Rewrite:

- use pseudo-dma
- provide the same features and interface as sio
- support multiple boards
- fix bugs.

Some compile-time configuration constants are set to support higher
speeds and Cyclom-16Y's at a 30% relative cost in efficiency.
Cyclom-16Y support is untested.

1 files changed, 165 insertions, 88 deletions

diff --git a/sys/i386/isa/ic/cd1400.h b/sys/i386/isa/ic/cd1400.h
index eb690ae..ffebd9a 100644
--- a/sys/i386/isa/ic/cd1400.h
+++ b/sys/i386/isa/ic/cd1400.h
@@ -1,4 +1,4 @@
-/*
+/*-
  * cyclades cyclom-y serial driver
  *	Andrew Herbert <andrew@werple.apana.org.au>, 17 August 1993
  *
@@ -26,96 +26,173 @@
  * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING
  * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
  * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ *	$Id: $
  */
 
-#define CD1400_NO_OF_CHANNELS	4	/* four serial channels per chip */
-#define CD1400_FIFOSIZE		12	/* 12 chars */
-
-/* register definitions */
-
-#define CD1400_CCR		2*0x05	/* channel control */
-#define CD1400_CMD_RESET		0x81	/* full reset */
-
-#define CD1400_SRER		2*0x06	/* service request enable */
-
-#define CD1400_GFRCR		2*0x40	/* global firmware revision code */
-
-#define CD1400_LIVR		2*0x18	/* local intr vector */
-#define CD1400_MIVR		2*0x41	/* modem intr vector */
-#define CD1400_TIVR		2*0x42	/* transmit intr vector */
-#define CD1400_RIVR		2*0x43	/* receive intr vector */
-#define CD1400_RIVR_EXCEPTION		(1<<2)	/* receive exception bit */
-
-#define CD1400_RICR		2*0x44	/* receive intr channel */
-#define CD1400_TICR		2*0x45	/* transmit intr channel */
-#define CD1400_MICR		2*0x46	/* modem intr channel */
-
-#define CD1400_RDCR		2*0x0e	/* rx data count */
-
-#define CD1400_EOSRR		2*0x60	/* end of service request */
-#define CD1400_RDSR		2*0x62	/* rx data/status */
-#define CD1400_RDSR_OVERRUN		(1<<0)	/* rx overrun error */
-#define CD1400_RDSR_FRAMING		(1<<1)	/* rx framing error */
-#define CD1400_RDSR_PARITY		(1<<2)	/* rx parity error */
-#define CD1400_RDSR_BREAK		(1<<3)	/* rx break */
-#define CD1400_RDSR_SPECIAL		(7<<4)	/* rx special char */
-#define CD1400_RDSR_SPECIAL_SHIFT	4	/* rx special char shift */
-#define CD1400_RDSR_TIMEOUT		(1<<7)	/* rx timeout */
-
-#define CD1400_TDR		2*0x63	/* tx data */
-
-#define CD1400_MISR		2*0x4c	/* modem intr status */
-#define CD1400_MISR_DSRd		(1<<7)	/* DSR delta */
-#define CD1400_MISR_CTSd		(1<<6)	/* CTS delta */
-#define CD1400_MISR_RId			(1<<5)	/* RI delta */
-#define CD1400_MISR_CDd			(1<<4)	/* CD delta */
-
-#define CD1400_MSVR		2*0x6d	/* modem signals */
-#define CD1400_MSVR_DSR			(1<<7)	/* !DSR line */
-#define CD1400_MSVR_CTS			(1<<6)	/* !CTS line */
-#define CD1400_MSVR_RI			(1<<5)	/* !RI line */
-#define CD1400_MSVR_CD			(1<<4)	/* !CD line */
-#define CD1400_MSVR_DTR			(1<<1)	/* DTR line */
-
-#define CD1400_DTR		2*0x6d	/* dtr control */
-#define CD1400_DTR_CLEAR		0
-#define CD1400_DTR_SET			(1<<1)
-
-#define CD1400_PPR		2*0x7e
-#define CD1400_CLOCK_25_1MS		0x31
-
-#define CD1400_CAR		2*0x68	/* channel access */
-
-#define CD1400_RIR		2*0x6B	/* receive interrupt status */
-#define CD1400_TIR		2*0x6A	/* transmit interrupt status */
-#define CD1400_MIR		2*0x69	/* modem interrupt status */
-
-#define CD1400_RBPR		2*0x78	/* receive baud rate period */
-#define CD1400_RCOR		2*0x7C	/* receive clock option */
-#define CD1400_TBPR		2*0x72	/* transmit baud rate period */
-#define CD1400_TCOR		2*0x76	/* transmit clock option */
-
-#define CD1400_COR1		2*0x08	/* channel option 1 */
-#define CD1400_COR2		2*0x09	/* channel option 2 */
-#define CD1400_COR3		2*0x0A	/* channel option 3 */
-#define CD1400_COR4		2*0x1E	/* channel option 4 */
-#define CD1400_COR5		2*0x1F	/* channel option 5 */
+/*
+ * Definitions for Cirrus Logic CD1400 serial/parallel chips.
+ */
 
