  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
  * THE POSSIBILITY OF SUCH DAMAGE.
  *
- *	$Id: if_stereg.h,v 1.2 1999/08/20 05:13:47 wpaul Exp $
+ *	$Id: if_stereg.h,v 1.1 1999/08/21 18:34:45 wpaul Exp $
  */
 
 /*
@@ -528,111 +528,6 @@ struct ste_mii_frame {
 #define STE_MII_WRITEOP		0x01
 #define STE_MII_TURNAROUND	0x02
 
-#define STE_FLAG_FORCEDELAY	1
-#define STE_FLAG_SCHEDDELAY	2
-#define STE_FLAG_DELAYTIMEO	3
-
-#define PHY_UNKNOWN		6
-
-#define STE_PHYADDR_MIN		0x00
-#define STE_PHYADDR_MAX		0x1F
-
-#define STE_PHY_GENCTL		0x00
-#define STE_PHY_GENSTS		0x01
-#define STE_PHY_VENID		0x02
-#define STE_PHY_DEVID		0x03
-#define STE_PHY_ANAR		0x04
-#define STE_PHY_LPAR		0x05
-#define STE_PHY_ANEXP		0x06
-
-#define PHY_ANAR_NEXTPAGE	0x8000
-#define PHY_ANAR_RSVD0		0x4000
-#define PHY_ANAR_TLRFLT		0x2000
-#define PHY_ANAR_RSVD1		0x1000
-#define PHY_ANAR_RSVD2		0x0800
-#define PHY_ANAR_RSVD3		0x0400
-#define PHY_ANAR_100BT4		0x0200
-#define PHY_ANAR_100BTXFULL	0x0100
-#define PHY_ANAR_100BTXHALF	0x0080
-#define PHY_ANAR_10BTFULL	0x0040
-#define PHY_ANAR_10BTHALF	0x0020
-#define PHY_ANAR_PROTO4		0x0010
-#define PHY_ANAR_PROTO3		0x0008
-#define PHY_ANAR_PROTO2		0x0004
-#define PHY_ANAR_PROTO1		0x0002
-#define PHY_ANAR_PROTO0		0x0001
-
-/*
- * These are the register definitions for the PHY (physical layer
- * interface chip).
- */
-/*
- * PHY BMCR Basic Mode Control Register
- */
-#define PHY_BMCR			0x00
-#define PHY_BMCR_RESET			0x8000
-#define PHY_BMCR_LOOPBK			0x4000
-#define PHY_BMCR_SPEEDSEL		0x2000
-#define PHY_BMCR_AUTONEGENBL		0x1000
-#define PHY_BMCR_RSVD0			0x0800	/* write as zero */
-#define PHY_BMCR_ISOLATE		0x0400
-#define PHY_BMCR_AUTONEGRSTR		0x0200
-#define PHY_BMCR_DUPLEX			0x0100
-#define PHY_BMCR_COLLTEST		0x0080
-#define PHY_BMCR_RSVD1			0x0040	/* write as zero, don't care */
-#define PHY_BMCR_RSVD2			0x0020	/* write as zero, don't care */
-#define PHY_BMCR_RSVD3			0x0010	/* write as zero, don't care */
-#define PHY_BMCR_RSVD4			0x0008	/* write as zero, don't care */
-#define PHY_BMCR_RSVD5			0x0004	/* write as zero, don't care */
-#define PHY_BMCR_RSVD6			0x0002	/* write as zero, don't care */
-#define PHY_BMCR_RSVD7			0x0001	/* write as zero, don't care */
-/*
- * RESET: 1 == software reset, 0 == normal operation
- * Resets status and control registers to default values.
- * Relatches all hardware config values.
- *
- * LOOPBK: 1 == loopback operation enabled, 0 == normal operation
- *
- * SPEEDSEL: 1 == 100Mb/s, 0 == 10Mb/s
- * Link speed is selected byt his bit or if auto-negotiation if bit
- * 12 (AUTONEGENBL) is set (in which case the value of this register
- * is ignored).
- *
- * AUTONEGENBL: 1 == Autonegotiation enabled, 0 == Autonegotiation disabled
- * Bits 8 and 13 are ignored when autoneg is set, otherwise bits 8 and 13
- * determine speed and mode. Should be cleared and then set if PHY configured
- * for no autoneg on startup.
- *
- * ISOLATE: 1 == isolate PHY from MII, 0 == normal operation
- *
- * AUTONEGRSTR: 1 == restart autonegotiation, 0 = normal operation
- *
- * DUPLEX: 1 == full duplex mode, 0 == half duplex mode
- *
- * COLLTEST: 1 == collision test enabled, 0 == normal operation
- */
-
-/* 
- * PHY, BMSR Basic Mode Status Register 
- */   
-#define PHY_BMSR			0x01
-#define PHY_BMSR_100BT4			0x8000
-#define PHY_BMSR_100BTXFULL		0x4000
-#define PHY_BMSR_100BTXHALF		0x2000
-#define PHY_BMSR_10BTFULL		0x1000
-#define PHY_BMSR_10BTHALF		0x0800
-#define PHY_BMSR_RSVD1			0x0400	/* write as zero, don't care */
-#define PHY_BMSR_RSVD2			0x0200	/* write as zero, don't care */
-#define PHY_BMSR_RSVD3			0x0100	/* write as zero, don't care */
-#define PHY_BMSR_RSVD4			0x0080	/* write as zero, don't care */
-#define PHY_BMSR_MFPRESUP		0x0040
-#define PHY_BMSR_AUTONEGCOMP		0x0020
-#define PHY_BMSR_REMFAULT		0x0010
-#define PHY_BMSR_CANAUTONEG		0x0008
-#define PHY_BMSR_LINKSTAT		0x0004
-#define PHY_BMSR_JABBER			0x0002
-#define PHY_BMSR_EXTENDED		0x0001
-
 #ifdef __alpha__
 #undef vtophys
 #define vtophys(va)		(pmap_kextract(((vm_offset_t) (va))) \