Document what the pcic driver in newcard will support.

1 files changed, 7 insertions, 145 deletions

diff --git a/share/man/man4/pcic.4 b/share/man/man4/pcic.4
index 02b4119..b7beb6b 100644
--- a/share/man/man4/pcic.4
+++ b/share/man/man4/pcic.4
@@ -32,27 +32,20 @@
 .Nd pccard bridge driver
 .Sh SYNOPSIS
 .Cd device pcic
-.Cd device card
+.Cd device pccard
 .Sh DESCRIPTION
 The
 .Nm
-driver controls the pccard subsystem.
+driver provides support for older ISA and non-Yenta PCI PC Card birdges.
 The
 .Nm
 driver supports most
 .Tn ExCA
-devices attached to either
+devices attached to the
 .Tn ISA
-or
+bus or
 .Tn PCI
-bus.
-The
-.Nm
-driver does not support the so-called TCIC controllers made by
-Databook.
-Nor does it support the MECIA chipset found in some early PC98
-NOTE PC machines.
-The mecia driver now supports that bridge.
+devices that do not conform to the Yenta specification.
 .Pp
 The following
 .Tn ISA
@@ -92,151 +85,20 @@ control system.
 .Tn IBM
 clone of the original i82365SL part, with its own ID register value.
 Has no 3.3V ability.
-.It IBM KING
-A strange clone of i82365SL.
-This part has many restrictions not found in the i82365SL, plus some
-strange power control.
-It has not been tested in ages, but is believed to work.
-Its use is believed to be confined to model of ISA card, available
-only in Japan.
 .El
 .Pp
 Many other vendors made parts in this arena, but most of them were
 compatible with one of the above chipsets.
 .Pp
-The following PCI cardbus and pcmcia bridges are supported:
+The following PCI pcmcia bridges are supported:
 .Pp
 .Bl -tag -width "Intel i82365SL Step A" -compact
 .It Cirrus Logic PD6729
 .It Cirrus Logic PD6730
-These two might be broken at the moment.
-.It Cirrus Logic PD6832
-.It Cirrus Logic PD6833
 .Pp
 .It O2micro OZ6729
 .It O2micro OZ6730
-.It O2micro OZ6812
-.It O2micro OZ6832
-.It O2micro OZ6833
-.It O2micro OZ6836
-.It O2micro OZ6860
-.It O2micro OZ6872
-O2 Micro chips may be poorly supported because the author does not
-have good access to machines with one of these bridges in it.
-.Pp
-.It Ricoh RL4C475
-.It Ricoh RL4C476
-.It Ricoh RL4C477
-.It Ricoh RL4C478
-.Pp
-.It TI PCI-1031
-.It TI PCI-1130
-.It TI PCI-1131
-.It TI PCI-1211
-.It TI PCI-1220
-.It TI PCI-1221
-.It TI PCI-1225
-.It TI PCI-1250
-.It TI PCI-1251
-.It TI PCI-1251B
-.It TI PCI-1410
-.It TI PCI-1420
-.It TI PCI-1450
-.It TI PCI-1451
-.It TI PCI-4451
-.Pp
-.It Toshiba ToPIC95
-.It Toshiba ToPIC97
-.It Toshiba ToPIC100
-.El
-.Sh FILES
-.Bl -tag -width ".Pa /dev/card0" -compact
-.It Pa /dev/card0
-Character device for the
-.Nm
-driver.
-.El
-.Sh MODES OF OPERATION
-The ISA device supports routing ISA interrupts only.
-You cannot share ISA interrupts.
-Every interrupt must be unique.
-.Pp
-The PCI device supports routing ISA or PCI interrupts.
-PCI interrupts are sharable.
-ISA interrupts are not sharable.
-PCI interrupts should be used unless your machine has a specific problem using
-them.
 .Pp
-PCI interrupt routing is the default for PCI devices.
-Some older laptops require ISA interrupt routing to work properly.
-To enable ISA interrupt routing, you must set the tunable
-.Li hw.pcic.intr_path=1
-in
-.Pa /boot/loader.conf .
-For the present, unless you have a one slot machine, you should set
-.Li hw.pcic.irq=0
-to force polling mode.
-Two slot machines have minor issues with using an ISA interrupt for the
-CSC interrupt.
-.Sh TUNABLES
-.Bl -tag -width indent
-.It Va hw.pcic.ignore_function_1
-Needed for some, improperly manufactured PCI cards made by Orinoco.
-It disables function 1 completely.
-Set to 0 to enable function 1.
-Set to 1 to disable function 1.
-This tunable generally should not be needed on laptops.
-The default is 0.
-.It Va hw.pcic.init_routing
-Some machines can tolerate interrupt routing selection at the cardbus
-bridge level.
-Others fail when you mess with these registers.
-Set to 1 to force the chipset to route via parallel PCI interrupts (as
-well as a few other little things).
-Setting to 0, the default, forces the code to leave these registers as the
-code finds them.
-Most laptops will not need to set this tunable.
-Many PCI cards with cardbus chips on them are believed to need this
-tunable set to 1.
-The default is 0.
-.It Va hw.pcic.intr_path
-Should PCI pcic devices route interrupts via ISA or PCI.
-A value of 1 means route via ISA.
-A value of 2 means route via PCI.
-This is ignored for the ISA device.
-Many older laptops do not have PCI BIOS implementations that
-.Fx
-can use to route interrupts properly.
-These laptops may need to set this to 1 and
-.Va hw.pcic.irq
-to a value
-(or 0 for polling).
-The default is 2.
-.It Va hw.pcic.irq
-Overrides the IRQ to use for ISA interrupt routing of the CSC or
-management interrupt.
-If you are using the ISA device, you can set this tunable, or use the
-.Cd "irq N"
-clause in config file.
-If you are using a PCI device in ISA interrupt mode (see
-.Va hw.pcic.intr_path ) ,
-then you must set the interrupt with this
-sysctl, or polling mode will be used.
-Due to limitations in the tunable system, only one interrupt can be selected
-for all cards.
-Systems with multiple PCI bridges that need to use ISA routing are encouraged
-to use polling mode on each of the cards.
-The default is 0.
-.It Va hw.pcic.ignore_pci
-Defaults to 0.
-Set to 1 to completely ignore the cardbus bridge.
-This may help some old laptops work.
-Setting to 1 on newer laptops will almost certainly fail.
 .El
-.Sh HISTORY
-Too long to detail in the man page.
 .Sh BUGS
-Too many to list.
-Some are the fault of the standard.
-Some are the fault of bad standard compliance.
-Some are Warner's fault.
+This does not work at all at the moment.