-#define CD1400_SCHR1		2*0x1A	/* special character 1 */
-#define CD1400_SCHR2		2*0x1B	/* special character 2 */
-#define CD1400_SCHR3		2*0x1C	/* special character 3 */
-#define CD1400_SCHR4		2*0x1D	/* special character 4 */
+#define	CD1400_NO_OF_CHANNELS	4	/* 4 serial channels per chip */
+#define	CD1400_RX_FIFO_SIZE	12
+#define	CD1400_TX_FIFO_SIZE	12
 
-#define CD1400_MCOR1		2*0x15	/* modem change 1 */
-#define CD1400_MCOR2		2*0x16	/* modem change 2 */
-#define CD1400_RTPR		2*0x21	/* receive timeout period */
+/*
+ * Global registers.
+ */
+#define	CD1400_GFRCR		0x40	/* global firmware revision code */
+#define	CD1400_CAR		0x68	/* channel access */
+#define	CD1400_CAR_CHAN			(3<<0)	/* channel select */
+#define	CD1400_GCR		0x4B	/* global configuration */
+#define	CD1400_GCR_PARALLEL		(1<<7)	/* channel 0 is parallel */
+#define	CD1400_SVRR		0x67	/* service request */
+#define	CD1400_SVRR_MDMCH		(1<<2)
+#define	CD1400_SVRR_TXRDY		(1<<1)
+#define	CD1400_SVRR_RXRDY		(1<<0)
+#define	CD1400_RICR		0x44	/* receive interrupting channel */
+#define	CD1400_TICR		0x45	/* transmit interrupting channel */
+#define	CD1400_MICR		0x46	/* modem interrupting channel */
+#define	CD1400_RIR		0x6B	/* receive interrupt status */
+#define	CD1400_RIR_RDIREQ		(1<<7)	/* rx service required */
+#define	CD1400_RIR_RBUSY		(1<<6)	/* rx service in progress */
+#define	CD1400_RIR_CHAN			(3<<0)	/* channel select */
+#define	CD1400_TIR		0x6A	/* transmit interrupt status */
+#define	CD1400_TIR_RDIREQ		(1<<7)	/* tx service required */
+#define	CD1400_TIR_RBUSY		(1<<6)	/* tx service in progress */
+#define	CD1400_TIR_CHAN			(3<<0)	/* channel select */
+#define	CD1400_MIR		0x69	/* modem interrupt status */
+#define	CD1400_MIR_RDIREQ		(1<<7)	/* modem service required */
+#define	CD1400_MIR_RBUSY		(1<<6)	/* modem service in progress */
+#define	CD1400_MIR_CHAN			(3<<0)	/* channel select */
+#define	CD1400_PPR		0x7E	/* prescaler period */
+#define	CD1400_PPR_PRESCALER		512
 
-#define CD1400_SVRR		2*0x67	/* service request */
-#define CD1400_SVRR_RX			(1<<0)
-#define CD1400_SVRR_TX			(1<<1)
-#define CD1400_SVRR_MDM			(1<<2)
+/*
+ * Virtual registers.
+ */
+#define	CD1400_RIVR		0x43	/* receive interrupt vector */
+#define	CD1400_RIVR_EXCEPTION		(1<<2)	/* receive exception bit */
+#define	CD1400_TIVR		0x42	/* transmit interrupt vector */
+#define	CD1400_MIVR		0x41	/* modem interrupt vector */
+#define	CD1400_TDR		0x63	/* transmit data */
+#define	CD1400_RDSR		0x62	/* receive data/status */
+#define	CD1400_RDSR_TIMEOUT		(1<<7)	/* rx timeout */
+#define	CD1400_RDSR_SPECIAL_SHIFT	4	/* rx special char shift */
+#define	CD1400_RDSR_SPECIAL		(7<<4)	/* rx special char */
+#define	CD1400_RDSR_BREAK		(1<<3)	/* rx break */
+#define	CD1400_RDSR_PE			(1<<2)	/* rx parity error */
+#define	CD1400_RDSR_FE			(1<<1)	/* rx framing error */
+#define	CD1400_RDSR_OE			(1<<0)	/* rx overrun error */
+#define	CD1400_MISR		0x4C	/* modem interrupt status */
+#define	CD1400_MISR_DSRd		(1<<7)	/* DSR delta */
+#define	CD1400_MISR_CTSd		(1<<6)	/* CTS delta */
+#define	CD1400_MISR_RId			(1<<5)	/* RI delta */
+#define	CD1400_MISR_CDd			(1<<4)	/* CD delta */
+#define	CD1400_EOSRR		0x60	/* end of service request */
 
