Update the amr.4 manpage for changes in the driver.

1 files changed, 36 insertions, 31 deletions

diff --git a/share/man/man4/amr.4 b/share/man/man4/amr.4
index fcbdb25..f9e5840 100644
--- a/share/man/man4/amr.4
+++ b/share/man/man4/amr.4
@@ -37,23 +37,33 @@ The
 .Nm
 driver provides support for American Megatrends MegaRAID Express,
 Elite and Enterprise family SCSI RAID controllers,
-including models relabelled and sold by Hewlett Packard and Dell.
+including models relabelled and sold by Hewlett-Packard and Dell.
 Supported controllers include:
 .Bl -bullet
 .It
-MegaRAID 418
+MegaRAID Series 418
 .It
-MegaRAID Enterprise 1200 (428)
+MegaRAID Enterprise 1200 (Series 428)
 .It
-MegaRAID Enterprise 1300
+MegaRAID Enterprise 1300 (Series 434)
 .It
-MegaRAID Enterprise 1400
+MegaRAID Enterprise 1400 (Series 438)
 .It
-MegaRAID Enterprise 1500
+MegaRAID Enterprise 1500 (Series 467)
 .It
-MegaRAID Elite 1500
+MegaRAID Enterprise 1600 (Series 471)
 .It
-MegaRAID Express 300
+MegaRAID Elite 1500 (Series 467)
+.It
+MegaRAID Elite 1600 (Series 493)
+.It
+MegaRAID Express 100 (Series 466WS)
+.It
+MegaRAID Express 200 (Series 466)
+.It
+MegaRAID Express 300 (Series 490)
+.It
+MegaRAID Express 500 (Series 475)
 .It
 Dell PERC
 .It
@@ -61,11 +71,12 @@ Dell PERC 2/SC
 .It
 Dell PERC 2/DC
 .It
-HP NetRAID (all models are believed to work)
+HP NetRAID-1/Si
+.It
+HP NetRAID-3/Si
+.It
+HP Embedded NetRAID
 .El
-.Pp
-Compatible AMI controllers not listed should work,
-but have not been tested.
 .Sh DIAGNOSTICS
 .Ss Driver initialisation/shutdown phase
 .Bl -diag
@@ -81,30 +92,23 @@ The PCI BIOS did not enable busmaster DMA,
 which is required for the correct operation of the controller.
 The driver has enabled this bit and initialisation will proceed.
 .It amr%d: can't allocate register window
+.It amr%d: can't allocate interrupt
+.It amr%d: can't set up interrupt
 .It amr%d: can't allocate parent DMA tag
+.It amr%d: can't allocate buffer DMA tag
 .It amr%d: can't allocate scatter/gather DMA tag
 .It amr%d: can't allocate s/g table
 .It amr%d: can't allocate mailbox tag
 .It amr%d: can't allocate mailbox memory
-.It amr%d: can't allocate interrupt
-.It amr%d: can't set up interrupt
-.It amr%d: can't allocate buffer DMA tag
 .Pp
 A resource allocation error occurred while initialising the driver;
 initialisation has failed and the driver will not attach to this controller.
 .It amr%d: can't obtain configuration data from controller
+.It amr%d: can't obtain product data from controller
 .Pp
 The driver was unable to obtain vital configuration data from the controller.
 Initialisation has failed and the driver will not attach to this controller.
-.It amr%d: controller supports 40ld but CONFIG_PRODINFO failed
-.It amr%d: 40LD firmware unsupported; send controller to msmith@freebsd.org
-.Pp
-This controller provides a firmware interface that is currently unsupported.
-Please contact the author
-(see
-.Sx AUTHOR
-below)
-to determine status of support for this controller.
+.It amr%d: can't establish configuration hook
 .It amr%d: can't scan controller for drives
 .Pp
 The scan for logical drives managed by the controller failed.
@@ -114,10 +118,6 @@ No drives will be attached.
 .Pp
 Creation of the logical drive instances failed;
 attachment of one or more logical drives may have been aborted.
-.It amrd%d: still open, can't shutdown
-.Pp
-The logical drive indicated is still open,
-and the driver cannot shut down.
 .It amr%d: flushing cache...
 .Pp
 The controller cache is being flushed prior to shutdown or detach.
@@ -131,12 +131,17 @@ beyond the end of the logical drive.
 This may also occur if FlexRAID Virtual Sizing is enabled and
 an I/O operation is attempted on a portion of the virtual drive
 beyond the actual capacity available.
+.It amr%d: polled command timeout
+.Pp
+An initialisation command timed out.  The initialisation process may fail as a result.
+.It amr%d: bad slot %d completed
+.Pp
+The controller reported completion of a command that the driver did not issue.  This
+may result in data corruption, and suggests a hardware or firmware problem with the
+system or controller.
 .It amr%d: I/O error - %x
 .Pp
 An I/O error has occurred.
-.It amr%d: controller wedged (not taking commands)
-.Pp
-The controller is not responding to commands.
 .El
 .Sh AUTHORS
 The