-/* hardware SVCACK addresses, for use in interrupt handlers */
-#define CD1400_SVCACKR		0x100
-#define CD1400_SVCACKT		0x200
-#define CD1400_SVCACKM		0x300
+/*
+ * Channel registers.
+ */
+#define	CD1400_LIVR		0x18	/* local interrupt vector */
+#define	CD1400_CCR		0x05	/* channel control */
+#define	CD1400_CCR_CMDRESET		(1<<7)	/* enables following: */
+#define	CD1400_CCR_FTF				(1<<1)	/* flush tx fifo */
+#define	CD1400_CCR_FULLRESET			(1<<0)	/* full reset */
+#define	CD1400_CCR_CMDCORCHG		(1<<6)	/* enables following: */
+#define	CD1400_CCR_COR3				(1<<3)	/* COR3 changed */
+#define	CD1400_CCR_COR2				(1<<2)	/* COR2 changed */
+#define	CD1400_CCR_COR1				(1<<1)	/* COR1 changed */
+#define	CD1400_CCR_CMDSENDSC		(1<<5)	/* enables following: */
+#define	CD1400_CCR_SC				(7<<0)	/* special char 1-4 */
+#define	CD1400_CCR_CMDCHANCTL		(1<<4)	/* enables following: */
+#define	CD1400_CCR_XMTEN			(1<<3)	/* tx enable */
+#define	CD1400_CCR_XMTDIS			(1<<2)	/* tx disable */
+#define	CD1400_CCR_RCVEN			(1<<1)	/* rx enable */
+#define	CD1400_CCR_RCVDIS			(1<<0)	/* rx disable */
+#define	CD1400_SRER		0x06	/* service request enable */
+#define	CD1400_SRER_MDMCH		(1<<7)	/* modem change */
+#define	CD1400_SRER_RXDATA		(1<<4)	/* rx data */
+#define	CD1400_SRER_TXRDY		(1<<2)	/* tx fifo empty */
+#define	CD1400_SRER_TXMPTY		(1<<1)	/* tx shift reg empty */
+#define	CD1400_SRER_NNDT		(1<<0)	/* no new data */
+#define	CD1400_COR1		0x08	/* channel option 1 */
+#define	CD1400_COR1_PARODD		(1<<7)
+#define	CD1400_COR1_PARNORMAL		(2<<5)
+#define	CD1400_COR1_PARFORCE		(1<<5)	/* odd/even = force 1/0 */
+#define	CD1400_COR1_PARNONE		(0<<5)
+#define	CD1400_COR1_NOINPCK		(1<<4)
+#define	CD1400_COR1_STOP2		(2<<2)
+#define	CD1400_COR1_STOP15		(1<<2)	/* 1.5 stop bits */
+#define	CD1400_COR1_STOP1		(0<<2)
+#define	CD1400_COR1_CS8			(3<<0)
+#define	CD1400_COR1_CS7			(2<<0)
+#define	CD1400_COR1_CS6			(1<<0)
+#define	CD1400_COR1_CS5			(0<<0)
+#define	CD1400_COR2		0x09	/* channel option 2 */
+#define	CD1400_COR2_IXANY		(1<<7)	/* implied XON mode */
+#define	CD1400_COR2_IXOFF		(1<<6)	/* in-band tx flow control */
+#define	CD1400_COR2_ETC			(1<<5)	/* embedded tx command */
+#define	CD1400_COR2_LLM			(1<<4)	/* local loopback mode */
+#define	CD1400_COR2_RLM			(1<<3)	/* remote loopback mode */
+#define	CD1400_COR2_RTSAO		(1<<2)	/* RTS auto output */
+#define	CD1400_COR2_CCTS_OFLOW		(1<<1)	/* CTS auto enable */
+#define	CD1400_COR2_CDSR_OFLOW		(1<<0)	/* DSR auto enable */
+#define	CD1400_COR3		0x0A	/* channel option 3 */
+#define	CD1400_COR3_SCDRNG		(1<<7)	/* special char detect range */
+#define	CD1400_COR3_SCD34		(1<<6)	/* special char detect 3-4 */
+#define	CD1400_COR3_FTC			(1<<5)	/* flow control transparency */
+#define	CD1400_COR3_SCD12		(1<<4)	/* special char detect 1-2 */
+#define	CD1400_COR3_RXTH		(15<<0)	/* rx fifo threshold */
+#define	CD1400_COR4		0x1E	/* channel option 4 */
+#define	CD1400_COR4_IGNCR		(1<<7)
+#define	CD1400_COR4_ICRNL		(1<<6)
+#define	CD1400_COR4_INLCR		(1<<5)
+#define	CD1400_COR4_IGNBRK		(1<<4)
+#define	CD1400_COR4_NOBRKINT		(1<<3)
+#define	CD1400_COR4_PFO_ESC		(4<<0)	/* parity/framing/overrun... */
+#define	CD1400_COR4_PFO_NUL		(3<<0)
+#define	CD1400_COR4_PFO_DISCARD		(2<<0)
+#define	CD1400_COR4_PFO_GOOD		(1<<0)
+#define	CD1400_COR4_PFO_EXCEPTION	(0<<0)
+#define	CD1400_COR5		0x1F	/* channel option 5 */
+#define	CD1400_COR5_ISTRIP		(1<<7)
+#define	CD1400_COR5_LNEXT		(1<<6)
+#define	CD1400_COR5_CMOE		(1<<5)	/* char matching on error */
+#define	CD1400_COR5_EBD			(1<<2)	/* end of break detected */
+#define	CD1400_COR5_ONLCR		(1<<1)
+#define	CD1400_COR5_OCRNL		(1<<0)
+#define	CD1400_CCSR		0x0B	/* channel control status */
+#define	CD1400_RDCR		0x0E	/* received data count */
+#define	CD1400_SCHR1		0x1A	/* special character 1 */
+#define	CD1400_SCHR2		0x1B	/* special character 2 */
+#define	CD1400_SCHR3		0x1C	/* special character 3 */
+#define	CD1400_SCHR4		0x1D	/* special character 4 */
+#define	CD1400_SCRL		0x22	/* special character range, low */
+#define	CD1400_SCRH		0x23	/* special character range, high */
+#define	CD1400_LNC		0x24	/* lnext character */
+#define	CD1400_MCOR1		0x15	/* modem change option 1 */
+#define	CD1400_MCOR1_DSRzd		(1<<7)	/* DSR one-to-zero delta */
+#define	CD1400_MCOR1_CTSzd		(1<<6)
+#define	CD1400_MCOR1_RIzd		(1<<5)
+#define	CD1400_MCOR1_CDzd		(1<<4)
+#define	CD1400_MCOR1_DTRth		(15<<0)	/* dtrflow threshold */
+#define	CD1400_MCOR2		0x16	/* modem change option 2 */
+#define	CD1400_MCOR2_DSRod		(1<<7)	/* DSR zero-to-one delta */
+#define	CD1400_MCOR2_CTSod		(1<<6)
+#define	CD1400_MCOR2_RIod		(1<<5)
+#define	CD1400_MCOR2_CDod		(1<<4)
+#define	CD1400_RTPR		0x21	/* receive timeout period */
+#define	CD1400_MSVR1		0x6C	/* modem signal value 1 */
+#define	CD1400_MSVR1_RTS		(1<<0)	/* RTS line (r/w) */
+#define	CD1400_MSVR2		0x6D	/* modem signal value 2 */
+#define	CD1400_MSVR2_DSR		(1<<7)	/* !DSR line (r) */
+#define	CD1400_MSVR2_CTS		(1<<6)	/* !CTS line (r) */
+#define	CD1400_MSVR2_RI			(1<<5)	/* !RI line (r) */
+#define	CD1400_MSVR2_CD			(1<<4)	/* !CD line (r) */
+#define	CD1400_MSVR2_DTR		(1<<1)	/* DTR line (r/w) */
+#define	CD1400_PSVR		0x6F	/* printer signal value */
+#define	CD1400_RBPR		0x78	/* receive baud rate period */
+#define	CD1400_RCOR		0x7C	/* receive clock option */
+#define	CD1400_TBPR		0x72	/* transmit baud rate period */
+#define	CD1400_TCOR		0x76	/* transmit clock option */